|
GENERAL NOTES:
<br />1. DRAWINGS ARE DIAGRAMMATIC ONLY AND REPRESENT THE
<br />GENERAL SCOPE OF THE WORK, PRIOR TO SUBMITTING BID, VISIT
<br />THE JOB SITE TO OBSERVE THE EXISTING CONDITIONS OF THE
<br />PROJECT. REVIEW THE GENERAL NOTES, SPECIFICATIONS AND
<br />PLANS FOR ADDITIONAL REQUIREMENTS THAT MAY NOT BE
<br />SPECIFICALLY CALLED OUT IN THIS PORTION OF THE
<br />CONSTRUCTION DOCUMENTS. NOTIFY OWNER'S CONSTRUCTION
<br />MANAGER OF ANY CONFLICTS OR DISCREPANCIES PRIOR TO
<br />SUBMISSION OF BID,
<br />2. PROVIDE A CONSTRUCTION RECORD SET OF "AS -BUILT"
<br />DOCUMENTS TO THE OWNER'S CONSTRUCTION MANAGER
<br />REFLECTING ANY VARIANCES OF INSTALLED PIPING LOCATIONS
<br />OR EQUIPMENT CONTRARY TO THE CONSTRUCTION DOCUMENTS,
<br />REFER TO SPECIFICATIONS.
<br />3. PROVIDE TO THE OWNER'S CONSTRUCTION MANAGER A COPY OF
<br />INSPECTION REPORTS AND APPROVAL CERTIFICATES FROM
<br />LOCAL AND STATE INSPECTIONS, REFER TO SPECIFICATIONS.
<br />4. INSTALLATION SHALL COMPLY WITH LEGALLY CONSTITUTED
<br />CODES AND THE REQUIREMENTS OF AUTHORITIES HAVING
<br />JURISDICTION AND ALSO MEET ALL REQUIREMENTS OF THE
<br />LANDLORD. OBTAIN A COPY OF THE LANDLORD'S
<br />REQUIREMENTS AND REVIEW PRIOR TO SUBMITTING BID.
<br />5. PLANS AND SPECIFICATIONS GOVERN WHERE THEY EXCEED
<br />CODE REQUIREMENTS.
<br />6. VERIFY LOCATION AND DEPTH OF UTILITIES AT POINTS OF
<br />CONNECTION BEFORE START OF PIPING INSTALLATION.
<br />7. REFER TO ARCHITECTURAL PLANS FOR EXACT LOCATION AND
<br />MOUNTING HEIGHTS OF PLUMBING FIXTURES.
<br />8. DO NOT SCALE FLOOR PLANS FOR EXACT HORIZONTAL LOCATION
<br />OF PIPE ROUTING.
<br />9, INSTALL CONCEALED PIPING TIGHT TO THE STRUCTURE AND AS
<br />HIGH AS POSSIBLE. INSTALL EXPOSED PIPING TIGHT TO THE
<br />STRUCTURE, WALL OR CEILING AND AS HIGH AS POSSIBLE.
<br />COORDINATE WITH OTHER TRADES TO AVOID CONFLICTS.
<br />10, VALVES SHALL BE LINE SIZE UNLESS OTHERWISE NOTED.
<br />11. PIPING IN FINISHED AREAS SHALL BE ROUTED CONCEALED;
<br />EXPOSED PIPING, WHERE NECESSARY, SHALL BE ROUTED AS
<br />HIGH AS POSSIBLE AND TIGHT TO WALLS.
<br />12. COORDINATE ALL WORK WITH OTHER TRADES AND
<br />CONTRACTORS.
<br />13. COORDINATE PIPING INSTALLATION WITH STRUCTURAL GRADE
<br />BEAMS, FOOTINGS, COLUMN PIERS, ETC. SLEEVE PIPING
<br />THROUGH GRADE BEAMS, FOOTING, ETC. WHERE REQUIRED AND
<br />AS NOTED ON PLANS. COORDINATE SLEEVE INSTALLATIONS WITH
<br />THE ARCHITECT, STRUCTURAL ENGINEER, STRUCTURAL
<br />CONTRACTOR AND GENERAL CONTRACTOR BEFORE CONCRETE IS
<br />INSTALLED.
<br />14. CLEAN FAUCET AERATORS AND PIPE STRAINERS PRIOR TO
<br />TURNING BUILDING OVER TO THE OWNER.
<br />15. PROVIDE TRAP PRIMERS WHERE REQUIRED BY LOCAL
<br />AUTHORITIES.
<br />16. COORDINATE PIPE ROUTING AWAY FROM ELECTRICAL PANELS.
<br />DO NOT INSTALL PIPING OVER ELECTRICAL PANELS.
<br />17. PAINT ALL EXPOSED GAS AND WATER PIPING USING RUST
<br />INHIBITOR PAINT. PAINT
<br />AND COLOR SHALL BE COORDINATED
<br />WITH THE ARCHITECT AND / OR OWNER.
<br />18, COORDINATE ALL ROOF PENETRATIONS WITH OTHER TRADES.
<br />MAINTAIN 10' MINIMUM CLEARANCE FROM ALL AIR INTAKES.
<br />MAINTAIN 2' CLEARANCE FROM ALL OTHER EQUIPMENT.
<br />19. INSULATE PIPING ROUTED IN EXTERIOR BUILDING WALLS WITH
<br />VERIFY EXISTING CONDITIONS. THE SUBMISSION OF A BID WILL BE
<br />MINIMUM 2" BATT INSULATION TO PREVENT FREEZING.
