|
0
<br />v
<br />e
<br />PLUM13ING LEGEND
<br />SYMBOL
<br />DFSIGNATION
<br />ABBREVIATION
<br />DESCRIPTION
<br />EXISTING
<br />NEW
<br />--�
<br />�--- ---�
<br />ACD
<br />AIR CONDITIONING CONDENSATE DRAIN
<br />KS -2
<br />SEE ARCH. E
<br />SHE
<br />CW
<br />COLD WATER
<br />�-----21-----------2
<br />MOP SINK
<br />DHW
<br />DOMESTIC HOT WATER (110"F)
<br />--- -
<br />---------2
<br />DHW (140)
<br />DOMESTIC HOT WATER (140°F)
<br />-c
<br />_
<br />G
<br />NATURAL OR LIQUIFIED PETROLIUM GAS
<br />PRIMER.
<br />FLOOR SINK
<br />S
<br />SANITARY
<br />FLOOR SINK
<br />FS -2
<br />ZURN
<br />ZURN
<br />SEE ARCH.
<br />S
<br />SANITARY BELOW FLOOR/GRADE
<br />r- sv sv
<br />sv -- sv
<br />ST
<br />STORM DRAIN
<br />- v v --
<br />v v
<br />V
<br />VENT LINE
<br />ADA, SIPHON JET
<br />SYMBOL
<br />ABBREVIATION
<br />DESCRIPTION
<br />�- - owl
<br />POC
<br />POINT OF CONNECT TO EXISTING
<br />1. F&I IN MOUNTING BOX. PLACE BOX ABOVE CEILING.
<br />0-0
<br />UP / DOWN
<br />PIPE UP / DOWN
<br />❑o
<br />FS
<br />FLOOR SINK
<br />Uo LJ
<br />FD
<br />FLOOR DRAIN
<br />3.00
<br />UTILITY.
<br />2.25
<br />FIXTURE TRAP W/ VENT CONN.
<br />2
<br />O
<br />HB / WHT
<br />HOSE BIBB / WALL HYDRANT
<br />4.00
<br />SOV / BV /GV
<br />SHUT --OFF, BALL OR GATE VALVE
<br />r/ i
<br />L J
<br />SOV
<br />SHUT-OFF VALVE IN VALVE BOX
<br />2.50
<br />WM
<br />WATER METER IN 80X
<br />JIL O
<br />VTR
<br />VENT THRU ROOF
<br />o XX
<br />CO / FCO / GCO
<br />CLFANOUT / FLOOR / GRADE
<br />XXOO XX
<br />CO / FCO / GOO
<br />2 ----WAY CLEANOUT / FLOOR / GRADE
<br />-NWCO
<br />WCO
<br />WALL CLEANOUT
<br />3.0
<br />225
<br />PIPE TRANSITION
<br />3.00
<br />2.25
<br />FLOW DIRECTION
<br />GB ER AD NOTES:
<br />1. ALL PLUMBING FIXTURES SHALL BE LABELED AS MFFTING EPA WATER SENSE (WWW. EPA. GOV/WATFRSENSE).
<br />2. EXACT LOCATION OF PLUMBING FIXTURES SHALL BE DETERMINED FROM ARCHITECTURAL DRAWINGS.
<br />3. BEFORE SUBMITTING BID, THE PLUMBING CONTRACTOR SHALL REVIEW THE ARCHITECTURAL DRAWINGS AND
<br />INCLUDE IN HIS BID AN AMOUNT TO FURNISH AND INSTALL ANY FIXTURES WHICH ARE SHOWN IN ADDITION
<br />TO FIXTURES SHOWN ON THE PLUMBING DRAWINGS.
<br />4. CONTRACTOR SHALL VERIFY AND COORDINATE LOCATION OF ALL PLUMBINC LINES WITH DUCTWORK AND
<br />ELECTRICAL SERVICES.
