|
SECURE PIPE
<br />HANGER TO
<br />STRUCTURE (TYP)
<br />THREADED STEEL
<br />ROD WITH NUT AND
<br />WASHER BOTH
<br />SIDES (TYP)
<br />CLEVIS HANGER,
<br />SHOWN FOR
<br />CLARITY. SIZE
<br />HANGER FOR COLD
<br />PIPE OUTSIDE
<br />DIAMETER PLUS
<br />INSULATION
<br />THICKNESS. DO NOT
<br />PENETRATE
<br />INSULATION WITH
<br />HANGER
<br />PROVIDE A SECTION
<br />OF HIGH DENSITY
<br />INSULATION OR
<br />STYROFOAM BILLETS
<br />AT EACH HANGEROF
<br />COLD INSULATED
<br />PIPE.
<br />PROVIDE SHORT
<br />INSULATION SHIELD
<br />FOR LAPPING
<br />INSULATION JACKET
<br />OVER HIGH DENSITY
<br />INSULATION OR
<br />STYROFOAM BILLETS.
<br />MAINTAIN VAPOR
<br />BARRIER
<br />M—MI9a
<br />CLEVlS HANGER,
<br />SHOWN FOR
<br />CLARITY. SIZE
<br />HANGER FOR HOT
<br />PIPE OUTSIDE
<br />DIAMETER
<br />CUT INSULATION
<br />TO FIT AROUND
<br />HANGER. SEAL
<br />EXPOSED
<br />INSULATION ENDS
<br />WITH JOINT
<br />SEALANT
<br />REFER TO SPECIFICATIONS FOR INSULATION TYPES, INSULATION THICKNESSES,
<br />HANGER TYPES, HANGER ROD CONNECTIONS TO SRUCTURE AND HANGER SPACING.
<br />INSULA
<br />NO SCALE
<br />IPE HANGER DE
<br />STUB PIPE BELOW CEILING AT LOCATIONS SHOWN ON PLAN.
<br />HANG PIPE AT HEIGHT AS REQUIRED TO ACHIEVE A 90
<br />DEGREE PENETRATION OF CEILING.
<br />PIPE HANGERS TO
<br />STRUCTURE ABOVE.
<br />LENGTH AS REQUIRED
<br />1] CEILING CEILING
<br />PROVIDE ESCUTCHEONS
<br />WHERE PIPE IS EXPOSED
<br />USE FIVE INCH SCHEDULE 40 POLYVINYLCHLORIDE (PVC) PIPING, FITTINGS
<br />AND COUPLINGS. USE MINIMUM QUANTITY OF COUPLINGS REQUIRED,
<br />SOLVENT WELD JOINTS. USE LONG SWEEP ELBOWS AT BOTH ENDS, MINIMUM
<br />TWENTY FOUR INCH RADIUS. AVOID ELBOWS IN HORIZONTAL RUN IF AT ALL
<br />POSSIBLE. PROVIDE TEST OF CONDUIT AFTER ASSEMBLY TO VERIFY
<br />WATER TIGHTNESS -- REPAIR ANY LEAKS DETECTED. MAINTAIN PRESSURE
<br />UNTIL BEVERAGE LINES ARE INSTALLED. GENERAL CONTRACTOR WILL SEAL
<br />ENDS OF CONDUIT WITH FOAM AFTER BEVERAGE LINES ARE INSTALLED IN
<br />CONDUIT.
<br />ABOVE CEI
<br />NO SCALE
<br />Cs7kIBig].rI
<br />SET TANK AS PROVIDE LOCALLY -
<br />CLOSE AS APPROVED SEISMIC
<br />POSSIBLE TO WALL. STRAPS AROUND TANK
<br />PROVIDE IN TOP AND BOTTOM
<br />NON-COMBUSTIBLE THIRDS IN SUITABLE
<br />BLOCKS FOR LOCATIONS (MINIMUM
<br />SPACERS BETWEEN 4" FROM CONTROLS).