<br />20. EXAMINE THE CONTRACT DRAWINGS AND ALL AVAILABLE
<br />INFORMATION CONCERNING EXISTING INSTALLATION, STRUCTURE,
<br />AND LOCAL
<br />CONDITIONS. VISIT THE SITE TO UNDERSTAND THE
<br />NATURE AND SCOPE OF ALL WORK TO BE PERFORMED AND
<br />TAKEN AS EVIDENCE THAT SUCH AN EXAMINATION HAS BEEN
<br />MADE AND THAT ALL EXISTING CONDITIONS HAVE BEEN
<br />CONSIDERED, NO ALLOWANCES WILL BE MADE AFTER THE
<br />PROJECT HAS BEEN AWARDED FOR FAILURE TO VERIFY EXISTING
<br />CONDITIONS. CONTRACTOR SHALL NOTIFY ENGINEER OF ANY
<br />DISCREPANCIES BETWEEN ACTUAL FIELD CONDITIONS AND THAT
<br />OF THESE DRAWINGS PRIOR TO BEGINNING CONSTRUCTION.
<br />21. PLUMBING CONTRACTOR MUST PROVIDE CAMERA VERIFICATION
<br />OF EXACT LOCATION OF WASTE LINE TO GC DURING BID,
<br />VERIFICATION MUST BE MADE PRIOR TO ISSUANCE OF PERMIT
<br />AND AFTER ACCEPTANCE OF CONTRACT TO PROCEED.
<br />22. CONTRACTOR TO FIELD VERIFY EXISTING DOMESTIC WATER
<br />SYSTEM IS PROVIDED WITH A REDUCED PRESSURE BACKFLOW
<br />PREVENTER (RPBP). IF NOT EXISTING, PROVIDE AN APPROVED
<br />RPBP ASSEMBLY SIZED TO MATCH BUILDING WATER METER.
<br />INSTALL NEW RPBP BETWEEN THE WATER METER AND THE
<br />BUILDING PER LOCAL JURISDICTION'S REQUIREMENTS.
<br />FIXTURE BRANCH CONNECTION SCHEDULE
<br />PIPING SYSTEM
<br />FIXTURE
<br />COLD WATER
<br />HOT WATER
<br />WASTE
<br />VENT
<br />WATER CLOSET (TANK)
<br />314"
<br />--
<br />4"
<br />23 RANGE
<br />2"
<br />LAVATORY
<br />112"
<br />1/2"
<br />2"
<br />22 RICE COOKER
<br />2"
<br />JANITOR'S SINK
<br />314"
<br />314"
<br />3"
<br />MECHANICAL EQUIPMENT
<br />2"
<br />FLOOR SINK
<br />--
<br />--
<br />31'
<br />50
<br />1
<br />21
<br />FLOOR DRAIN
<br />--
<br />--
<br />2"
<br />1026
<br />2"
<br />NOTES:
<br />PIPE SIZES SHOWN ARE MINIMUM.
<br />NATURAL GAS SYSTEM SIZED WITH TOTAL DEVELOPED LENGTH FROM GAS METER TO
<br />ESTIMATED TOTAL GREASE WASTE DRAINAGE FIXTURE UNITS:
<br />TOTAL CONNECTED NATURAL GAS LOAD
<br />PIPING SYSTEM
<br />KITCHEN EQUIPMENT
<br />GW
<br />EQUIPMENT
<br />QTY
<br />DESIGNATION DESCRIPTION CFM (EACH)
<br />24 FRYER
<br />100
<br />24 FRYER
<br />100
<br />23 RANGE
<br />227
<br />25 GRI DDLE
<br />219
<br />22 RICE COOKER
<br />35
<br />22 RICE COOKER
<br />35
<br />45 GRIDDLE
<br />110
<br />TOTAL =
<br />826
<br />MECHANICAL EQUIPMENT
<br />1
<br />EQUIPMENT
<br />4.0
<br />DESIGNATION DESCRIPTION CFH (EACH)
<br />WH -1 WATER HEATER
<br />50
<br />RTU-1(EXISTING) ROOF TOP UNIT
<br />150
<br />TOTAL =
<br />200
<br />TOTAL CONNECTED LOAD -
<br />1026
<br />NATURAL GAS SYSTEM OPERATING PRESSURE OF 7 INCHES WC
<br />1 0.5 1
<br />NATURAL GAS SYSTEM SIZED WITH TOTAL DEVELOPED LENGTH FROM GAS METER TO
<br />ESTIMATED TOTAL GREASE WASTE DRAINAGE FIXTURE UNITS:
<br />MOST REMOTE PIECE OF EQUIPMENT OF 125WITH A PRESSURE DROP OF 0.5 INCHES
<br />W•C.
<br />KITCHEN GENERAL NOTES:
<br />1. REFERENCE THE KITCHEN EQUIPMENT PLUMBING CONNECTION
<br />SCHEDULE FOR ITEMS TO BE FURNISHED AND / OR INSTALLED AS
<br />REQUIRED TO COMPLETE THE INSTALLATION OF PLUMBING
<br />SYSTEMS FOR KITCHEN EQUIPMENT. REFERENCE KITCHEN
<br />EQUIPMENT DRAWINGS FOR THE EXACT LOCATION OF EQUIPMENT
<br />AND ROUGH --IN. REFERENCE THE KITCHEN EQUIPMENT SHOP
<br />DRAWINGS AND COORDINATE WITH THE OWNER FOR EXACT
<br />REQUIREMENTS PRIOR TO THE START OF INSTALLATION.
<br />2. PROVIDE ITEMS AND WORK AS REQUIRED FOR A COMPLETE AND
<br />WORKING PLUMBING INSTALLATION FOR EACH PIECE OF KITCHEN
<br />EQUIPMENT. PROVIDE ROUGH -INS AND CONNECT TO THE KITCHEN
<br />EQUIPMENT WITH TRAPS, SUPPLIES, SHUTOFF VALVES, PIPES TO
<br />THE WALL, ESCUTCHEONS, ETC AS SHOWN, SPECIFIED AND
<br />REQUIRED.