<br />5. THE INSTALLATION OF ALL VALVES, UNIONS, THERMOMETERS, GAUGES, OR OTHER INDICATING OR RECORDING
<br />EQUIPMENT, OR SPECIALTIES REQUIRING FREQUENT READING, REPAIRS, ADJUSTMENT, INSPECTION, REMOVAL
<br />OR REPLACEMENT SHALL BE CONVENIENTLY AND ACCESSIBLY LOCATED WITH REFERENCE TO THE FINISHED
<br />BUILDING.
<br />6. WHERE POSSIBLE, COMBINF PLUMBING VENTS TOGETHER SO AS TO MAKE THE MINIMUM NUMBER OF ROOF
<br />PENETRATIONS.
<br />7. WATER CLOSETS IN PUBLIC TOILET ROOMS SHALL CENTER ON THE FINAL LAYOUT OF TOILET PARTITIONS AND
<br />BE INSTALLED AS INDICATEDE IN THE ARCHITECTURAL DRAWINGS.
<br />8. ALL FLUE VENTS AND VTRS THROUGH ROOF SHALL BE A MINIMUM OF 10' FROM ALL AIR INTAKES AND LVAP.
<br />COOLERS.
<br />9. CONTRACTOR SHALL NOT CUT HOLES IN STRUCTURAL MEMBERS WITHOUT FIRST SECURING WRITTEN
<br />APPROVAL FROM ARCHITECT.
<br />10, CONTRACTOR SHALL INSTALL DIELECTRIC UNIONS AT CONNECTION OF DISSIMILAR METALS.
<br />11. CONTRACTOR SHALL ROUGH -IN ALL WASTE AND SUPPLIES TO SPECIAL EQUIP. ACCORDING TO
<br />MANUFACTURERS SHOP DRAWINGS AND MAKE FINAL CONNECTIONS, ALL SUPPLIES SHALL BE VALVED.
<br />12. COPPER POTABLE WATER PIPING VELOCITY: FOR PIPE SIZES < 2y2" PIPE VELOCITY SHALL NOT TO EXCEED 5
<br />FP S.
<br />13. CONTRACTOR SHALL VERIFY INVERT ELEVATION OF SEWERS TO WHICH NEW WASTE LINES ARE TO BE
<br />CONNECTED PRIOR TO MAKING UP OR INSTALLING ANY OF THE NEW SANITARY SYSTEM.
<br />14. FLASHED AND COUNTERFLASH ALL VTRS, PIPES AND FLUES THRU ROOF. MAKE PENETRATIONS WATER TIGI--1 r.
<br />15. NO PLUMBING PIPING SHALL BE INSTALLED IN COMMON DEMISING WALLS.
<br />16. SANITARY LINES SHALL HAVE A MINIMUM SLOPE OF 2% PER CPC SEC 708.0
<br />E ED VERIFICATION N DED
<br />i
<br />NATURAL GAS DOMESTIC HOT WATER HEATER SCHEDULE
<br />GAS (MBH) STOR RECOV EFF WATER TEMP (°F) CONNECTION SIZES (IN) ELEC. OPER. r/1�
<br />MARK MAKE MODEL N0. TANK RATE a COMB (V1PH1 HZ) WEIGHT REMARKS
<br />INPUT OUTPUT (GAL.) (GPH) (70) EWT LWT STOR CW HW GAS FLUE AIR (LBS)
<br />___ ___ a 3!4 314 4 4 120/1/60 73 NOTES 1, 2 &3
<br />MIH -1 RINNAI RUR981(KBP3237FFUD 199 195 98 /0 40 140 --- 314 =
<br />NOTES.
<br />1 F&I WITH FORCED AIR COMBUSTION UNIT, 12 V DC TEMPERATURE CONTROLLER, BUILT-IN RECIRCULATION PUMP, MC-91-2US CONTROLLER, 3 WATTANTI-FROST
<br />PROTECTION, RINNAI THERMAL BYPASS VALVE & IPEX CONCENTRIC 4" VENT KIT. UNIT ACTIVATION FLOW RATE 0.4 GPM.