<br />WALL AND TANK
<br />ONLY IF REQUIRED ANCHOR STRAPS
<br />FOR TANK ACCESS SECURELY TO WALL AS
<br />OR CLEARANCE. REQUIRED BY STRAP
<br />ANCHOR BLOCKS MANUFACTURER AND
<br />TO WALL AS LOCAL CODES OR
<br />REQUIRED. AUTHORITIES, BASED
<br />ON TYPE OF WALL
<br />FLOOR, EQUIPMENT CONSTRUCTION.
<br />PAD, OR SUPPORT PROVIDE BACKBOARD
<br />PLATFORM AS REQUIRED.
<br />THIS DETAIL APPLIES TO WATER HEATERS, WATER SOFTENERS,
<br />AND EXPANSION TANKS. ANCHOR TANK TO WALL AND/OR FLOOR
<br />AS REQUIRED BY CODE FOR LOCAL SEISMIC CONDITIONS.
<br />PROVIDE SEISMIC STRAPS (MEETING CODE REQUIREMENTS) AS
<br />RECOMMENDED BY MANUFACTURER FOR SIZE AND TYPE OF TANK.
<br />WATER HEATER AND EXPANSION TANK SHALL BE ANCHORED OR
<br />STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO
<br />EARTHQUAKE MOTION PER CALIFORNIA PLUMBING CODE SECTION
<br />510.5, OR OTHER LOCAL CODE AS APPLICABLE.
<br />TANK SEISMIC RESTRAINT
<br />NO SCALE
<br />INSTALL CONCENTRIC INTAKE
<br />DETAIL SHOWS GENERAL SCHEMATIC REQUIREMENTS. ADJUST TO SUIT FIELD CONDITIONS.
<br />INSTALL THROUGH ROOF OR THROUGH WALL AS SHOWN ON PLANS. REFER TO
<br />MANUFACTURER'S INSTALLATION MANUAL FOR MORE INFORMATION: MAINTAIN PROPER
<br />DISTANCES FROM EACH OTHER, AND FROM OTHER CONSTRUCTION FEATURES; VERIFY PIPE
<br />SIZE FOR MAXIMUM LENGTH OF RUN AND QUANTITY OF FITTINGS. DO NOT INSTALL BARE
<br />PVC PIPE IN AIR PATH PLENUMS: WRAP PIPE WITH FIRE -BARRIER INSULATION IF ALLOWED
<br />BY LOCAL AUTHORITIES, OR PROVIDE STAINLESS STEEL VENT PIPE, PER SPECIFICATIONS.
<br />2SEALED COMBUSTION WATER HEATER VENT
<br />NO SCALE
<br />AUTOMATIC TRAP
<br />CONNECT 1/2" PIPE (WITHOUT
<br />AND EXHAUST VENT
<br />INSTALL VENTS THROUGH
<br />SHUT-OFF VALVE IN BRANCH) TO
<br />TERMINAL FURNISHED BY
<br />ROOF OR THROUGH
<br />TRAP PRIMER VALVE OFF TOP
<br />HEATER MANUFACTURER
<br />EXTERIOR WALL AS
<br />OF COLD WATER SUPPLY OR
<br />ABOVE LOCAL MAXIMUM
<br />CONVENIENT OR AS SHOWN
<br />VALVED BRANCH PIPE.
<br />SNOW DEPTH.
<br />ON FLOOR PLAN.
<br />INSULATE PIPE UPSTREAM OF
<br />--
<br />i
<br />TRAP PRIMER, BUT NOT
<br />PROVIDE ROOF PENETRATION
<br />PIPE HANGERS
<br />DOWNSTREAM.
<br />SEALING PER SEPARATE
<br />REQUIRED BY
<br />=
<br />DETAIL.