<br />3. VERIFY GAS LOADS AND GAS ROUGH --IN OF KITCHEN EQUIPMENT
<br />WITH THE KITCHEN EQUIPMENT SHOP DRAWINGS PRIOR TO
<br />INSTALLING GAS PIPING. PROVIDE GAS COCKS, UNIONS, ETC. AS
<br />SPECIFIED AND REQUIRED. INSTALL GAS QUICK DISCONNECTS
<br />WHERE FURNISHED WITH THE KITCHEN EQUIPMENT.
<br />4. PROVIDE INDIRECT WASTE LINES OF SAME SIZE AS CONNECTION
<br />TO EQUIPMENT WITH 3/4" BEING MINIMUM SIZE. ROUTE FROM
<br />EQUIPMENT CONNECTION POINTS INDICATED TO FLOOR DRAIN OR
<br />FLOOR SINK. PROVIDE AIR GAP OF TWO PIPE DIAMETERS
<br />MINIMUM PER CODE.
<br />5. COMPLY WITH HEALTH DEPARTMENT REGULATIONS. PROVIDE
<br />CLEARANCE FOR CLEANING BEHIND. AND UNDER EXPOSED PIPING
<br />AS REQUIRED BY HEALTH DEPARTMENT. CONFORM TO HEALTH
<br />DEPARTMENT REQUIREMENTS FOR LOCATIONS OF FLOOR SINKS.
<br />6. PROVIDE AIRTIGHT SEAL AROUND PIPING PENETRATIONS
<br />THROUGH WALK-IN COOLER OR FREEZER WALLS OR CEILINGS.
<br />7. DO NOT INSTALL PIPING IN COOLER OR FREEZER WALLS. INSTALL
<br />EXPOSED PIPING IN A NEAT APPEARING MANNER.
<br />8. COORDINATE FLOOR DRAIN LOCATION AND FLOOR SLOPE
<br />REQUIREMENTS WITH THE ARCHITECT.
<br />9. INSTALL RIM OF FLOOR DRAINS AND FLOOR SINKS BELOW
<br />FINISHED FLOOR LEVEL. SLOPE FLOOR TO DRAINS. REFER TO
<br />ARCHITECTURAL DRAWINGS FOR EXACT LOCATION.
<br />10. COORDINATE LOCATION OF VENT, WATER, AND GAS PIPING TO
<br />AVOID CONFLICT WITH OTHER TRADES.
<br />11. CLEAN INSTALLED PLUMBING FIXTURES AND EQUIPMENT,
<br />12, PROVIDE WALL BACKING OR SPECIFIED CARRIERS FOR THE
<br />PROPER SUPPORT OF INSTALLED WALL HUNG FIXTURES AND
<br />EQUIPMENT.
<br />13. PROVIDE VERTICAL LIFT SPRING LOADED CHECK VALVES IN HOT
<br />AND COLD WATER SUPPLIES FOR 3 -COMPARTMENT SINKS, PRE -
<br />RINSE UNITS, JANITOR SINKS, MIXING HOSE BIBBS & MIXING WALL
<br />HYDRANTS DOWNSTREAM OF SHUTOFF VALVES.
<br />GREASE INTERCEPTOR SIZING
<br />PIPING SYSTEM
<br />FIXTURE TYPE
<br />GW
<br />GW
<br />QTY
<br />D.F.U.
<br />D.F.U.
<br />S, W OR V
<br />(EA)
<br />TOTAL
<br />SERVICE SINK (MOP BASIN)
<br />1
<br />3.0
<br />3.0
<br />SINK (HAND) (2" DW)
<br />2
<br />2.0
<br />4.0
<br />SINK (2 COMPARTMENT) (2" IW)
<br />1
<br />3.0
<br />3.0
<br />SINK (3 COMPARTMENT) (2" IW)
<br />1
<br />4.0
<br />4.0
<br />2" FLOOR DRAIN IN GRFASE PRODUCING AREA
<br />3
<br />2.0
<br />6.0
<br />HOT FOOD TABLE (314" IW)
<br />1
<br />0.5
<br />0.5
<br />DIPPER WELL (314" IW)
<br />1 1
<br />1 0.5 1
<br />0.5
<br />ESTIMATED TOTAL GREASE WASTE DRAINAGE FIXTURE UNITS:
<br />4.7
<br />21.0
<br />PER TABLE 1014.3.6 OF THE 2016 CPG, 21 DFU CAN BE
<br />3.0
<br />3.0
<br />PLUMBED TO AN EXISTING 2,000 GALLON GREASE INTERCEPTOR
<br />32
<br />4
<br />Number of DFU's 21.0
<br />22.0
<br />19.75
<br />TABLE 10-3
<br />19.5
<br />1-1/2"
<br />GRAVITY GREASE INTERCEPTOR S123NG
<br />15.8
<br />5.9
<br />DFU's (1) INTERCEPTOR VOLUME (2)
<br />44.3
<br />5
<br />8 500 gallons
<br />2"
<br />214
<br />21 (3) 750 gallons
<br />7.5
<br />72.0
<br />35 1,000 gallons
<br />5
<br />48
<br />90 (3) 1,250 gallons
<br />476
<br />360
<br />172 1,500 gallons
<br />119.3
<br />245
<br />216 2,000 gallons
<br />74
<br />3"
<br />PLUMBING PIPE MATERIAL SCHEDULE
<br />PIPING SYSTEM
<br />ABBREVIATION
<br />PIPING MATERIAL
<br />SANITARY DRAINAGE & VENT (ABOVE GRADE)
<br />S, W OR V
<br />HUBLESS CAST IRON
<br />SANITARY DRAINAGE & VENT (BELOW GRADE)
<br />S, W OR V
<br />PVC DWV
<br />POTABLE WATER (ABOVE GRADE)