<br />2 BASED UPON AN ENERGY FACTOR FOR NATURAL GAS = 0.95
<br />3 USE FEMALE UNTHREADED, SOCKETED ENDS, LONG TURN (SWEEP) ELBOWS FOR ALL CHANGES IN FLUE PIPE & COMBUSTION AIR PIPE DIRECTION CHANGES.
<br />1. THE PLUMBING CONTRACTOR SHALL VISIT THE SITE PRIOR TO BID TO FIELD VERIFY ALL EXISTING CONDITIONS WHICH IV AY AFFECT
<br />HIS BID. THE FOLLOWING ITEMS SHALL_ BE VERIFIED.
<br />1.A. PLACEMENT SIZE CAPACITY MANUFACTURER AND CONDITION OF ALL EXISTING PLUMBING EQUIPMENT WITHIN SCOPE OF
<br />WORK, WHETHER SPECIFICALLY SHOWN OR NOT.
<br />1.B. SIZE AND LOCATION OF ALL EXISTING WASTE, GREASE WASTE, VENT AND WATER PIPING.
<br />2. ALL REFERENCES IN THESE DRAWINGS TO EXISTING EQUIPMENT, FIXTURES AND PIPING TO BE VERIFIED BY THE CONTRACTOR
<br />PRIOR TO SUBMITTING THE BID. THE BID SHALL INCLUDE ANY AND ALL AMOUNTS REQUIRED TO ACCOMMODATE EXISTING
<br />CONDITIONS,
<br />3. NO ALLOWANCES WILL BE MADE AFTER THE PROJECT HAS BEEN AWARDED FOR FAILURE TO VERIFY EXISTING CONDITIONS.
<br />4. ANY DISCREPANCIES WHICH MAY AFFECT THE CONTRACTOR BID SHALL BE BROUGHT TO THE ATTENTION OF THE: ENGINEER AND
<br />ARCHITECT FOR DIRECTION.
<br />5. PLUMBING ROUTINGS BASED ON OWNER'S SCHEMATICS OF LOCATION OF EXISTING FIXTURES AND SHELL DRAWINGS. CONTRACTOR
<br />RESPONSIBLE FOR VERIFICATION OF ACTUAL LOCATION OF SUPPLY LINES AND MAKING APPROPRIATE ADJUSTMENTS TO ACTUAL
<br />CONDITIONS IN THE FIELD.
<br />6. CONTRACTOR SHALL VERIFY INVERT ELEVATION OF SEWERS TO WHICH NEW SANITARY LINES ARE TO BE CONNEC I"' C) BEFORI
<br />SUBMITTING THE BID,
<br />7. PRIOR TO CONSTRUCTION VERIFY THE LOCATION OF THE HVAC/WALK-IN CONDENSATE FLOOR SINK. IF SLOPE AND D6TANCIE OR
<br />IF IT IS INFFASIBLE TO DISPOSE OF WALK-IN COOLER CONDENSATE. USE: A CONDENSATE PUMP.
<br />PLUMBING FIXTURES SCHEDULE
<br />vODEL NUMBER FITTING AND CAPACITY ACCESSORIES/REMARKS
<br />FIXTURE
<br />DFSIGNATION
<br />MFR. AND
<br />THERMOSTATIC MIXING VALVE
<br />TMV-1
<br />SYMMONS 7-:
<br />KITCHEN SINK (3 COMP.)
<br />KS -1
<br />SEE ARCH. E
<br />SHE
<br />KITCHEN SINK (1 COMP.)
<br />KS -2
<br />SEE ARCH. E
<br />SHE
<br />RISER TAILPIECE AND P -TRAP.
<br />ET A1.0
<br />SEE ARCH. E
<br />MOP SINK
<br />MS -1
<br />SHE
<br />WATER CLOSET
<br />WC -1
<br />ZURN Z5555 -k
<br />LAVATORY
<br />LV -1
<br />_
<br />DU
<br />SHEET A1.0
<br />PRIMER.
<br />FLOOR SINK
<br />FS-1,FS-3
<br />ZUF
<br />FLOOR SINK
<br />FS -2
<br />ZURN
<br />ZURN
<br />SEE ARCH.