<br />I
<br />INSTALL TRAP PRIMER LINE(S)
<br />IF ALLOWED BY CONDITIONS
<br />I
<br />DOWNSTREAM OF TRAP PRIMER
<br />AND LOCAL AUTHORITIES,
<br />i
<br />OR ABOVE EQUIPMENT.- _
<br />PROVIDE SCHEDULE 40 PVC
<br />❑
<br />d
<br />PIPE AND FITTINGS WITH
<br />SOFT COPPER TUBING. INSTALL
<br />PROVIDE DISTRIBUTION
<br />SOLVENT WELD JOINTS, PER
<br />SECURELY ATTACH TO
<br />WITHOUT KINKS, AND SLOPE
<br />SPECIFICATIONS, 3" OR 4"
<br />SHELF WITH CEILING
<br />Ii
<br />SIZE AS SHOWN ON PLANS.
<br />FLANGE, ALL -THREAD ROD,
<br />REFER TO SPECIFICATIONS
<br />AND SPLIT RING PIPEFOR
<br />DRAIN. CONCEAL PIPE(S) IN
<br />ALTERNATIVE
<br />SUPORT.
<br />INSTALLATION MATERIALS.
<br />PROVIDE 3/4" FABRICATED
<br />PRIMER VALVE.
<br />CONDENSING WATER HEATER
<br />PVC P -TRAP WITH MINIMUM
<br />n
<br />PER SPECIFICATIONS AND
<br />1 " TRAP SEAL AND 4"
<br />a
<br />SEPARATE DETAIL.
<br />LONG TAILPIECE FROM
<br />PROVIDE FLOOR DRAIN
<br />ELBOW FURNISHED WITH
<br />EXPOSED IN UNFINISHED,
<br />PROVIDE 6" HIGH
<br />WATER HEATER. -/EQUIPMENT
<br />PLATFORM.
<br />THREADED TRAP PRIMER
<br />ATTACH TO BACKBOARD
<br />CONNECTION. PROVIDE
<br />IF PIPE IS BELOW FLOOR SLAB
<br />AND --OR SUSPEND FROM
<br />r==' ON GRADE, PROVIDE 1/2"
<br />ADAPTER. BRAZE JOINT
<br />STRUCTURE ABOVE.
<br />DETAIL SHOWS GENERAL SCHEMATIC REQUIREMENTS. ADJUST TO SUIT FIELD CONDITIONS.
<br />INSTALL THROUGH ROOF OR THROUGH WALL AS SHOWN ON PLANS. REFER TO
<br />MANUFACTURER'S INSTALLATION MANUAL FOR MORE INFORMATION: MAINTAIN PROPER
<br />DISTANCES FROM EACH OTHER, AND FROM OTHER CONSTRUCTION FEATURES; VERIFY PIPE
<br />SIZE FOR MAXIMUM LENGTH OF RUN AND QUANTITY OF FITTINGS. DO NOT INSTALL BARE
<br />PVC PIPE IN AIR PATH PLENUMS: WRAP PIPE WITH FIRE -BARRIER INSULATION IF ALLOWED
<br />BY LOCAL AUTHORITIES, OR PROVIDE STAINLESS STEEL VENT PIPE, PER SPECIFICATIONS.
<br />2SEALED COMBUSTION WATER HEATER VENT
<br />NO SCALE
<br />AUTOMATIC TRAP
<br />CONNECT 1/2" PIPE (WITHOUT
<br />PRIMER VALVE WITH
<br />�T-�
<br />SHUT-OFF VALVE IN BRANCH) TO
<br />INTEGRAL AIR GAP.
<br />i1i
<br />TRAP PRIMER VALVE OFF TOP
<br />INSTALL TRAP PRIMER
<br />I
<br />OF COLD WATER SUPPLY OR
<br />MINIMUM 12" ABOVE
<br />CEILING SPACE
<br />VALVED BRANCH PIPE.
<br />FLOOR FOR EVERY 20'
<br />I
<br />INSULATE PIPE UPSTREAM OF
<br />OF DISCHARGE PIPE.