<br />CW, HW OR HWR
<br />TYPE L HARD DRAWN COPPER WITH SOLDERED JOINTS
<br />POTABLE WATER - 2" & SMALLER (BELOW GRADE)
<br />CW, HW OR HWR
<br />TYPE K SOFT ANNEALED COPPER
<br />NATURAL GAS (ABOVE GRADE & ON ROOF)
<br />G
<br />SCHEDULE 40 BLACK STEEL
<br />NATURAL GAS (BELOW GRADE)
<br />G
<br />APPROVED'PE' PIPE FOR GAS
<br />CONDENSATE DRAIN - 1" & SMALLER
<br />CD
<br />TYPE M HARD DRAWN COPPER
<br />CONDENSATE DRAIN - 1-114" & LARGER
<br />CD
<br />TYPE DWV HARD DRAWN COPPER
<br />INDIRECT DRAIN - 1"& SMALLER
<br />ID
<br />TYPE M HARD DRAWN COPPER
<br />INDIRECT DRAIN - 1-114" & LARGER
<br />ID
<br />TYPE DWV HARD DRAWN COPPER
<br />REFER TO SPECIFICATIONS FOR FITTINGS, INSTALLATION REQUIREMENTS AND FURTHER INFORMATION
<br />PLUMBING FIXTURE SCHEDULE:
<br />FIXTURES IN THIS SCHEDULE OR THEIR APPROVED EQUIVALENT
<br />ARE PROVIDED BY THE PLUMBING CONTRACTOR. SUBMIT SHOP
<br />DRAWINGS ON EACH OF THESE ITEMS. REFER TO
<br />SPECIFICATIONS FOR FURTHER INFORMATION AND INSTALLATION
<br />REQUIREMENTS. VERIFY ROUGH -IN REQUIREMENTS WITH
<br />MANUFACTURER'S INSTALLATION INSTRUCTIONS AND INSTALL PER
<br />MANUFACTURER'S RECOMMENDATIONS. REFER TO THE
<br />ARCHITECTURAL DRAWINGS FOR THE PLUMBING FIXTURE
<br />MOUNTING HEIGHTS.
<br />AP AQU __PANEL: JAY R. SMITH # 4762 - 12" x 12" - CL,
<br />TYPE 304 STAINLESS STEEL PANEL AND FRAME WITH CONCEALED
<br />HINGE, KEY OPERATED CYLINDER LOCK. PROVIDE WITH NAILER
<br />SLOTS FOR INSTALLATION IN STUD WALLS AND ANCHOR STRAPS
<br />FOR INSTALLATION IN MASONRY CONSTRUCTION.
<br />BFP) DOUBLE CHECKF OWPRE-VENTER:
<br />WATTS # 719QT-S, CAST BRONZE BODY, QUARTER TURN TEST
<br />COCKS, QUARTER TURN BALL VALVES, BRONZE STRAINER, AND #
<br />909AG AIR GAP FITTING.
<br />0 EXPANSION TANK: AMTROL "THERM-X-TROL" # ST -5,
<br />WELDED STEEL PRESSURE TANK, POLYPROPYLENE LINING,
<br />FLEXIBLE BUTYL DIAPHRAGM, AIR CHARGING VALVE, 150 PSI
<br />MAXIMUM WORKING PRESSURE, 2.0 GALLON CAPACITY, 0.45
<br />MAXIMUM ACCEPTANCE FACTOR, 3/4" PIPE CONNECTION. SET THE
<br />AIR CHARGE PRESSURE TO MATCH EXISTING WATER SYSTEM
<br />PRESSURE.
<br />FCO PVQ _ EMOR CLEANOUT: SIOUX CHIEF # 852 SERIES WITH
<br />SQUARE SCQRIATED MEDIUM DUTY CAST NICKEL ADJUSTABLE
<br />TOP, IN UNFINISHED AREAS, WITH FLANGED PVC ADAPTER WITH
<br />BLANK TRAP PRIMER PORT AND POLYPROPYLENE THREADED
<br />PLASTIC PLUG WITH THREADED BRASS INSERT. INSTALL WITH
<br />CARPET MARKER IN CARPETED FLOOR AREAS. CLEAN AND
<br />POLISH TOP AFTER INSTALLATION WHERE EXPOSED. REFER TO
<br />SPECIFICATIONS FOR INSTALLATION.
<br />FD F QM DRAIN: ZURN # FD-2320-NH3-ST-P, CAST IRON
<br />BODY AND CLAMPING COLLAR, ADJUSTABLE 6" SQUARE NICKEL
<br />BRONZE STRAINER. USE PUSH -ON JOINT OF OUTLET SIZE AS
<br />SHOWN ON PLANS.
<br />FS FLOOR SINK: ZURN # FD2375, 6" DEEP CAST IRON BODY
<br />WITH ACID RESISTING ENAMELED INTERIOR, ANCHOR FLANGE WITH
<br />SEEPAGE HOLES, CLAMP COLLAR, ABS DOME STRAINER, NICKEL
<br />BRONZE RIM AND HALF/FULL GRATE. USE CAULK JOINT OF
<br />OUTLET SIZE AS SHOWN ON PLANS.
<br />LV WALL -MOUNTED A AMERICAN
<br />STANDARD # 0355.012 "LUCERNE" 20-1/2" X 18-1/4" RECTANGULAR WALL
<br />MOUNTED WHITE VITREOUS CHINA FIXTURE WITH FAUCET LEDGE AND
<br />FRONT OVERFLOW.
<br />FAUCET; PROVIDE WITH SLOAN # ETF -600 -LT 4" CENTERSET,
<br />HARD WIRED, SENSOR OPERATED FAUCET LESS TRANSFORMER WITH
<br />"Y" STRAINER FILTERED SOLENOID VALVE AND 0.5 GPM AERATOR.