<br />FLOOR DRAIN
<br />FD -1
<br />SHEET A1.0
<br />MPG
<br />HAND SINK
<br />HS -X
<br />SH
<br />GREASE INTERCEPTOR
<br />GT -1
<br />SCHI
<br />ADA, SIPHON JET
<br />FLUSH
<br />JAY R. SMITH
<br />TRAP PRIMER
<br />TP -1
<br />TRAP
<br />OTES:
<br />1. F&I IN MOUNTING BOX. PLACE BOX ABOVE CEILING.
<br />ILLUMINATE UPON SWITCH SENSING WATER.
<br />2. SHUT-OFF VALVES ON UPSTREAM SIDE OF CW & Hti
<br />3. Z8800 STOPS W/FLEXIBLE SUPPLIES; 28700 P -TR,
<br />Z8946 -3 -NT ADA TRAP, STOP & SUPPLY PROTECT
<br />5. POLISHED BRASS 5' SQUARE TOP, IRON BODY WITH
<br />6. JAY R. SMITH 2699 AUTOMATIC TRAP PRIMER.
<br />7. WITH ACID RESISTANT BODY; NICKEL BRONZE DOME
<br />AND NUMBER OF PIPES DISCHARGING TO UNIT.
<br />1. THE PLUMBING CONTRACTOR SHALL VISIT THE SITE PRIOR TO BID TO FIELD VERIFY ALL EXISTING CONDITIONS WHICH IV AY AFFECT
<br />HIS BID. THE FOLLOWING ITEMS SHALL_ BE VERIFIED.
<br />1.A. PLACEMENT SIZE CAPACITY MANUFACTURER AND CONDITION OF ALL EXISTING PLUMBING EQUIPMENT WITHIN SCOPE OF
<br />WORK, WHETHER SPECIFICALLY SHOWN OR NOT.
<br />1.B. SIZE AND LOCATION OF ALL EXISTING WASTE, GREASE WASTE, VENT AND WATER PIPING.
<br />2. ALL REFERENCES IN THESE DRAWINGS TO EXISTING EQUIPMENT, FIXTURES AND PIPING TO BE VERIFIED BY THE CONTRACTOR
<br />PRIOR TO SUBMITTING THE BID. THE BID SHALL INCLUDE ANY AND ALL AMOUNTS REQUIRED TO ACCOMMODATE EXISTING
<br />CONDITIONS,
<br />3. NO ALLOWANCES WILL BE MADE AFTER THE PROJECT HAS BEEN AWARDED FOR FAILURE TO VERIFY EXISTING CONDITIONS.
<br />4. ANY DISCREPANCIES WHICH MAY AFFECT THE CONTRACTOR BID SHALL BE BROUGHT TO THE ATTENTION OF THE: ENGINEER AND
<br />ARCHITECT FOR DIRECTION.
<br />5. PLUMBING ROUTINGS BASED ON OWNER'S SCHEMATICS OF LOCATION OF EXISTING FIXTURES AND SHELL DRAWINGS. CONTRACTOR
<br />RESPONSIBLE FOR VERIFICATION OF ACTUAL LOCATION OF SUPPLY LINES AND MAKING APPROPRIATE ADJUSTMENTS TO ACTUAL
<br />CONDITIONS IN THE FIELD.
<br />6. CONTRACTOR SHALL VERIFY INVERT ELEVATION OF SEWERS TO WHICH NEW SANITARY LINES ARE TO BE CONNEC I"' C) BEFORI
<br />SUBMITTING THE BID,
<br />7. PRIOR TO CONSTRUCTION VERIFY THE LOCATION OF THE HVAC/WALK-IN CONDENSATE FLOOR SINK. IF SLOPE AND D6TANCIE OR
<br />IF IT IS INFFASIBLE TO DISPOSE OF WALK-IN COOLER CONDENSATE. USE: A CONDENSATE PUMP.
