|
GENERAL NEW NOTES:
<br />1. PRIOR TO SUBMITTING BID, VISIT THE JOB SITE AND BECOME FULLY ACQUAINTED WITH
<br />THE EXISTING CONDITIONS OF THE PROJECT. REVIEW THE GENERAL NOTES,
<br />SPECIFICATIONS AND OTHER DRAWINGS FOR ADDITIONAL REQUIREMENTS WHICH MAY
<br />NOT BE SPECIFICALLY CALLED OUT IN THIS PORTION OF THE CONSTRUCTION
<br />DOCUMENTS. NOTIFY ARCHITECT, ENGINEER AND/OR OWNER OF CONFLICTS OR
<br />DISCREPANCIES PRIOR TO SUBMISSION OF BID.
<br />2. COORDINATE THE INSTALLATION OF THE MECHANICAL SYSTEMS WITH OTHER TRADES TO
<br />ENSURE A NEAT AND ORDERLY INSTALLATION. INSTALL DUCTWORK AS TIGHT TO
<br />STRUCTURE AS POSSIBLE. COORDINATE WITH OTHER TRADES TO AVOID CONFLICTS.
<br />COORDINATE INSTALLATION OF DUCTWORK TO AVOID CONFLICTS WITH ELECTRICAL
<br />PANELS, LIGHTING FIXTURES, ETC. ANY MODIFICATIONS REQUIRED DUE TO LACK OF
<br />COORDINATION WILL BE THE RESPONSIBILITY OF THE CONTRACTOR AT NO EXTRA COST
<br />TO THE OWNER.
<br />3. NEW MECHANICAL EQUIPMENT AND DUCTWORK ARE SHOWN AT APPROXIMATE
<br />LOCATIONS. FIELD MEASURE FINAL DUCTWORK LOCATIONS PRIOR TO FABRICATION AND
<br />MAKE ADJUSTMENTS AS REQUIRED TO FIT THE DUCTWORK AND PIPING WITHIN THE
<br />AVAILABLE SPACE. VERIFY THAT FINAL EQUIPMENT LOCATIONS MEET MANUFACTURERS
<br />RECOMMENDATIONS REGARDING SERVICE CLEARANCE AND PROPER AIRFLOW
<br />CLEARANCE AROUND EQUIPMENT.
<br />4. REFER TO ARCHITECTURAL DRAWINGS FOR RELATED CONSTRUCTION DETAILS AS
<br />APPLICABLE TO THE HVAC SYSTEM. VERIFY CHASES AND PENETRATIONS SHOWN ON
<br />ARCHITECTURAL DRAWINGS THAT ARE INTENDED FOR DUCTWORK AND PIPING MEET
<br />REQUIREMENTS.
<br />5. COORDINATE LOCATION OF ROOF MOUNTED HVAC EQUIPMENT AND ROOF
<br />PENETRATIONS WITH THE ARCHITECTURAL AND STRUCTURAL DRAWINGS.
<br />6. INDOOR AIR QUALITY MEASURES: PROTECT INSIDE OF (INSTALLED AND DELIVERED)
<br />DUCTWORK AND HVAC UNITS FROM EXPOSURE TO DUST, DIRT, PAINT AND MOISTURE.
<br />REPLACE INSULATION THAT HAS GOTTEN WET AT ANY TIME DURING CONSTRUCTION,
<br />DRYING THE INSULATION IS NOT ACCEPTABLE. SEAL ANY TEARS OR JOINTS OF
<br />INTERNAL FIBERGLASS INSULATION. REMOVE DEBRIS FROM CEILING/RETURN AIR
<br />PLENUM INCLUDING DUST. AN INDEPENDENT, PROFESSIONAL DUCT CLEANING
<br />COMPANY SHALL VACUUM CLEAN ANY DUCTWORK CONNECTED TO MVAC UNITS THAT
<br />WERE OPERATED DURING THE CONSTRUCTION PERIOD AFTER NEW FILTERS, MINIMUM
<br />MERV-8, ARE INSTALLED AND PRIOR TO TURNING SYSTEM OVER TO THE OWNER.