<br />TRIM: McGUIRE # 155A GRID DRAIN WITH TAILPIECE, McGUIRE
<br /># 2165CCLK LOOSE KEY COMPRESSION ANGLE STOP VALVES WITH
<br />RISERS AND ESCUTCHEONS, McGUIRE # 88872CF 1-1/4" 17 GAUGE CAST
<br />CHROME PLATED BRASS ADJUSTABLE P --TRAP AND WASTE ARM WITH
<br />CLEANOUT PLUG AND ESCUTCHEON, CONCEALED ARM CARRIER WITH
<br />STANCHIONS TO FLOOR, PLUMBEREX "PRO -EXTREME" # X-4222
<br />INSULATION KIT FOR WATER AND WASTE PIPES.
<br />DCV DUAL CHECK VALYE WITH ATMOSPHERIC,T• WATTS # SD -3,
<br />316 STAINLESS STEEL BODY, ASSE 1022 COMPLIANT, 3/8" INLET AND
<br />OUTLET, ATMOSPHERIC PORT, AND WYE PATTERN STRAINER,
<br />OD -JANITOR'S SINK: ZURN # Z-1996--24, 24" x 24" x 10" HIGH
<br />TERRAZZO BASIN WITH INTEGRAL STAINLESS STEEL DRAIN BODY.
<br />FAUCET: ZURN MODEL # 71996 -SF, 8" CENTERSET, FAUCET WITH
<br />WALL BRACE, INTEGRAL VACUUM BREAKER, PAIL HOOK AND 3/4"
<br />MALE HOSE THREADED OUTLET. SECURE FAUCET IN WALL WITH
<br />BACKBOARD,
<br />TRIM; T-35 THREE FOOT LONG REINFORCED HOSE WITH
<br />3/4" CHROME COUPLING AND WALL HOOK, # V-70 EXTRUDED VINYL
<br />BUMPER GUARD,
<br />CK)THERMOSTATIC MIXING• • VALVE: POWERS # 0480, SOLID
<br />BRASS BODY, THERMOSTATIC WAX ELEMENT, CORROSION
<br />RESISTANT INTERNAL PARTS, AND INTEGRAL CHECKS, ASSE 1070
<br />COMPLIANT, CAPABLE OF 2:.2 GPM WITH A 20 PSI DIFFERENTIAL
<br />AND A MINIMUM FLOW RATE OF 0.5 GPM. SET TEMPERATURE TO
<br />11OF FOR DUEL TEMPERATURE LAVATORIES AND HAND SINKS,
<br />100F FOR SINGLE TEMPERATURE LAVATORIES AND HAND SINKS
<br />AND 120F FOR SINKS, MOUNT BELOW THE PLUMBING FIXTURE
<br />WHERE INDICATED ! ATED ON PLAN(S),
<br />TP TRAP PRIMER: PRECISION PLUMBING PRODUCTS # PR --
<br />500 "PRIME RITE", CORROSION RESISTANT BRASS BODY, "0" RING
<br />SEALS, 1/2" INLET AND OUTLET, AND INTEGRAL VACUUM BREAKER.
<br />INSTALL THE VALVE AT A MINIMUM OF 12" ABOVE FINISHED FLOOR.
<br />PROVIDE WITH DISTRIBUTION # DU -2 FOR TWO, # DU -3 FOR THREE,
<br />OR # DU -4 FOR FOUR DRAIN CONNECTIONS.
<br />WATER PIPE SIZING CHART
<br />FIXTURE UNITS VS. PRESSURE LOSS
<br />IN PSI 1 100 FEET FOR TYPE "L" COPPER TUBE
<br />COLD WATER 5 PSI / 100
<br />HOT WATER & 5.0 PSI 1100'
<br />PIPE
<br />FLUSH TANK
<br />FLUSH VALVE
<br />VELOCITY
<br />FLOW
<br />FLUSH TANK
<br />VELOCITY
<br />FLOW
<br />SIZE
<br />SFU
<br />SFU
<br />FEET/SEC
<br />GPM
<br />SFU
<br />FEET/SEC
<br />GPM
<br />1/2"
<br />1.6
<br />NIA
<br />3.1
<br />2.4
<br />(EA)
<br />(EA)
<br />(HOT)
<br />314"
<br />6.9
<br />NIA
<br />3.9
<br />6.3
<br />2.0
<br />0.75
<br />0.75
<br />1",
<br />16
<br />WA
<br />4.7
<br />12.5
<br />1
<br />3.0
<br />3.0
<br />1-114"
<br />32
<br />4
<br />5.4
<br />22.0
<br />19.75
<br />5
<br />19.5
<br />1-1/2"
<br />59.6
<br />15.8
<br />5.9
<br />35.0
<br />44.3
<br />5
<br />27.5
<br />2"
<br />214
<br />116
<br />7.5
<br />72.0
<br />120
<br />5
<br />48
<br />2-112"
<br />476
<br />360
<br />8
<br />119.3
<br />245
<br />5
<br />74
<br />3"
<br />748
<br />700
<br />8
<br />170
<br />407.9
<br />5
<br />106.5
<br />4"
<br />1746
<br />1746
<br />8
<br />299
<br />847
<br />5
<br />186.0
<br />61'
<br />1 10300
<br />10300
<br />8 1
<br />1170.0
<br />4849
<br />1 5 1
<br />641.0
<br />SIZED WITH HAZEN WILLIAMS CONSTANT "C = 135"
<br />* UTILIZE COLD WATER SIZING
<br />CHART
<br />WATER AND WASTE FIXTURE COUNT
<br />TAG#
<br />FIXTURE/EQUIPMENT
<br />D.F.U.
<br />TOTAL
<br />HOT
<br />COLD
<br />COMBINE
<br />TOTAL
<br />TOTAL
<br />TOTAL
<br />FIXTURE TYPE new
<br />QTY
<br />(EA)
<br />D.F.U.