<br />PLUMBING FIXTURES SCHEDULE
<br />vODEL NUMBER FITTING AND CAPACITY ACCESSORIES/REMARKS
<br />N Z1751 1 FOR FINISHFD FLOOR AREA I 12" SQ TOP X 8" DEEP. SEE NOTE 7
<br />FD -1749
<br />FD
<br />SET OUTLET TEMPERATURE FOR
<br />12" SQ TOP X 4" DEEP. SFE
<br />NOTE 1
<br />100-102 B SERIES
<br />FOR FINISHED FLOOR AREA
<br />110 F.
<br />NOTE 5
<br />CONDENSATE DRAIN
<br />QUIP. SCHED. ON
<br />SEE
<br />ARCH. EQUIP. SCHED. ON
<br />ANGLE STOPS,
<br />RISER TAILPIECE AND P -TRAP.
<br />ET A1.0
<br />EET A1.0
<br />SHEFT A1.0
<br />SEE NOTE 2
<br />SEE NOTE 2.
<br />QUIZ='. SCHED. ON
<br />SEE
<br />ARCH. EQUIP. SCHED. ON
<br />ANGLE STOPS,
<br />RISER TAILPIECE AND P -TRAP.
<br />ET A1.0
<br />DU
<br />SHEET A1.0
<br />PRIMER.
<br />SEE NOTE 2.
<br />QUIP. SCHED. ON
<br />SFE
<br />ARCH. EQUIP. SCHED. ON
<br />FINISHED FLOOR
<br />NOTE 2
<br />FT A1.0
<br />GPM
<br />SHEET A1.0
<br />MPG
<br />MEDIUM PRESSURE GAS PIPING
<br />PRV
<br />PRESSURE RELIEF VALVE
<br />RD
<br />FLOOR MOUNTFD,
<br />ELONGATED BOWL AND FRONT
<br />ADA, SIPHON JET
<br />FLUSH
<br />TANK, 1.28GAL PER FLUSH
<br />OPEN
<br />SEAT. SEE NOTE 2.
<br />BURN
<br />ZURN
<br />Z81104 -XL -3M FAUCET ON
<br />ANGLE STOPS
<br />W/ EXCUTCHEON & FLEXIBLE
<br />:5340
<br />4" CENTERS
<br />W/4" WRIST BLADES
<br />RISERS.
<br />SEE NOTES 2, 3, 4 & 6.
<br />N Z1751 1 FOR FINISHFD FLOOR AREA I 12" SQ TOP X 8" DEEP. SEE NOTE 7
<br />FD -1749
<br />FD
<br />FOR FINISHED FLOOR AREA
<br />12" SQ TOP X 4" DEEP. SFE
<br />NOTE 7
<br />-2321 -ST
<br />FOR FINISHED FLOOR AREA
<br />F&I WITH TRAP PRIMER. SEE
<br />NOTE 5
<br />CONDENSATE DRAIN
<br />AFF
<br />CW & HW WATER HAMMER ARRESTERS; AIS
<br />EQUIP. SCHED. ON
<br />SEE ARCH. EQUIP, SCHED. ON
<br />STOPS; RISER; TAILPIECE AND
<br />P -TRAP
<br />EET A1.0
<br />SHEET A1.0
<br />SEE NOTE 2
<br />CLEANOUT TO GRADE
<br />ER GB -50
<br />50 GPM 249 LBS CAPACITY
<br />INTEGRATED FLOW CONTROL
<br />DEVICE
<br />2699 AUTOMATIC
<br />DOMESTIC HOT WATER RETURN
<br />DU
<br />DRAINAGE FIXTURE UNITS
<br />PRIMER.
<br />FURNISH AND INSTALL
<br />FCO
<br />FLOOR CLEANOUT
<br />COLD I HOT IWASTE VENT
<br />WATER I WATER SIZE
<br />3/4 3/4 m- - - -
<br />3/4 3/4" 2" 2»
<br />3/4„ 3/4„
<br />3/4» 3/4»
<br />y2" ---
<br />Y2 2
<br />J/2 y2„
<br />2" 2»
<br />3" 2"
<br />3„ 2„
<br />2" 1y"
<br />2
<br />1 y2„ 1 y2„
<br />3» 2„
<br />DRIP PAN TO BE PLACED BELOW MOUNTING BOX WITH MOISTURE SWITCH. PLACE LIGHT IN CEILING TILE NEAR BOX. LIGHT TO
<br />V LINES ABOVE CEILING.