<br />7. INSTALL DUCTWORK PARALLEL TO BUILDING COLUMN LINES UNLESS OTHERWISE SHOWN
<br />OR NOTED.
<br />8. OVERHEAD HANGERS AND SUPPORTS FOR EQUIPMENT, DUCTWORK SHALL BE
<br />FASTENED TO BUILDING JOISTS OR BEAMS. DO NOT ATTACH HANGERS AND SUPPORTS
<br />TO THE ABOVE FLOOR SLAB OR ROOF EXCEPT WHERE CONCRETE INSERTS IN
<br />CONCRETE SLABS ARE ALLOWED BY THE SPECIFICATIONS.
<br />9. COORDINATE LOCATION OF EQUIPMENT SUPPORTS WITH LOCATION OF EQUIPMENT
<br />ACCESS PANELS/DOORS TO ENABLE SERVICE OF EQUIPMENT AND/OR FILTER
<br />REPLACEMENT.
<br />10. SEAL PENETRATIONS THROUGH THE BUILDING COMPONENTS IN ACCORDANCE WITH THE
<br />CONTRACT SPECIFICATIONS. FIREPROOF PENETRATIONS THROUGH FIRE RATED
<br />COMPONENTS IN ACCORDANCE WITH U.L. REQUIREMENTS.
<br />11. COORDINATE THE EXACT MOUNTING SIZE AND FRAME TYPE OF DIFFUSERS, REGISTERS
<br />AND GRILLES WITH THE SUPPLIER TO MEET THE CEILING, WALL AND DUCT INSTALLATION
<br />REQUIREMENTS.
<br />12. ADJUST LOCATION OF CEILING DIFFUSERS, REGISTERS AND GRILLES AS REQUIRED TO
<br />ACCOMMODATE FINAL CEILING GRID AND LIGHTING LOCATIONS.
<br />13. LOCATE AND SET THERMOSTATS SENSORS AT LOCATIONS SHOWN ON PLANS. VERIFY
<br />EXACT LOCATIONS WITH ARCHITECT PRIOR TO INSTALLATION. INSTALL THERMOSTATS
<br />WITH TOP OF DEVICE AT MAXIMUM 48" AFF TO MEET ADA REQUIREMENTS UNLESS
<br />NOTED OTHERWISE ON PLANS. INSTALL WIRING IN CONDUIT PROVIDED BY DIVISION 16.
<br />14. PROVIDE A MANUAL BALANCING DAMPER IN EACH BRANCH DUCT TAKEOFF FROM MAIN
<br />SUPPLY, RETURN, OUTDOOR AND EXHAUST AIR DUCTS.
<br />15. PROVIDE A PREFABRICATED 45 DEGREE, HIGH EFFICIENCY, RECTANGULAR/ROUND
<br />BRANCH DUCT TAKEOFF FITTING WITH MANUAL BALANCING DAMPER AND LOCKING
<br />QUADRANT FOR BRANCH DUCT CONNECTIONS AND TAKE -OFFS TO INDIVIDUAL
<br />DIFFUSERS, REGISTERS AND GRILLES.
<br />16. BRANCH DUCTWORK TO AIR OUTLETS SHALL BE SAME SIZE AS OUTLET NECK SIZE
<br />UNLESS OTHERWISE NOTED.
<br />17. RIGID DUCTWORK INSULATION: PROVIDE 3/4 LB DENSITY, 2-1/2" (R-8) THICK, INSULATION
<br />WRAP ON RIGID ROUND, CONCEALED, SUPPLY AND RETURN AIR DUCTS. PROVIDE 2" (R--
<br />8) THICK 1-1/2 LB DENSITY INTERNAL DUCT LINER ON RECTANGULAR SUPPLY AND
<br />RETURN AIR DUCTS. DUCT SIZES ON MECHANICAL PLANS INDICATE CLEAR INSIDE
<br />AIRFLOW DIMENSIONS, INCREASE SHEET METAL SIZES ACCORDINGLY.