<br />S.F.U.
<br />S.F.U.
<br />S.F.U.
<br />S.F.U.
<br />S.F.U.
<br />SERVICE
<br />112"
<br />314"
<br />TOTAL CONNECTED LOAD = 1026 CFH
<br />BASED ON 2016 CPC TABLE 1216.2(1)
<br />(EA)
<br />(EA)
<br />(EA)
<br />(HOT)
<br />(COLD)
<br />S.F.U.
<br />LAVATORY
<br />2
<br />1.0
<br />2.0
<br />0.75
<br />0.75
<br />1.00
<br />1,5
<br />1.5
<br />2.0
<br />SERVICE SINK (MOP BASIN)
<br />1
<br />3.0
<br />3.0
<br />2.25
<br />2.25
<br />3.00
<br />2.25
<br />2.25
<br />3.D
<br />FLOOR DRAIN
<br />4
<br />2.0
<br />8.0
<br />0.00
<br />0.00
<br />0.00
<br />0
<br />0
<br />0.0
<br />WATER CLOSET (1.28 GPF FLUSH TANK)
<br />2
<br />4.0
<br />8.0
<br />0.00
<br />2.50
<br />2.50
<br />0
<br />5
<br />5.0
<br />SPECIALTY KETCHEN EQUIP.
<br />FROM FLOOR ABOVE
<br />SINK (HAND) (2" DW)
<br />2
<br />2.0
<br />4.0
<br />1.50
<br />1.50
<br />2.00
<br />3
<br />3
<br />4.0
<br />SINK (2 -COMPARTMENT) (2" IW)
<br />1
<br />3.0
<br />3.0
<br />1.50
<br />1.50
<br />2.00
<br />1,5
<br />1,5
<br />2.0
<br />SINK (3 COMPARTMENT) (2" IW)
<br />1
<br />4.0
<br />4.0
<br />3.00
<br />3.00
<br />4.00
<br />3
<br />3
<br />4.0
<br />SODA MACHINE (314" IW)
<br />1
<br />0.5
<br />0.5
<br />0.00
<br />1.00
<br />1.00
<br />0
<br />1
<br />1.0
<br />TEA MAKER (314" IW)
<br />1
<br />0.5
<br />0.5
<br />0.01)
<br />0.50
<br />0.50
<br />0
<br />0.5
<br />0.5
<br />HOT FOOD TABLE (314" IW)
<br />1
<br />0.5
<br />0.5
<br />0.75
<br />0.75
<br />1.00
<br />0.75
<br />0.75
<br />1.0
<br />DIPPER WELL (314" IW)
<br />2
<br />0.5 1
<br />1.0
<br />0.D0
<br />1 0.75 1
<br />0.75
<br />0 1
<br />1.5
<br />1 1.5
<br />TOTAL UNITS:
<br />18
<br />G NATURAL GAS (G)
<br />34.5
<br />EXISTING PIPING TO REMAIN
<br />12.00 20.00 24.00
<br />KITCHEN FIXTURE CONNECTION SCHEDULE
<br />TAG#
<br />FIXTURE/EQUIPMENT
<br />HOT
<br />WATER
<br />(IN.)
<br />COLD
<br />WATER
<br />(IN.)
<br />WASTE
<br />VENT
<br />NOTES
<br />INDIRECT
<br />DIRECT
<br />4
<br />ICE TEA DISPENSER
<br />1-114"
<br />112"
<br />314"
<br />537
<br />2"
<br />BFP, FILTERED WATER, TO FS
<br />6
<br />BEVERAGE DISPENSER
<br />OPERATING PRESSURE OF 7"WC WITH A
<br />112"
<br />314"
<br />TOTAL CONNECTED LOAD = 1026 CFH
<br />BASED ON 2016 CPC TABLE 1216.2(1)
<br />BFP, FILTERED WATER, TO FS
<br />12
<br />WALL MOUNTED HANDSINK
<br />112"
<br />112"
<br />AHU
<br />2"
<br />2"
<br />BFF
<br />15
<br />3 -COMPARTMENT FAUCET SINK
<br />314"
<br />314"
<br />(3) 2"
<br />BOP
<br />BOTTOM OF PIPE
<br />12" SWING SPOUT
<br />16
<br />2 -COMPARTMENT FAUCET SINK
<br />1/2"
<br />112"
<br />2"
<br />PRV PRESSURE REDUCING VALVE
<br />CPVC
<br />12" SWING SPOUT, TO FS
<br />18
<br />MOP SINK AND FAUCET
<br />314"
<br />3/4"
<br />DOWN
<br />3"
<br />2"
<br />INTEGRAL VACUUM BREAKER
<br />28
<br />3 -WELL WARMERS
<br />1/2"
<br />SP SUMP PUMP
<br />314"
<br />EXISTING TO REMAIN
<br />SS STAINLESS STEEL, SANITARY
<br />BFP, TO FS
<br />##
<br />CARBONATOR
<br />112"
<br />FLOOR DRAIN
<br />TDH TOTAL DYNAMIC HEAD
<br />FFA
<br />FROM FLOOR ABOVE
<br />DCV, FILTERED WATER
<br />29
<br />DIPPER WELS
<br />112"
<br />FF
<br />314"
<br />TYP TYPICAL
<br />FL
<br />TO FS
<br />37
<br />BAG -N -BOX SODA SYSTEM
<br />FULL LOAD AMPS
<br />INC.
<br />FLR
<br />FLOOR
<br />UNO UNLESS NOTED OTHERWISE
<br />4" PVC CONDUIT
<br />WCO WALL CLEANOUT: SIOUX CHIEF #873 SERIES, BRASS
<br />COUNTERSUNK PLUG, 20 GAUGE STAINLESS STEEL COVER AND
<br />SCREW. CLEANOUT TEE TO BE PROVIDED SEPARATELY. REFER
<br />TO SPECIFICATIONS FOR INSTALLATION.