<br />i
<br />TRAP PRIMER, BUT NOT
<br />AND SIZE OF BRANCH
<br />AND AT LOCATION
<br />DOWNSTREAM.
<br />IF TRAP PRIMER IS
<br />REQUIRED BY
<br />=
<br />INSTALLED IN PARTITION,
<br />I
<br />INSTALL TRAP PRIMER LINE(S)
<br />PROVIDE ACCESS DOOR
<br />I
<br />DOWNSTREAM OF TRAP PRIMER
<br />PER SPECIFICATIONS,
<br />i
<br />OR ABOVE EQUIPMENT.- _
<br />OR DISTRIBUTION UNIT USING 1/2"
<br />❑
<br />d
<br />11
<br />I
<br />SOFT COPPER TUBING. INSTALL
<br />PROVIDE DISTRIBUTION
<br />i
<br />i1i
<br />WITHOUT KINKS, AND SLOPE
<br />UNIT(S) WHERE MORE
<br />I
<br />I
<br />Ii
<br />CONTINUOUSLY TOWARDS FLOOR
<br />THAN ONE TRAP IS
<br />d"
<br />e -H
<br />DRAIN. CONCEAL PIPE(S) IN
<br />SERVED BY ONE TRAP
<br />PARTITION OR CHASE IN
<br />PRIMER VALVE.
<br />I
<br />n
<br />FINISHED AREAS. TRAP PRIMER
<br />a
<br />a
<br />AND PIPES MAY BE INSTALLED
<br />PROVIDE FLOOR DRAIN
<br />d
<br />EXPOSED IN UNFINISHED,
<br />BODY OR P -TRAP WITH
<br />�s
<br />NON-PUBLIC AREAS.
<br />THREADED TRAP PRIMER
<br />d
<br />CONNECTION. PROVIDE
<br />IF PIPE IS BELOW FLOOR SLAB
<br />SWEAT TO THREADED
<br />r==' ON GRADE, PROVIDE 1/2"
<br />ADAPTER. BRAZE JOINT
<br />ELASTOMERIC INSULATION FROM
<br />BELOW FLOOR SLAB ON
<br />PRIMER CONNECTION TO 1"
<br />GRADE.
<br />ABOVE FLOOR SLAB.
<br />PROVIDE TRAP PRIMERS WHERE SHOWN ON FLOOR PLANS, AND WHERE REQUIRED
<br />BY LOCAL AUTHORITIES. PIPING ARRANGEMENT SHOWN IS SCHEMATIC: ADJUST
<br />TO SWT FIELD CONDITIONS. REFER
<br />TO SPECIFICATIONS AND PLUMBING FIXTURE
<br />SCHEDULE FOR MORE INFORMATION.
<br />INSTALL TRAP PRIMER VALVE AND
<br />DISTRIBUTION UNIT PER MANUFACTURER'S RECOMMENDATIONS.
<br />('r—'N� TRAP PRIMER
<br />IN/OU_T_WALL
<br />NO SCALE
<br />3/4" PIPE FROM
<br />COLD WATER SUPPLY
<br />TO WATER HEATER,
<br />WITH NO CHECK
<br />VALVES INTERVENING
<br />FDA -COMPLIANT
<br />BUTYL DIAPHRAGM
<br />WELDED STEEL
<br />EXPANSION TANK WITH
<br />POLYPROPYLENE LINING,
<br />NSF APROVED FOR
<br />DOMESTIC WATER
<br />SERVICE
<br />PIPE HANGER
<br />NEXT TO ELBOW
<br />X i-- PROVIDE
<br />DIELECTRIC PIPE
<br />UNION AT TANK
<br />CONNECTION FOR
<br />CONNECTION OF
<br />DISSIMILAR METALS
<br />AIR CHARGING
<br />VALVE. FILL TANK
<br />WITH AIR PRESSURE
<br />TO MATCH WATER
<br />PRESSURE.