<br />18. PROVIDE THERMAFLEX TYPE M -KE, FLEXMASTER TYPE 8, OR APPROVED EQUAL
<br />FLEXIBLE DUCTWORK. FLEXIBLE DUCTWORK SHALL BE LISTED UNDER UL 181 AS CLASS
<br />1 AIR DUCT AND BE PROVIDED WITH INTEGRAL R-8, 3/4 LB DENSITY FIBERGLASS
<br />INSULATION. FLEXIBLE DUCTWORK SHALL NOT EXCEED 5'-0" IN LENGTH AND SHALL BE
<br />INSTALLED AND SUPPORTED TO AVOID SHARP BENDS AND SAGGING.
<br />19. PROVIDE TYPE I GREASE HOOD EXHAUST DUCTWORK OF MINIMUM 16 GAUGE BLACK
<br />IRON WITH LIQUID WELDS WITH ACCESS PANELS FOR GREASE CLEANING AS REQUIRED
<br />BY NFPA 96 AND LOCAL CODES. DUCT SHALL BE WRAPPED IN TWO LAYERS OF 3M, 20A
<br />FIRE BARRIER DUCT WRAP. SLOPE DUCT BACK TOWARDS HOOD AT MINIMUM OF 1/4"
<br />PER LINEAR FOOT DUCT WRAP SYSTEM SHALL MEET UL REQUIREMENTS FOR GREASE
<br />DUCT ENCLOSURES.
<br />20. THE HVAC, REFRIGERATION, AND FIRE SUPPRESSION SYSTEM SHALL NOT CONTAIN CFC
<br />OR HALONS.
<br />21. ALL DUCT AND OTHER RELATED AIR DISTRIBUTION COMPONENTS SHALL BE COVERED
<br />WITH TAPE, PLASTIC, OR SHEET METAL UNTIL FINAL STARTUP OF THE HEATING, COOLING
<br />AND VENTILATING EQUIPMENT.
<br />22. IF THE NEW HVAC SYSTEM IS USED DURING CONSTRUCTION, USE RETURN AIR FILTERS
<br />WITH A MERV OF 8. REPLACE ALL FILTERS IMMEDIATELY PRIOR TO OCCUPANCY.
<br />23. AN OPERATION & SYSTEM MANUAL SHALL BE PROVIDED TO THE FIELD INSPECTOR AT
<br />THE TIME OF FINAL INSPECTIONS.
<br />24. REFER TO MECHANICAL SPECIFICATIONS, SHEET M4, FOR HVAC SYSTEM CONTROLS,
<br />SPECIFICATIONS AND TEST & BALANCE REQUIREMENTS. FINAL SYSTEM TESTING,
<br />BALANCING AND ADJUSTMENTS SHALL BE PERFORMED BY A CONTRACTOR CERTIFIED
<br />BY THE NATIONAL ENVIRONMENTAL BALANCING BUREAU (NEBB) OR ASSOCIATED AIR
<br />BALANCE COUNCIL (AABC).
<br />25. A FINAL REPORT FOR TESTING AND ADJUSTING OF ALL NEW SYSTEMS SHALL BE
<br />COMPLETED AND PROVIDED TO THE FIELD INSPECTOR PRIOR TO FINAL APPROVAL. THIS
<br />REPORT SHALL BE SIGNED BY THE INDIVIDUAL RESPONSIBLE FOR PERFORMING THESE
<br />SERVICES.
<br />OUTSIDE AIR REQUIREMENTS
<br />GRILLE, REGISTER AND DIFFUSER SCHEDULE
<br />GROSS
<br />FLOOR
<br />AREA
<br />(SQ. FT)
<br />CODE OUTSIDE AIR
<br />REQUIREMENTS
<br />MARK
<br />MANUFACTURER
<br />MODEL
<br />FACE
<br />MOUNTING
<br />FACE SIZE
<br />MAX.
