Laserfiche WebLink
............. . .. . . ....... <br />SLIP& DRIVE SEAL WATERTIGHT <br />CONNECTION ALL AROUND DUCT BLADE SHAI LBE16GAGE - - - ------------ <br />GALVANIZED STEEL UL LISTED GREASE <br />GASKET EXHAUST FAN <br />DUCT FLANGE <br />SAFETY CHAIN BY <br />G.0NEMA 3R <br />FLASH & <br />COUNTERFLASH BY ROOF CURB BY G.C., DISCONNECT <br />GEN, CONTRACTOR REFER TO ARCH. FACTORY WIRED TO <br />T_ MOTOR <br />DWGS. (D <br />PROVIDE HIGH <br />LU TEMPERATURE DUCT <br />0 0 'ZZI WRAP TO TOP OF <br />ROOFING --\ ---- <br />w <br />D<14" <br />..................... .. . .. . .............. . ..... - - ---- r <br />X CURB EXTENTION, <br />........ . .......................... . . ................ . . .. . ............. <br />GASKET---- 3/8" ROD :f-, TRANSITION FUNNEL <br />FITTING 16 GA. WELDED FIELD WIRING IN <br />1/2" CLEAR ALL 1" WIDE x 16 GAGE LIQUID TIGHT T <br />LIQUID TIGH <br />ROOF DECK, AROUND (MIN,) REGULATOR GALVANIZED STRAP (2 REQ'D) <br />SEE ARCH. —' 'e GREASE -TRAP FLEXIBLE CONDUi r <br />C) <br />DWGS. <br />INDICATING HANDLE AND Z U-1 - ----- . ............. CURB <br />S/M DUCT LOCKNUT - ------- LOCKING QUADRANT w 0 3/8" LAG SCREW 12" _ _VENTED <br />X 0 EXTENSION <br />ROOF LL ON CENTER, MINIMUM <br />OPENING BY 3/8" SQ, ROD W/SET w 0 2 [DER SIDE. — <br />r RESILIENT GASKET <br />G.C. SCREWS (2 REQ'D) <br />U.] <br />7771, <br />> 14" HIGH FACTORY >'11 <br />wo <br />- - ---------- FLASH AND <br />PREFABRICATED <br />COUNTERFLASF <br />ROOF CURB <br />ROOF CURB <br />X <br />DETAIL DUCT THRU ROOF DETAIL ROUND DUCT DAMPER DETAIL <br />X. <br />10 9 7 - -----_- ----- ROOF <br />NONE 16, <br />INSULATION <br />ROOF STRUCTURE <br />x< <br />GREASE EXHAUST DUCT. <br />APPROVED WEATHER CAP MINIMUM 16 GAUGE STEEL <br />WELDED LIQUID TIGHT. <br />PROVIDE FLASHING AND NOTE: <br />COUNTERFLASHING REFER TO STRUCTURAL REFER TO ARCHITECTURAL <br />FOR ANCHOR TO SHEETS FOR ROOFING <br />STRUCTURE ABOVE DETAILS, <br />__.-_-__.._.-- <br />CONCRETE <br />--------- <br />CONCRETE FILLED METAL DECK <br />!N. (76 MM) MIN. <br />LONGITUDINAL OVERLAP KITCHEN EXHAUST FAN DETAIL <br />ON OUTSIDE LAYER 1/8"0 SEISMIC SLACK CABLE . . ...... . ....... . ........ ....... . .... . ........... . . . ....... -4� ­- 3 <br />CEILING NONE <br />INSTALL UL LISTED FIRESTOP (TYP. FOR 4) - 45' SPACE z_ <br />SYSTEM EXHAUST <br />--------- ------ - ------- 7� 7 WITH EQUAL F AND T- RATING AT FAN 16GA. SHEETMETAL <br />PENETRATIONS OF RATED STRAP HANGER <br />CEILING <br />1_(.,2_1Z <br />__---- __- ----- --- ASSEMBLIES FLEX SUPPLY MANUAL VOLUME <br />DUCT <br />TIGLi r COMPRESSION JOINT - 1/2 IN. (13MM) STEEL CEILING G RILLE 16GA, SHEET METAL. DAMPER <br />ON INSIDE LAYER BANDING PLACED 1-1/2 EXHAUST DUCT. C- <br />IN. (38MM) FROM SEE PLANS FOR 7-7 <br />STRAP HANGER <br />TRANSVERSE JOINTS SIZE <br />AND MAXIMUM 12 IN <br />CEILING <br />(305 MM) O.C. <br />ROUND NECK <br />A TOR <br />DAP <br />0 <br />3 IN. (76 MM) MIN. -XI <br />CEILING -- <br />LONGITUDINAL OVERLAP CEILING EXHAUST FAN MOUNTING DETAIL <br />ON OUTSIDE LAYER <br />6 <br />3/8" 0 MIN. <br />NONE <br />HANGER <br />ROD <br />G.I. DUCT HANGER OPPOSED BLADE <br />(TYPICAL) <br />-SEE SCHEDULE