<br />WHA WATER HAMMER ARRESTER: PRECISION PLUMBING
<br />PRODUCTS, HARD DRAWN COPPER BODY WITH WROUGHT
<br />COPPER FITTINGS, PISTON TYPE WITH LUBRICATED EPDM "0" RING
<br />SEALS, MEETING ASSE 1010 OR PDI WH -201. PROVIDE PDI SIZES
<br />"A" THROUGH "F" AS SHOWN ON PLANS. PROVIDE SIZE "A" UNLESS
<br />SHOWN OTHERWISE ON THE PLANS.
<br />WC FLOOR -MOUNTED ,WEER CLOSET: TQTQ #
<br />MS604114CEF TANK TYPE WHITE VITREOUS CHINA FIXTURE WITH
<br />ELONGATED BOWL, 1.28 GALLON PER FLUSH, AND CLOSE -
<br />COUPLED TANK WITH HAND TRIP LEVER INSTALLED ON WIDE SIDE
<br />OF THE STALL.
<br />IRM CHURCH # 950OSSC WHITE OPEN -FRONT
<br />CONTOURED, SOLID PLASTIC, HEAVY DUTY, SEAT LESS COVER
<br />WITH SELF --SUSTAINING CHECK HINGES AND STAINLESS STEEL
<br />BOLTS, McGUIRE # 2166CC ANGLE STOP VALVE WITH RISER AND
<br />CHROME -PLATED ESCUTCHEON.
<br />LOW PRESSURE GAS
<br />PIPE SIZING CHART
<br />PIPE
<br />LOAD (CFH)
<br />SIZE
<br />TANK SIZE
<br />112"
<br />44
<br />314"
<br />93
<br />1 "
<br />175
<br />1-114"
<br />358
<br />1-112"
<br />537
<br />2"
<br />1,034
<br />2-112"
<br />1,w
<br />OPERATING PRESSURE OF 7"WC WITH A
<br />PRESSURE DROP OF 0.5"WC
<br />TOTAL DEVELOPED LENGTH = 125 FEET
<br />TOTAL CONNECTED LOAD = 1026 CFH
<br />BASED ON 2016 CPC TABLE 1216.2(1)
<br />PLUMBING SYMBOLS
<br />ANNOTATION
<br />O1
<br />PLUMBING PLAN NOTE CALLOUT
<br />PLUMBING EQUIPMENT DESIGNATION. (CONTRACTOR FURNISHED
<br />O AND INSTALLED). REFER TO PLUMBING FIXTURE OR EQUIPMENT
<br />TANK SIZE
<br />SCHEDULES
<br />RECOVERY
<br />EQUIPMENT DESIGNATION (OWNER FURNISHED, CONTRACTOR
<br />INSTALLED, SEE KITCHEN EQUIPMENT SCHEDULE FOR
<br />MODEL#
<br />SPECIFICATIONS)
<br />RTU
<br />MECHANICAL EQUIPMENT DESIGNATION (CONTRACTOR FURNISHED
<br />1
<br />AND INSTALLED UNLESS NOTED OTHERWISE)
<br />FACTOR
<br />CONNECTION POINT OF NEW WORK TO EXISTING
<br />1
<br />DETAIL REFERENCE UPPER NUMBER INDICATES DETAIL NUMBER
<br />p1
<br />LOWER NUMBER INDICATES SHEET NUMBER
<br />ABBREVIATIONS
<br />AFF
<br />ABOVE FINISHED FLOOR
<br />MH MANHOLE
<br />AFG
<br />ABOVE FINISHED GRADE
<br />MIN MINIMUM
<br />AHU
<br />AIR HANDLING UNIT
<br />N/C NORMALLY CLOSED
<br />BFF
<br />BELOW FINISHED FLOOR
<br />N/0 NORMALLY OPEN
<br />BFG
<br />BELOW FINISHED GRADE
<br />ORD OVERFLOW ROOF DRAIN
<br />BOP
<br />BOTTOM OF PIPE
<br />PDI PLUMBING DRAINAGE INSTITUTE
<br />BQS
<br />BOTTOM OF STRUCTURE
<br />PVC POLYVINYL CHLORIDE
<br />BTU
<br />BRITISH THERMAL UNIT
<br />PRV PRESSURE REDUCING VALVE
<br />CPVC
<br />CHLORINATED POLYVINYL
<br />RD ROOF DRAIN
<br />CHLORIDE
<br />RPM REVOLUTIONS PER MINUTE
<br />DN
<br />DOWN
<br />RTU ROOFTOP UNIT
<br />DFU
<br />DRAINAGE FIXTURE UNIT
<br />SF SQUARE FEET, SUPPLY FAN
<br />DS
<br />DOWNSPOUT
<br />SP SUMP PUMP
<br />ETR
<br />EXISTING TO REMAIN
<br />SS STAINLESS STEEL, SANITARY
<br />EWC
<br />ELECTRIC WATER COOLER
<br />SEWER, SOIL STACK
<br />FD
<br />FLOOR DRAIN
<br />TDH TOTAL DYNAMIC HEAD
<br />FFA
<br />FROM FLOOR ABOVE
<br />TFA TO FLOOR ABOVE
<br />FFB
<br />FROM FLOOR BELOW
<br />TFB TO FLOOR BELOW
<br />FF
<br />FINISHED FLOOR
<br />TYP TYPICAL
<br />FL
<br />FLOW UNE
<br />UL UNDERWRITERS LABORATORIES,
<br />FLA
<br />FULL LOAD AMPS
<br />INC.