<br />MAX. PRESS.
<br />NOTES
<br />RTU -1
<br />1,000
<br />EAT
<br />EF -1
<br />TYPE
<br />LOCATION
<br />IN
<br />INC
<br />DROP IN. W. C.)
<br />44
<br />660
<br />CD -1
<br />TITUS
<br />TMS
<br />CONE
<br />LAY -IN
<br />2424
<br />30
<br />0.05
<br />A-E
<br />RTU -1
<br />CD -2
<br />TITUS
<br />PAR
<br />CONE
<br />GYP.
<br />12x12
<br />30
<br />0.05
<br />A-E
<br />MAU-2
<br />CD -3
<br />TITUS
<br />TMR
<br />ROUND
<br />DUCT
<br />-
<br />30
<br />0.05
<br />A D
<br />1,550 TOTAL = 203 705
<br />CD -4
<br />TITUS
<br />TMS
<br />CONE
<br />GYP.
<br />24)24
<br />30
<br />0.05
<br />A -F
<br />51.9
<br />RG -1
<br />TITUS
<br />PAR
<br />PERFORATED
<br />GYP.
<br />2424
<br />30
<br />0.05
<br />A-E
<br />C. INTERLOCK MAKEUP AIR UNIT (MAU-2) W/ EXHAUST FAN (KEF-2) TO ENERGIZE SUPPLY FANS WHEN EXHAUST FANS ARE ACTIVATED.
<br />RG -2
<br />TITUS
<br />350FL
<br />LOWERED
<br />WALL
<br />NECK + 1-3/4
<br />25
<br />0.1
<br />A,C,D
<br />NOTES:
<br />1140
<br />A.
<br />NECK SIZE SHOWN ON DRAWINGS. PROVIDE NECK FOR DUCT CONNECTION.
<br />-
<br />B.
<br />4 -WAY THROW PATTERN UNLESS OTHERWISE SHOWN ON DRAWINGS.
<br />NOTES:
<br />C.
<br />BRANCH DUCT SIZE SHALL BE SAME AS NECK SIZE UNLESS OTHERWISE SHOWN ON DRAWINGS.
<br />D.
<br />BAKED ENAMEL FINISH, WHITE TO MATCH CEILING COLOR.
<br />C. INTERLOCK KEF-1 WITH KITCHEN COOKING EQUIPMENT UNDER HOOD #1, MAKE-UP AIR UNIT (MAU-1) AND ROOF TOP UNIT (RTU -1).
<br />E.
<br />FRAME TYPE TO MATCH CEILING CONSTRUCTION, COORDINATE WITH ARCHITECTURAL RCP.
<br />F.
<br />PROVIDE WITH OPPOSED BLADE DAMPER ACCESSIBLE FROM DIFFUSER FACE.
<br />WITH INTEGRAL BIRDSCREEN AND BACKDRAFT DAMPER.
<br />OUTSIDE AIR REQUIREMENTS
<br />AREA
<br />PURPOSE
<br />GROSS
<br />FLOOR
<br />AREA
<br />(SQ. FT)
<br />CODE OUTSIDE AIR
<br />REQUIREMENTS
<br />EXHAUST
<br />(CFM)
<br />SYSTEM
<br />NUMBER
<br />ACTUAL
<br />OUTSIDE AIR
<br />CFM PER UNI
<br />CFM PER
<br />SQ. FT
<br />CFM
<br />REQD.