<br />PIPING ARRANGEMENT SHOWN IS SCHEMATIC. ADJUST TO
<br />SUIT FIELD CONDITIONS. FOLLOW MANUFACTURER'S
<br />INSTRUCTIONS FOR INSTALLATION PROCEDURE. VERIFY
<br />PROPER OPERATION WHEN INSTALLED, PROVIDE SEISMIC
<br />STRAP OR BRACING WHEN REQUIRED BY LOCAL AUTHORITIES.
<br />3 SMALL EXPANSION TANK
<br />NO SCALE
<br />INSTALL WITH MINIMUM 6"
<br />CLEARANCE TO BUILDING
<br />STRUCTURE ABOVE
<br />PROVIIDE THERMOMETER IN
<br />TEE FITTING
<br />HOT WATER TO FIXTURES
<br />PIPE UNIONS (TYPICAL) ABOVE TOP
<br />OF TANK (TO FACILITATE REMOVAL
<br />OF WATER HEATER) -a
<br />PROVIDE DIELECTRIC PIPE UNION AT
<br />TANK CONNECTION FOR CONNECTION
<br />OF DISSIMILAR METALS (TYPICAL)
<br />PROVIDE 12"WIDE x 12"DEEP HEAT
<br />TRAP AT INLET AND OUTLET (TYPICAL)—
<br />LINE SIZE GAS SUPPLY TO
<br />WATER HEATER
<br />GAS-FIRED WATER HEATER PER
<br />SPECIFICATIONS AND SCHEDULE /
<br />GAS COCK -' /
<br />UNION WITH GROUND JOINT J
<br />6" LONG DIRT LEG --`*'�
<br />PROVIDE REDUCER AT EQUIPMENT
<br />CONNECTION IF REQUIRED
<br />PROVIDE PLATFORM.
<br />ATTACH TO BACKBOARD
<br />AND/OR SUSPEND FROM
<br />STRUCTURE ABOVE, MINIMUM
<br />6" CLEAR OF CEILING, IF ANY
<br />SUSPEND PIPE FROM
<br />ESCUTCHEON AT
<br />STRUCTURE ABOVE,
<br />CEILING PENETRATION
<br />NOT FROM HOOD OR
<br />CEILING
<br />GAS COCK
<br />DO NOT INSTALL
<br />INSTALL AUTOMATIC
<br />ANY GAS VALVES IN
<br />GAS SHUT-OFF VALVE
<br />CEILING SPACE
<br />FURNISHED WITH
<br />wCoLU
<br />EXHAUST HOOD FIRE
<br />EXHAUST HOOD
<br />SUPPRESSION SYSTEM
<br />PROVIDE QUANTITY
<br />PIPE DROP OF SIZE
<br />AND SIZE OF BRANCH
<br />AND AT LOCATION
<br />CONNECTIONS AS
<br />SHOWN ON PLAN
<br />REQUIRED BY
<br />=
<br />EQUIPMENT SERVED.
<br />GAS PIPE HEADER ALONG
<br />PROVIDE GAS COCK
<br />WALL BEHIND COOKING
<br />LOCATED WHERE
<br />EQUIPMENT (OR INSIDE
<br />ACCESSIBLE BESIDE
<br />WALL IF INDICATED ON
<br />OR ABOVE EQUIPMENT.- _
<br />PLAN), SIZES AS SHOWN
<br />-• i ON PLANS
<br />INSTALL FLEXIBLE
<br />APPLIANCE �\-6" DIRT LEG AT BOTTOM
<br />CONNECTOR HOSE OF RISER
<br />FURNISHED WITH
<br />KITCHEN EQUIPMENT CONNECT HOSE TO
<br />KITCHEN EQUIPMENT
<br />KITCHEN FLOOR---� - (TYPICAL)
<br />REFER TO SPECIFICATIONS FOR MORE INFORMATION ABOUT PIPE, FITTINGS,
<br />AND CONNECTIONS. PIPING ARRANGEMENT SHOWN IS SCHEMATIC; ADJUST
<br />TO SUIT FIELD CONDITIONS. IF EXPOSED, ATTACH RISER AND HEADER TO
<br />WALL WITH 1" CLEARANCE BEHIND PIPE (UNLESS INSTALLED INSIDE WALL
<br />AS SHOWN ON PLANS). MAKE FINAL CONNECTION TO EQUIPMENT AS
<br />RECOMMENDED BY MANUFACTURER. INSTALL ANY GAS PRESSURE
<br />REGULATORS FURNISHED BY FOOD SERVICE EQUIPMENT CONTRACTOR.