<br />FLR
<br />FLOOR
<br />UNO UNLESS NOTED OTHERWISE
<br />GPM
<br />GALLONS PER MINUTE
<br />UPS UNINTERRUPTIBLE POWER SUPPLY
<br />HD
<br />HEAD, HUB DRAIN
<br />V VOLT(S)
<br />IE
<br />INVERT ELEVATION
<br />VCP VITRIFIED CLAY PIPE
<br />IN WC
<br />INCHES OF WATER COLUMN
<br />VS VENT STACK
<br />JB
<br />JUNCTION BOX
<br />VTR VENT THROUGH ROOF
<br />J -BOX
<br />JUNCTION BOX
<br />W/ WITH
<br />kW
<br />KILOWATT
<br />MAU
<br />MAKE-UP AIR UNIT
<br />W/0 WITHOUT
<br />MAX
<br />MAXIMUM
<br />WC WATER COLUMN
<br />MBH
<br />1000 BTU PER HOUR
<br />WS WASTE STACK
<br />WSFU WATER SUPPLY FIXTURE UNIT
<br />PIPING
<br />-
<br />DOMESTIC COLD WATER (CW)
<br />--
<br />DOMESTIC HOT WATER (HW)
<br />T TRAP PRIMER LINE (T)
<br />S SOIL PIPING - ABOVE FLOOR (S)
<br />-S-- SOIL PIPING - BELOW FLOOR (S)
<br />W WASTE PIPING - ABOVE FLOOR (W)
<br />--W--
<br />WASTE PIPING - BELOW FLOOR (W)
<br />GW GREASE WASTE - ABOVE FLOOR (GW)
<br />- - --GW- -- --- GREASE WASTE -- BELOW FLOOR (GW)
<br />-- - -VBG- - - VENT BELOW GRADE (VBG)
<br />-- --• -VBF- - - VENT BELOW FLOOR (VBF)
<br />CD CONDENSATE DRAIN (CD)
<br />G NATURAL GAS (G)
<br />EXISTING PIPING TO REMAIN
<br />- - -
<br />-V- --- - - VENT PIPING (V)
<br />® SQUARE FLOOR DRAIN (FS), SIZE & TYPE
<br />ROUND FLOOR DRAIN (FD), SIZE & TYPE
<br />BALL VALVE
<br />s CONTROL VALVE
<br />SHUTOFF VALVE
<br />---�=
<br />CHECK VALVE
<br />�i� - -- -- -- UNION
<br />CAP
<br />011 WALL CLEANOUT (WCO)
<br />O FLOOR CLEANOUT (FCO)
<br />no EXTERIOR CLEANOUT (ECO)
<br />-----p
<br />ELBOW UP
<br />ELBOW DOWN
<br />TEE UP
<br />TEE DOWN
<br />--14
<br />ELBOW UP WITH SHUT-OFF VALVE (SOV)
<br />- ---+Q
<br />ELBOW DOWN WITH SHUT-OFF VALVE (SOV)
<br />0+ - -- TEE UP WITH SHUT-OFF VALVE (SOV)
<br />TEE DOWN WITH SHUT-OFF VALVE (SOV)
<br />„A„
<br />WATER HAMMER ARRESTER (WHA)
<br />WITH PDI SIZES, (A, B, C, D, & E)
<br />,,�,......_ GAS COCK
<br />TRAP PRIMER
<br />6-0-• •_••• --- TRAP PRIMER WITH DISTRIBUTION UNIT
<br />WATER HEATER SCHEDULE
<br />MANUFACTURER/
<br />AREA
<br />TANK SIZE
<br />fY
<br />RECOVERY
<br />ENERGY
<br />MARK
<br />MODEL#
<br />SERVED
<br />ENERGY SOURCE
<br />(GALLONS)
<br />INPUT
<br />80 DEGREE RISE
<br />FACTOR
<br />NOTES
<br />WHA
<br />BRADFORD WHITE ULG2PDV5OH503N
<br />KITCHEN/ LAVS
<br />NATURAL GAS
<br />48
<br />50 MBH
<br />60
<br />0.68
<br />A, B
<br />NOTES. -
<br />A,
<br />8OF TEMPERATURE RISE WITH 140F OPERATING TEMPERATURE.
<br />B.
<br />FURNISH WITH FACTORY COMBUSTION AIR INTAKE AND EXHAUST KIT
<br />d � cn
<br />�
<br />.N
<br />WLO
<br />CO
<br />Ly r I�
<br />0
<br />C7
<br />LLl ap
<br />o
<br />wCL
<br />ZD0
<br />H(D
<br />A� cq
<br />W U)
<br />Zw
<br />0
<br />THIS DRAWING IS AN INSTRUMENT OF
<br />SERVICE AND AS SUCH SHALL REMAIN
<br />THE PROPERTY OF NEPTUNE DESIGN
<br />GROUP LLC. UNAUTHORIZED USE OF
<br />REPRODUCTION WITHOUT PERMISSION
<br />OF THE ARCHITECT IS PROHIBITED. THIS
<br />DRAWING IS ONLY FOR USE IN
<br />CONNECTION WITH THIS PROJECT AND
<br />SHALL NOT BE USED FOR OTHER
<br />--LOCATIONS. COPYRIGHT 2018,
<br />Fz
<br />fY
<br />O
<br />LLJ
<br />W
<br />U
<br />�-
<br />:5
<br />G
<br />z<
<br />U
<br />-
<br />GL
<br />=
<br />�
<br />U
<br />�
<br />=
<br />o
<br />_
<br />�
<br />W
<br />o
<br />�
<br />Q
<br />aao
<br />_j
<br />r -i
<br />0
<br />'d`
<br />r-1
<br />d
<br />pe
<br />d
<br />�
<br />C�
<br />REVISION
<br />JA
<br />A
<br />3
<br />I DATE: 3.23.2018 I
<br />REVIEW SET
<br />NOT FOR
<br />PERMIT
<br />PLUMBING
<br />SCHEDULES &
<br />NOTES
<br />
|