<br />CFM PER
<br />PERSON
<br />NO. OF
<br />PEOPLE
<br />CFM
<br />REQD,
<br />KITCHEN HOOD
<br />RTU -1
<br />1,000
<br />EAT
<br />EF -1
<br />DINING
<br />770
<br />0.15
<br />116
<br />15
<br />44
<br />660
<br />75
<br />5,000
<br />PREP/SERVICE
<br />580
<br />0.15
<br />87
<br />15
<br />3
<br />45
<br />RTU -1
<br />DINING/KITCHEN
<br />COOKING AREA
<br />200
<br />-
<br />-
<br />-
<br />-
<br />-
<br />100.0%
<br />MAU-2
<br />KITCHEN
<br />2,290
<br />2,290
<br />100,0%
<br />TOTAL AIRFLOW
<br />8,090 5,090
<br />62.9%
<br />TOTAL POSITIVE AIR FLOW
<br />PERCENT POSITIVE AIR FLOW
<br />90
<br />1.8%
<br />1,550 TOTAL = 203 705
<br />TOTAL = 1,000
<br />AIR BALANCE SCHEDULE
<br />EXHAUST
<br />EQUIPMEN
<br />AREA/EQUI PMENT
<br />SERVED
<br />MODEL
<br />EXHAUST
<br />(CFM)
<br />TOTALS
<br />(CFM)
<br />KEF-1
<br />KITCHEN HOOD
<br />WEIGHT
<br />1800
<br />FAN
<br />KEF-2
<br />KITCHEN HOOD
<br />ESP
<br />3050
<br />EAT
<br />EF -1
<br />RESTROOM
<br />FLA
<br />75
<br />MIN
<br />HP
<br />EF -2
<br />RESTROOM
<br />LBS
<br />75
<br />5,000
<br />OUTDOOR A
<br />EQUIPMEN
<br />AREA/EQUIPMENT
<br />SERVED
<br />SUPPLY AIR
<br />(CFM)
<br />DESIGN
<br />OA (CFM)
<br />PERCENT
<br />OA/SA
<br />HP
<br />5,090
<br />RTU -1
<br />DINING/KITCHEN
<br />4,000
<br />1,000
<br />25.0%
<br />MAU-1
<br />KITCHEN
<br />1,800
<br />1,800
<br />100.0%
<br />MAU-2
<br />KITCHEN
<br />2,290
<br />2,290
<br />100,0%
<br />TOTAL AIRFLOW
<br />8,090 5,090
<br />62.9%
<br />TOTAL POSITIVE AIR FLOW
<br />PERCENT POSITIVE AIR FLOW
<br />90
<br />1.8%
<br />MAKEUP AIR UNIT SCHEDULE
<br />MARK
<br />MANUFACTURER
<br />MODEL
<br />AREA
<br />SUPPLY FAN
<br />EVAPORATIVE COOLING
<br />ELECTRICAL
<br />WEIGHT
<br />NOTES
<br />FAN
<br />CFM
<br />MIN.
<br />ESP
<br />CAP
<br />EAT
<br />LAT
<br />V/PH
<br />FLA
<br />CFM
<br />MIN
<br />HP
<br />(IN)
<br />SERVED
<br />LBS
<br />RPM
<br />V/PH
<br />FLA
<br />DISC. TYPE
<br />LBS
<br />TYPE
<br />KEF-1
<br />HP
<br />IN
<br />MBH
<br />DB/WB
<br />DB/WB
<br />0.80
<br />DIRECT
<br />0.8
<br />1100
<br />MAU-1
<br />CAPTIVE-AIRE
<br />EA -Al -G10
<br />KITCHEN
<br />FC
<br />1800
<br />1.00
<br />0.5
<br />40.8
<br />95165
<br />74165
<br />20811
<br />4.9
<br />368
<br />A,B
<br />MAU-2
<br />CAPTIVE -A
<br />-G10
<br />KITCHEN
<br />FC
<br />2290
<br />1.00
<br />0.5
<br />51.9
<br />95/65
<br />74165
<br />208/1
<br />4.9
<br />1 449
<br />A,C
<br />NOTES:
<br />A. REFER TO CAPTIVE-AIRE DRAWINGS FOR SPECIFICATIONS, SCHEDULE SHOWN FOR REFERENCE ONLY
<br />B. INTERLOCK MAKEUP AIR UNIT (MAU-1) Wl EXHAUST FAN (KEF-1) TO ENERGIZE SUPPLY FANS WHEN EXHAUST FANS ARE ACTIVATED.