<br />7 COOKING APPLIANCE GAS PIPE
<br />NO SCALE
<br />N E
<br />©
<br />04 Lo m
<br />co "T O
<br />PROVIDE AUTOMATIC VACUUM e2 °E �
<br />.
<br />RELIEF VALVE ABOVE TOP >LL- W LL-
<br />OF TANK ¢ ¢ -0
<br />nLL ----- -TYPICAL SHUT-OFF VALVE Z Lo a
<br />f I Lu - -- - COLD WATER SUPPLY
<br />TO WATER HEATER W p N CD
<br />CHECK VALVE
<br />COLD WATER BRANCH °O
<br />TO EXPANSION TANK
<br />Lo
<br />-- INSTALL ASME TEMPERATURE AND cfl
<br />PRESSURE RELIEF VALVE FURNISHED
<br />WITH WATER HEATER SET TO OPEN AT
<br />NOT MORE THAN 150 PSI.
<br />CONNECT TO TOP OR SIDE OF
<br />TANK AS REQUIRED FOR 0
<br />MODEL FURNISHED (TYPICAL)
<br />PROVIDE HARD COPPER RELIEF VALVE C]
<br />DISCHARGE PIPE FULL SIZE OF VALVE
<br />OUTLET. DRAIN PIPE SHALL DRAIN INTO + z
<br />MOP SINK. DRAIN PIPE SHALL TERMINATE w
<br />A MAXIMUM OF 6 INCHES ABOVE THE MOP
<br />7 SINK, U)
<br />INSTALL DRAIN VALVE W❑
<br />FURNISHED WITH
<br />WATER HEATER
<br />REFER TO SPECIFICATIONS, SCHEDULES AND NOTES FOR MORE INFORMATION. PIPING ARRANGEMENT
<br />SHOWN IS SCHEMATIC. ADJUST TO SUIT FIELD CONDITIONS. VERIFY CONNECTION SIZES AND
<br />LOCATIONS PER MANUFACTURER'S REQUIREMENTS. REFER TO FLOOR PLANS FOR PIPE SIZES.
<br />PROVIDE SEISMIC STRAP OR BRACING IF/AS REQUIRED BY LOCAL AUTHORITIES AND/OR SEPARATE
<br />DETAIL. INSTALL WITH BOTTOM MINIMUM 6'-6" ABOVE FLOOR IF ABOVE JANITOR'S SINK; OTHERWISE
<br />HIGH AS POSSIBLE. PLATFORM SHALL BE PLYWOOD ON UNISTRUT FRAME BRACKETED AND
<br />ANCHORED TO WALL, AND/OR SUSPENDED FROM STRUCTURE ABOVE WITH THREADED ROD. POWER
<br />WIRING AND DISCONNECT SWITCH ARE SPECIFIED BY ELECTRICAL. INTERLOCK OF AQUASTAT WITH
<br />RECIRCULATION PUMP IS SPECIFIED BY ELECTRICAL IF REQUIRED.
<br />4 GAS FIRED WATER HEATER OVERHEAD
<br />NO SCALE
<br />ROOF INSULATION
<br />CORE DRILL ROOF OR
<br />PROVIDE SLEEVE IF
<br />REQUIRED BY TYPE
<br />OF ROOF DECK.