BALANCING DAMPER <br />ANGLE IRON SIZED BELOW FOR SIZE (AS SCHEDULED) <br />FASTDOOR XL - UL PER DUCT; REFER TO <br />LISTED DUCT MANUFACTURER'S <br />45" <br />-DAMPER INSTALLATION <br />ACCESS AND ASTM <br />DAMPER <br />4 <br />#10 SMS (TYP.) <br />E2336 COMPLIANT MANUAL. <br />INSULATION COVER <br />M <br />2 x 2 x 16 GA. G.I. <br />Note-, DIAGONAL BRACE <br />Label Re quired ALTERNATE SIDES PLENUM WITH x <br />EVERY HANGER TURNING-;_. . ....... <br />1" MIN, VANES <br />"Access Door <br />Do Not Obstruct CEILING--\ <br />FLEX SUPPLY <br />TYPICAL SQUARE OR =\7 \7 <br />REC FANGULAR DUCT DUCT <br />NOTE: WHERE DUCT IS 6 SF, OR LARGER IN CROSS SECTIONAL AREA - USE <br />2 1/2 x 2 1/2 x 16 GA. VERTICAL, ANGLE IN PLACE OF HANGER AT OPPOSED BLADE <br />SEISMIC BRACE. BALANCING DAMPER --Z -NOTE: <br />(IF REQUIRED) 1. PROVIDE DIFFUSER SUPPORT PER SMACNA RECOMMENDATIONS. <br />MAX. HALF OF MAX. LOAD HANGER SIZE HANGER 2, COORDINATE DIFFUSER INSTALLATION REQUIREMENTS WITH THE <br />NOTES: DUCT PERIMETER EACH HANGER SPACING <br />------ CEILING SYSTEM USED. <br />P/2 = 30" 260 LBS 1" x 22 GA. 101-011 O/C <br />.­­_­ . . . .................... . ... . .. ... . . . . . . .............. ... . .... ............ ........... ­­­ ------- . . .. . . . . . .................................. . .. . <br />1, THERMAL CERAMICS FIRE ATE FAST RAP XL OR PYROSCAT XL HAS BEEN TESTED IN ACCORDANCE WITH ASTM E2336 TO PROVIDE ZERO P/2 72" 420 LBS 1" x 18 Gk 101-01, O/C AL T ERNATIVE-WHEN SPACE IS -LIMITED <br />. .. . ......... . .... . ........ . ............... - - -­-- --- . . . ................ <br />CLEARANCE 1-0 COMBUSTIBLES AND MEETSTHE REQUIREMENTS FOR ONE OR TWO HOUR ENCLOSURES. THROUGH PENETRATIONS FIRESTOP P/2 96" 700 LBS 1" x 16 GA, 101-011 O/C <br />SYSTEMS ARE TESTED IN ACCORDANCE WITH EITHER ASTM E 814 OR UL 1479. ICC -ES APPROVAL, PER REPORT ESR 2213 OR ESR 2832. P/2 120" 1100 LBS 1 1/2" x 16 Gk .--. 101-01, O/C <br />UNDERWRITER'S LABORATORIES (UL) LISTINGS SHOW COMPLIANCE TO UL 1479 FOR THROUGH PENETRATION FIRESTOP SYSTEMS. <br />DUCT SUPPORT DETAIL 5 C'ZILING DIFFUSER TAKE -OFF DETAIL 2 <br />2. INSULATION APPLIED IN TWO LAYERS WITH TIGHT COMPRESSION JOINT ON INSIDE LAYER AND 3 INCH MINIMUM OVERLAPS ON BOTH — ----- <br />SCALE: NONE 5 NONE <br />PERIMETER AND LONGITUDINAL OVERLAPS ON OUTSIDE LAYER. <br />n <br />-TRAP OVER TOP OF <br />EXTENDS <br />UNIT AND SECURE TO OTHER <br />1 GREASE EXHAUST DUCT RUNS FROMTHE HOOD EXHAUST CONNECTION UP TO THE EXHAUST FAN ON THE ROOF WITH MINIMAL TURNS OR <br />SIDE AS SHOWN BELOW <br />BENDS AND MAINTAINING MINIMUM 1/4 UNIT VERTICAL RISE PER 12 UNITS HORIZONTAL RUN. NFPA 96 COMPLIANT ACCESS DOORS LOCATED AFnS <br />T REQUIRED BY CODE. <br />M <br />N 4. THERMAL CERAMICS FIEF ATE ACCESS DOORS AS SPECIFIED IN ICC -ES BUILDING CODE REPORTS ESR 2213 OR ESR 2832. HVAC EQUIPMENT' <br />0 <br />SHEET METAL SCREW THRU TOP OF THERMOS FAT, <br />UNIT BASE SWITCH, OUTLET, CONTROL <br />5. ROOF MOUNTED EXHAUST FAN IS MOUNTED ON A HINGED BASE WHICH ALLOWS ACCESS TCS THE DUCT FROM THE ROOF, <br />T_ <br />GASKET' <br />T <br />< <br />MAX, 0 0 <br />0 <br />------------ <br />6. SUPPORT HANGER SYSTEMS DO NOT NEED TO