<br />`,P & Z8746 -PC GRID STRAINFR.
<br />QRS FOR OFFSET GRID STRAINER.
<br />CLAMPING COLLAR, ADJUSTABLE NICKFL BRONZE STRAINER ASSEMBLY & TRAP PRIMER CONNECTION WITH PLUG.
<br />STRAINER; CLAMPING COLLAR; AND NON -TILT LOOSE GRATE WITH 112" SQUARE OPENINGS. y2 OR 3/4 GRATE AS REQUIRED BY SIZE
<br />ABBREVIATIONS
<br />ABBREV.
<br />DESCRIPTION
<br />A/C
<br />ABOVE CEILING
<br />A/C
<br />ABOVE GRADE
<br />ACD
<br />CONDENSATE DRAIN
<br />AFF
<br />ABOVE FINISHED FLOOR
<br />B/F
<br />BELOW FLOOR
<br />B/G
<br />BELOW GRADE
<br />BP
<br />BACKFLOW PREVENTER
<br />COTG
<br />CLEANOUT TO GRADE
<br />CW
<br />DOMFSTIC COLD WATER
<br />DHW
<br />DOMESTIC HOT WATER
<br />DHWR
<br />DOMESTIC HOT WATER RETURN
<br />DU
<br />DRAINAGE FIXTURE UNITS
<br />F&I
<br />FURNISH AND INSTALL
<br />FCO
<br />FLOOR CLEANOUT
<br />FF
<br />FINISHED FLOOR
<br />GC
<br />GAS COCK
<br />GPM
<br />GALLONS PER MINUTE
<br />MPG
<br />MEDIUM PRESSURE GAS PIPING
<br />PRV
<br />PRESSURE RELIEF VALVE
<br />RD
<br />ROOF DRAIN
<br />RWL
<br />RAIN WATER LEADER
<br />SD
<br />STORM DRAIN
<br />UON
<br />UNLESS OTHERWISE NOTED
<br />VTR
<br />VENT THRU ROOF
<br />WOO
<br />WALL CLEANOUT
<br />WU
<br />POTABLE WATER FIXTURE UNITS
<br />OW PRESSURE NA I1-iRA L
<br />FIXTURE
<br />CAPACITY
<br />GAS CADU LA_ ON
<br />m
<br />WIDTH
<br />LENGTH
<br />PIPE
<br />DEMAND
<br />APPLIANCES
<br />LENGTH
<br />(MBH)
<br />4704
<br />EFFECTIVE VOLUME
<br />(VOL*0.75/231) GALLONS
<br />15'27
<br />WATER HEATER
<br />199
<br />OVEN --------..-__.. -_
<br />540
<br />RTU -1 J._------
<br />82
<br />(E) RTU -2
<br />45
<br />TOTAL
<br />24
<br />866
<br />IPE LENGTH FROM DEMISING WALL TO METER/PRV
<br />68
<br />EFFECTIVE VOLUME
<br />(VOL*0.75/231)/GALLONS
<br />ASSEMBLY
<br />2 MINUTE PERIOD FLOW
<br />9.35
<br />PIPE FITTINGS EQUIV. LENGTH FROM BLDG TO METER,!I'RV
<br />102
<br />LENGTH
<br />ENGTH OF PIPE 1N TENANT SPACE
<br />j 73
<br />17
<br />15
<br />7
<br />1785
<br />EFFECTIVE VOLUME
<br />(VOL*0.85/231 }/GALLONS
<br />EQJIV. LENGTH OF PIPE IN OR ON THE BUILDING
<br />1''10
<br />3.28
<br />TOTAL EQUIVALENT SYSTEM PIPE LENGTH
<br />212
<br />CW
<br />MAIN
<br />A
<br />N OTES:
<br />HW
<br />1. PIPF SIZING BASED ON 2014 ASPS TABLE 7--5 PIPE SIZING FOR
<br />PRESSURE
<br />LESS THAN 2 PSI AND LOSS OF 0.3 INCH OF WATER COLUMN.