<br />C. INTERLOCK MAKEUP AIR UNIT (MAU-2) W/ EXHAUST FAN (KEF-2) TO ENERGIZE SUPPLY FANS WHEN EXHAUST FANS ARE ACTIVATED.
<br />FAN SCHEDULE
<br />(NATURAL GAS
<br />MARK
<br />SERVICE
<br />MANUFACTURER
<br />MOUNTING
<br />MODEL
<br />CFM
<br />ESP
<br />DRIVE
<br />MIN.
<br />FAN
<br />ELECTRICAL
<br />WEIGHT
<br />NOTES
<br />V/PH
<br />(EA, RA, SA)
<br />NOTES
<br />FAN
<br />TYPE
<br />CFM
<br />MIN
<br />HP
<br />(IN)
<br />(BELT/DIRECT)
<br />HP
<br />RPM
<br />V/PH
<br />FLA
<br />DISC. TYPE
<br />LBS
<br />MIN. NO,
<br />STAGES
<br />KEF-1
<br />EXHAUST
<br />CAPTIVE-AIRE
<br />ROOF
<br />EABDUI5
<br />1800
<br />0.80
<br />DIRECT
<br />0.8
<br />1100
<br />208/1
<br />3.7
<br />FUSED
<br />142
<br />A -C
<br />KEF-2
<br />EXHAUST
<br />CAPTIVE-AIRE
<br />ROOF
<br />EABDU24HP
<br />3050
<br />1.25
<br />DIRECT
<br />1.5
<br />847
<br />20811
<br />7.5
<br />FUSED
<br />231
<br />A,B,D
<br />EF -1
<br />EXHAUST
<br />GREENHECK
<br />CEILING
<br />SP -13110
<br />75
<br />0.2
<br />DIRECT
<br />80W
<br />1140
<br />12011
<br />-
<br />-
<br />-
<br />E -G
<br />EF -2
<br />I EXHAUST
<br />I. GREENHECK
<br />CEILING
<br />SP -8110
<br />75
<br />0.2
<br />DIRECT
<br />80W
<br />1140
<br />12011
<br />-
<br />-
<br />-
<br />E -G
<br />NOTES:
<br />A. REFER TO CAPTIVE-AIRE DRAWINGS FOR SPECIFICATIONS, SCHEDULE SHOWN FOR REFERENCE ONLY
<br />B. DIVISION 16 CONTRACTOR TO FURNISH DISCONNECT SWITCH.
<br />60 O
<br />C. INTERLOCK KEF-1 WITH KITCHEN COOKING EQUIPMENT UNDER HOOD #1, MAKE-UP AIR UNIT (MAU-1) AND ROOF TOP UNIT (RTU -1).
<br />D. INTERLOCK KEF-2 WITH KITCHEN COOKING EQUIPMENT UNDER HOOD #2, MAKE-UP AIR UNIT (MAU-2) AND ROOF TOP UNIT (RTU -1).
<br />E. MANUFACTURER TO PROVIDE 8" HIGH ROOF CURB AND MODEL GRS-08 SPUN ALUMINUM ROOF CAP
<br />WITH INTEGRAL BIRDSCREEN AND BACKDRAFT DAMPER.
<br />F. PROVIDE RUBBER IN SHEAR ISOLATION AND ALL -THREAD HANGING RODS.
<br />G. INTERLOCK FAN OPERATION WITH RESTROOM LIGHT SWITCH.