BE WRAPPED PROVIDEDTHE HANGER RODS ARE AT LEAST A MINIMUM OF 3/8 IN. DIAMETER. TREATED WOOD <br />-RAP <br />16 GA. GALV. STEEL S1 0 <br />NAILER SECUREDTO 2" WIDE (TYPICAL 4 PER CL <br />n- < <br />USE MINIMUM 2 X 2 X,1/8 K S, FEEL ANGLE OR SMACNA EQUIVALENT SUPPORT SYSTEM. CL <br />CURB Ly"THRU WOOD NAILER & CURB <br />z <br />0 <br />ROOF ------- -- - COUNTERFLASHING Q� cr- u) <br />7. THERMAL CERAMICS DUCT ENCLOSURE SYSTEM SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURERS INSTRUCTIONS. \X <br />Cf) I.L. 0 <br />ROOFING <br />— ------- 00 x <br />INSULATION ROOFING <br />< <br />w <br />WRAP SHALL BE INSTALLED ON THE DUCT FROM THE HOOD CONNECTION TO THE CONNECTION TO THE FAN. <br />< 8. THERMAL CERAMICS DUCI T_ <br />o <br />mg ROOF INSULATION <br />�E <br />ROOF STRUCTURE <br />5; FRAME OPENING <br />TH STEEL ANGLE <br />0 W1 <br />------------ <br />NOTE: <br />3/8" THROUGH BOLT, <br />7 G.C. TO SECURE REFER TO ARCHITECTURAL <br />0 WASHERS, UNIT PER DRAWINGS FOR ROOFING <br />�111 LOCKWASHERS, AND NU F z DETAILS. <br />n MANUFACTURERS <br />Fr- <br />: y <br />R\ =_ =-_ <br />AT FOUR CORNERS RECOMENDATIONS <br />GREASE DUCT WRAP DETAIL ROOFTOP UNIT CURB DETAIL ADA CONTROL. DEVICE MOUNTING HEIGHT DETAI2.L <br />8 4 <br />NONE 6X E NONE r <br />b z NONE <br />DESIGN <br />1260 Corona Pointe, Ste 301 <br />Corona, CA 92879 <br />951-251 0136 <br />eidesigninc,com <br />CLIENT INFORMATION <br />w <br />CONTACT: Serena Miller <br />EMAILserena@iburgerim.com <br />PHONE- (€31 3) 650-8307' <br />_lj STAMP <br />0 <br />NOT FOR CONSTRUCTION <br />_U THIS HIS DRAWING IS PROVIDED FOR <br />INFORMATIONAL_ PURPOSES ONLY. APPROVAL <br />FROM THE ARCHITECT AND GOVERNING <br />JURISDICTIONS MUST BE ATTAINED PRIOR TO <br />THE ISSUANCE OF CONSTRUCTION DOCUMENTS. <br />THE ARCHITECT AND HIS CONSULTANIS <br />ASSUME NO RESPONSIBILITY FOR <br />CONSTRUCTION BIDS OR CONSTRUCTION <br />0 PERFORMED FROM THESE DRAWINGS. <br />REVISIONS <br />,y) <br />C/) <br />1") <br />LIJ <br />0 <br />LU <br />Ll_ <br />0 <br />Uj <br />:-D <br />Uj <br />LLS <br />V) <br />CA - <br />0 <br />< <br />C4 <br />0 <br />w <br />CONTACT: Serena Miller <br />EMAILserena@iburgerim.com <br />PHONE- (€31 3) 650-8307' <br />_lj STAMP <br />0 <br />NOT FOR CONSTRUCTION <br />_U THIS HIS DRAWING IS PROVIDED FOR <br />INFORMATIONAL_ PURPOSES ONLY. APPROVAL <br />FROM THE ARCHITECT AND GOVERNING <br />JURISDICTIONS MUST BE ATTAINED PRIOR TO <br />THE ISSUANCE OF CONSTRUCTION DOCUMENTS. <br />THE ARCHITECT AND HIS CONSULTANIS <br />ASSUME NO RESPONSIBILITY FOR <br />CONSTRUCTION BIDS OR CONSTRUCTION <br />0 PERFORMED FROM THESE DRAWINGS. <br />REVISIONS <br />,y) <br />C/) <br />1") <br />LIJ <br />0 <br />LU <br />Ll_ <br />0 <br />Uj <br />:-D <br />Uj <br />LLS <br />V) <br />CA - <br />0 <br />L1.1 <br />Z <br />C4 <br />0 <br />o <br />011 <br />z <br />U -j< <br />c <br />0 <br />U <br />LLA <br />0 <br />0 <br />0 <br />C")z <br />U-1 <br />U <br />L.Li <br />< <br />Cd l <br />DRAWN <br />CHECKED <br />C-) <br />DAVE 2019-02-25 <br />SCALE <br />0 AS NOTED <br />z- ---- --------------- ------- <br />PROJECI <br />M NUMBER <br />Q SHEET <br />0 <br />0 M400 <br />