<br />1 0.75
<br />2. CONTRACTOR SHALL VERIFY ACTUAL GAS PRESSURE AVAILABLE,
<br />PIPE
<br />LENGTHS, METER/PRV ASSEMBLY SIZE AND LOCATION PRIOR TO
<br />0.75
<br />CONSTRUCTION. IF PRESSURE IS LESS THAN LISTED ED ABOVE, ACTUAL
<br />PIPE
<br />LENGTH IS MORE THAN LISTED ABOVE, CONTRACTOR SIIALL CONTACT
<br />THE
<br />ENGINEER FOR PIPE SIZING EVALUATION. COORDINATE WITH LOCAL
<br />3.00
<br />UTILITY.
<br />2.25
<br />GREASE TRAP SIZING
<br />FIXTURE
<br />CAPACITY
<br />KITCHEN SINK
<br />WIDTH
<br />LENGTH
<br />HEIGHT
<br />VOLUME IN'
<br />16
<br />21
<br />14
<br />4704
<br />EFFECTIVE VOLUME
<br />(VOL*0.75/231) GALLONS
<br />15'27
<br />3 -COMPARTMENT VOLUME
<br />45.82
<br />2 MINUTE FLOW PFRIOD
<br />22.91
<br />MOP SINK
<br />WIDTH
<br />LENGTH
<br />HEIGHT
<br />VOLUME IN 3
<br />24
<br />24
<br />10
<br />5760
<br />EFFECTIVE VOLUME
<br />(VOL*0.75/231)/GALLONS
<br />18.70
<br />2 MINUTE PERIOD FLOW
<br />9.35
<br />HAND SINK
<br />WIDTH
<br />LENGTH
<br />HEIGHT
<br />VOLUME IN'
<br />17
<br />15
<br />7
<br />1785
<br />EFFECTIVE VOLUME
<br />(VOL*0.85/231 }/GALLONS
<br />6.57
<br />2 MINUTE PERIOD FLOW
<br />3.28
<br />TOTAL FLOW THRU GREASE TRAP
<br />35.54
<br />ASSUMED AVA LAB LE WATER
<br />PRESSURE CALCULATION
<br />STATIC PRESSURE
<br />75.0 PSI
<br />PRESSURE DROP THRU METER
<br />6.0 PSI
<br />PRESSURE DROP @ BACKFLOW PREVENTER
<br />10.0 PSI
<br />AVAILABLE PRESS. ON HOUSE SIDE OF METER
<br />59.0
<br />PSI
<br />STIMATFD PIPE LENGTH - METER TO BLDG WALL
<br />50 FT
<br />EQUIV. LENGTH - METER TO BUILDING WALL
<br />55 FT
<br />P.D. - METER TO BUILDING WALL Q 6 PSIG/100 FT
<br />3.3 PSI
<br />PRESSURE AVAILABLE AT BUILDING WALL
<br />55.7 PSI
<br />PSI REQ- AT END OF THE LINE
<br />20.0 PSI
<br />PRESS. DROP @ THROUGH WATER HEATER
<br />3.0 PSI
<br />PRESS. DROP DUE TO PIPE ELEVATION CHANGES
<br />4.3 PSI
<br />REMAINING PRESSURE
<br />28.4 PSI
<br />SYSTEM LENGTH
<br />125
<br />FT
<br />EQUIVALENT PIPE LENGTH
<br />206
<br />FT
<br />ALLOWABLE LOSS/100FT OF PIPE:
<br />REMAINING PRESS. X 10OFT
<br />13.76
<br />PSI
<br />EQ. LENGTH OF PIPE
<br />FIXTURE UNITS DOMESTIC WATER
<br />FIXTURES
<br />AMNT.CW
<br />INDIVIDUAL
<br />FIXTURE UNITS
<br />CUMMULATIVE FIXTURE
<br />UNITS
<br />TOT
<br />CW
<br />PER
<br />FIXT
<br />HW
<br />PER
<br />FIXT
<br />CW
<br />MAIN
<br />A
<br />CW
<br />HW