<br />PROVIDE FIRE STOP
<br />SEAL BETWEEN PIPE
<br />AND SLEEVE OR
<br />DECK.
<br />PROVIDE PIPE INCREASER ON
<br />SMALLER VENT IF/WHERE
<br />CODE REQUIRES A MINIMUM
<br />3" VENT THRU ROOF
<br />MINIMUM 12" ABOVE ROOF
<br />NORMALLY. EXTEND TO
<br />HEIGHT OF PARAPET WHEN
<br />WITHIN 10' OF PARAPET,
<br />OR ABOVE MAXIMUM LOCAL
<br />SNOW DEPTH.
<br />ANCHOR PIPE
<br />TO STRUCTURE.
<br />ROOF DECK
<br />MINIMUM 12"
<br />BELOW ROOF
<br />REFER TO SPECIFICATIONS
<br />FOR TYPE OF PIPE,
<br />FITTINGS, AND CONNECTORS.
<br />REFER TO PLANS FOR
<br />SIZE(S) AND LOCATION(S).
<br />LOCATE VTR MINIMUM THREE FEET FROM PROPERTY LINE, TEN FEET
<br />HORIZONTAL OR THREE FEET VERTICAL ABOVE ANY BUILDING
<br />OPENING OR FRESH AIR INTAKE, TWENTY FIVE FEET FROM ANY
<br />OPENING OR FRESH AIR INTAKE IN MEDICAL FACILITIES AND ONE
<br />FOOT FROM ANY VERTICAL SURFACE. REFER TO LOCAL CODES
<br />FOR OTHER VENT TERMINATION REQUIREMENTS. LOCATE VTR
<br />MINIMUM 18" FROM ADJACENT WALL, PARAPET, EXPANSION JOINT,
<br />ROOF DRAIN, EQUIPMENT CURB, OR OTHER ROOF FEATURE.
<br />OFFSET IN CEILING SPACE WHERE REQUIRED TO MEET THESE
<br />CONDITIONS. INSULATE LAST SIX FEET OF VENT PIPE INSIDE
<br />BUILDING PER SPECIFICATIONS.
<br />VENT TH RU ROOF "VTR"}
<br />NO SCALE
<br />THIS DRAWING IS AN INSTRUMENT OF
<br />SERVICE AND AS SUCH SHALL REMAIN
<br />THE PROPERTY OF NEPTUNE DESIGN
<br />GROUP LLC. UNAUTHORIZED USE OF
<br />REPRODUCTION WITHOUT PERMOSION
<br />OF THE ARCHITECT iS PROHIBITED. THIS
<br />DRAWING IS ONLY FOR USE 1N
<br />CONNECTION WITH THIS PROJECT AND
<br />SHALL NOT SE USED FOR OTHER
<br />LOCATIONS. COPYRIGHT 2018.
<br />REVISION
<br />IA I
<br />A
<br />DATE: 3.23.2018 1
<br />REVIEW SET
<br />NOT FOR
<br />PERMIT
<br />PLUMBING
<br />DETAILS
<br />ci
<br />w
<br />w
<br />0
<br />z
<br />❑
<br />wCoLU
<br />V
<br />F-
<br />2
<br />Z
<br />H
<br />w
<br />V
<br />acncQ©
<br />=
<br />V
<br />0<ow-1
<br />=
<br />Ln
<br />Q
<br />w
<br />❑
<br />d
<br />C)
<br />o
<br />d"
<br />e -H
<br />Q
<br />v
<br />n
<br />a
<br />a
<br />d
<br />�s
<br />�
<br />d
<br />0
<br />REVISION
<br />IA I
<br />A
<br />DATE: 3.23.2018 1
<br />REVIEW SET
<br />NOT FOR
<br />PERMIT
<br />PLUMBING
<br />DETAILS
<br />
|