<br />EXISTING TO REMAIN ROOFTOP UNIT SCHEDULE
<br />(NATURAL GAS
<br />HEAT)
<br />MARK
<br />MANUFACTURER
<br />MODEL
<br />SUPPLY FAN
<br />COOLING COIL
<br />HEAT EXCHANGER
<br />MIN.
<br />0/A
<br />CFM
<br />MIN.
<br />EER
<br />MCA
<br />MOCP
<br />V/PH
<br />WEIGHT
<br />LBS
<br />NOTES
<br />FAN
<br />TYPE
<br />CFM
<br />MIN
<br />HP
<br />ESP
<br />IN
<br />REFR.
<br />TYPE
<br />TH
<br />MBH
<br />SH
<br />MBH
<br />EAT LAT
<br />MIN. OUTPUT
<br />MBH
<br />MIN. EFF.
<br />%
<br />NOM. INPUTI
<br />MBH
<br />MIN. NO,
<br />STAGES
<br />LAT
<br />DL(FI
<br />DB
<br />WB DB
<br />WB
<br />RTU -1
<br />TRANE
<br />YHC120
<br />FC
<br />4,000
<br />3.00
<br />1.25
<br />R -410A
<br />119.8
<br />92.5
<br />79.0
<br />65.0
<br />56.0
<br />55.0
<br />120
<br />450
<br />80
<br />150
<br />2
<br />90
<br />1000
<br />12.4
<br />46.1
<br />60
<br />20813
<br />2200
<br />A -C
<br />NOTES:
<br />A. EXISTING 7 -DAY PROGRAMMABLE THERMOSTAT WITH STAGED HEATING AND COOLING CAPABILITY AS REQUIRED FOR OPERATION OF HEATING AND COOLING CONTROLS.
<br />B. PROVIDE 2", MERV-8 PLEATED THROWAWAY AIR FILTERS.
<br />C. EXISTING TO REMAIN SMOKE DETECTOR LOCATED IN THE SUPPLY DUCT DROP.
<br />(:D
<br />MECHANICAL FLOOR PLAN
<br />SCALE: 1/4"=V-0"
<br />ti
<br />0
<br />CN
<br />c; I
<br />O C3 U
<br />N Lo c-
<br />00 `T O
<br />�CD
<br />Q-w-i LL_ as
<br />Lo
<br />Lu
<br />W U) u?
<br />U N C
<br />ill 00
<br />CL
<br />THIS DRAWING IS AN INSTRUMENT OF
<br />SERVICE AND AS SUCH SHALT. REMAIN
<br />THE PROPERTY OF NEPTUNE DESIGN
<br />GROUP LLC. UNAUTHORIZED USE OF
<br />REPRODUCTION WITHOUT PERMISSION
<br />OF THE ARCHITECT IS PROHIBITED. THIS
<br />DRAWING }S ONLY FOR USE IN
<br />CONNECTION WITH THIS PROJECT AND
<br />SHALL NOT BE USED FOR OTHER
<br />LOCATIONS. COPYRIGHT 2018,
<br />Lu
<br />W
<br />o
<br />�
<br />z❑z
<br />W
<br />m
<br />W
<br />U
<br />I."`
<br />2
<br />z
<br />Lu H
<br />=
<br />u
<br />-
<br />1200
<br />U
<br /><
<br />.�.;
<br />a_
<br />O
<br />c
<br />0
<br />_
<br />❑
<br />Q
<br />W
<br />CD -1
<br />°-
<br />0
<br />o
<br />J
<br />r-1
<br />0
<br />450
<br />d"
<br />ri
<br />a
<br />o
<br />a
<br />O
<br />4
<br />C�
<br />Oa
<br />2
<br />d
<br />d
<br />60 O
<br />-2
<br />7
<br />LE
<br />77
<br />104
<br />CD -1
<br />60
<br />450
<br />CD -2
<br />-
<br />75
<br />O
<br />-O
<br />RTU-
<br />4
<br />7 �IF
<br />((E
<br />14
<br />rxl
<br />11
<br />M2
<br />irI
<br />I �
<br />I �
<br />I � �
<br />I O ' 3
<br />100 i e------
<br />CD-3
<br />2501 KTYP)
<br />6
<br />1
<br />3
<br />14x12
<br />�oEl
<br />I
<br />I
<br />I
<br />I
<br />I
<br />100
<br />CD -4
<br />400
<br />I
<br />I
<br />I
<br />I
<br />I
<br />I d"
<br />I � .