<br />LAVATORY (LV -1)
<br />1
<br />1.0
<br />1 0.75
<br />0.75
<br />1.00
<br />0.75
<br />0.75
<br />MOP SINK (MS -1)
<br />1
<br />3.0
<br />2.25
<br />2.25
<br />3.00
<br />2.25
<br />2.25
<br />HAND SINK (HS -1&2)
<br />2
<br />2.0
<br />1.50
<br />1.50
<br />4.00
<br />3.00
<br />3.00
<br />WATER CLOSET (WC -1)
<br />1
<br />2.5
<br />2.50
<br />-
<br />2.50
<br />2.50
<br />-
<br />KITCHEN (KS -1)
<br />1
<br />3.0
<br />2.25
<br />2.25
<br />3.00
<br />2.25
<br />225
<br />KITCHEN (KS -2)
<br />1
<br />3.0
<br />225
<br />2.25
<br />3.00
<br />2.25
<br />2.25
<br />TOTAL
<br />16.5013.00
<br />WM�
<br />10.50
<br />GPM
<br />18.2
<br />16.5
<br />15.0
<br />NOTES AND FIELD CONDITIONS:
<br />1. CONTRACTOR TO FIELD VERIFY SIZE AND LOCATION OF (E) CW
<br />PIPE TO BE AS INDICATED THESE DRAWINGS.
<br />2, CONTRACTOR TO FIELD VERIFY AVAILABLE PRESSURE AT THE
<br />POINT OF CONNECTION (POC) TO THE CW SERVICE. POC TO
<br />CW PIPE TO BE AS INDICATED IN THESE PLANS AT THE
<br />BUILDING WALL.
<br />3, CONTRACTOR SHALL VERIFY ACTUAL WATER PRESSURE AND
<br />PIPE LENGTHS PRIOR TO CONSTRUCTION. IF PRESSURE IS
<br />LESS THAN OR ACTUAL PIPE LENGTH IS MORE THAN LISTED
<br />ABOVE, CONTRACTOR SHALL CONTACT THE ENGINEER FOR
<br />PIPE SIZING EVALUATION. IF PRESSURE EXCEEDS 80 PSI, F&I
<br />A PRESSURE REDUCING VALVE.
<br />POTABLE WATER PIPE SIZ NC
<br />PIPE
<br />SIZE
<br />(IN)
<br />FLUSH
<br />TANK
<br />F. U.
<br />FLUSH
<br />VALVE
<br />F. U.
<br />FLOW
<br />(GPM)
<br />Y2
<br />1.0
<br />-
<br />3.5
<br />%
<br />3.6
<br />-
<br />9.0
<br />1
<br />12
<br />-
<br />13
<br />11/4
<br />29
<br />8
<br />23
<br />1Y2
<br />60
<br />16
<br />32
<br />2
<br />1 165
<br />78
<br />1 58
<br />GNICH
<br />ARCHITECTURE
<br />S T U D I O
<br />9 SE 3RD AVE, SUITE 110
<br />PORTLAND, OR 97214
<br />V. 503.552.9079
<br />F. 503.241.7055
<br />WWW.GNICHARCH.COM
<br />02.11.19
<br />(m
<br />CD
<br />O
<br />'r,,q
<br />o
<br />W
<br />00
<br />00
<br />N
<br />n�
<br />W
<br />C-0
<br />�-1
<br />Q
<br />4-d
<br />V)
<br />6�
<br />�
<br />U
<br />�
<br />O
<br />�
<br />O
<br />WM�
<br />o�
<br />Ngo
<br />O
<br />QJ
<br />_U
<br />�--�
<br />Q
<br />.N
<br />O
<br />ISSUED FOR PERMIT:
<br />02.11.19
<br />SHEET NAME:
<br />PLUMBING LEGEND,
<br />CALCULATIONS
<br />AND SCHEDULES
<br />SHEET NUMBER:
<br />P1.0
<br />COPYRIGHT 2019
<br />
|