<br />I x
<br />0 I co
<br />3
<br />O -]
<br />I f
<br />I
<br />I
<br />I
<br />18x16
<br />I
<br />I
<br />I
<br />I a
<br />100
<br />_ CD -4 r__�------- __
<br />1 OI O O O
<br />400 1
<br />04
<br />20x14
<br />18x16
<br />I
<br />I
<br />140
<br />OI O O O
<br />L----------- ----__---__ _ ___--- _ _ ___
<br />FA
<br />n
<br />RG -1 O
<br />®42x18
<br />® (D G o
<br />0
<br />0
<br />c
<br />100 1100
<br />CD -3 ® CD 3 °
<br />a 400
<br />L - _1- 400
<br />Q 1 • I
<br />I I o
<br />I I
<br />I F -i I
<br />a © 0 0
<br />I I
<br />oG (D o
<br />I � I
<br />I I
<br />(TYP) I
<br />n 9 L ------ --I o
<br />104 100
<br />p CD -3 CD -3 0
<br />425 425
<br />(D G
<br />oIL
<br />I F
<br />- RTUI-1 I -
<br />I 7
<br />� I- --;r--- �---- ____-- +
<br />�-�-.-----.-A
<br />` 5
<br />I
<br />Ll
<br />I
<br />I
<br />(:D
<br />MECHANICAL FLOOR PLAN
<br />SCALE: 1/4"=V-0"
<br />ti
<br />0
<br />CN
<br />c; I
<br />O C3 U
<br />N Lo c-
<br />00 `T O
<br />�CD
<br />Q-w-i LL_ as
<br />Lo
<br />Lu
<br />W U) u?
<br />U N C
<br />ill 00
<br />CL
<br />THIS DRAWING IS AN INSTRUMENT OF
<br />SERVICE AND AS SUCH SHALT. REMAIN
<br />THE PROPERTY OF NEPTUNE DESIGN
<br />GROUP LLC. UNAUTHORIZED USE OF
<br />REPRODUCTION WITHOUT PERMISSION
<br />OF THE ARCHITECT IS PROHIBITED. THIS
<br />DRAWING }S ONLY FOR USE IN
<br />CONNECTION WITH THIS PROJECT AND
<br />SHALL NOT BE USED FOR OTHER
<br />LOCATIONS. COPYRIGHT 2018,
<br />1 REVISION
<br />1 DATE:3.23.2018
<br />REVIEW SET
<br />NOT FOR
<br />PERMIT
<br />MECHANICAL
<br />FLOOR PLAN &
<br />SCHEDULES
<br />m 1
<br />Lu
<br />W
<br />o
<br />�
<br />z❑z
<br />W
<br />m
<br />W
<br />U
<br />I."`
<br />2
<br />z
<br />Lu H
<br />=
<br />u
<br />-
<br />U
<br /><
<br />.�.;
<br />a_
<br />O
<br />c
<br />0
<br />_
<br />❑
<br />Q
<br />W
<br />°-
<br />0
<br />o
<br />J
<br />r-1
<br />0
<br />d"
<br />ri
<br />a
<br />o
<br />a
<br />O
<br />4
<br />C�
<br />Oa
<br />d
<br />d
<br />d
<br />1 REVISION
<br />1 DATE:3.23.2018
<br />REVIEW SET
<br />NOT FOR
<br />PERMIT
<br />MECHANICAL
<br />FLOOR PLAN &
<br />SCHEDULES
<br />m 1
<br />
|