|
OPW Installation, Operation, and Maintenance Manual, Page 46 Executive Order VR-1 02-1
<br /> Step 19:Electronic Liquid Level Monitoring materials and workmanship for a period of one year from the date
<br /> If an electronic level monitor is installed, it must be of manufacture by OPW(ECO products two years from date of
<br /> manufacture.)Proof of purchase may be required. As the
<br /> calibrated to match the top of the 61 SO valve body,
<br /> exclusive remedy under this limited warranty,OPW,will at its sole
<br /> which must correlate with 95%of the actual tank discretion,repair,replace,or issue credit for future orders for any
<br /> Capacity. product that may prove defective within the one year date of
<br /> manufacture period(repairs,replacements,or credits may be
<br /> PREVENTATIVE MAINTENANCE subject to prorated warranty for remainder of the original warranty
<br /> period,complete proper warranty claim documentation required.)
<br /> Annually, inspect the flapper in the 61 SO to see that This warranty shall not apply to any product that has been altered
<br /> It is open by looking down the drop tube opening, in any way,which has been repaired by any party other than a
<br /> Test the 61 SO drop tube seals with CARB service representative authorized by OPW,orwhen failure is due
<br /> to misuse,or improper installation or maintenance. OPW shall
<br /> procedure TP-201.11D. if the drop tube seal passes
<br /> have no liability whatsoever for special,incidental or
<br /> testing, no further maintenance is required. If the consequential damages to any party,and shall have no liability for
<br /> drop tube falls testing, replace the drop tube seal the cost of labor,freight,excavation,clean up,downtime,
<br /> with OPW P/N: H11931 M for 4"Tubes. Re-test the removal,reinstallation,loss of profit,or any other cost or charges.
<br /> 61 SO drop tube with CARE procedure TP-201.1 D. For any product certified to California 2001 standards,OPW
<br /> warrants that product sold by it are free from defects in material
<br /> If this does not correct the leak the 61 SO needs to and workmanship for a period of one year from date of
<br /> be replaced. manufacture or one year from date of registration of installation
<br /> not to exceed 15 months from date of manufacture by OPW.
<br /> THIS WARRANTY IS IN LIEU OF ALL OTHER
<br /> CAUTION: Do not insert any foreign object into drop WARRANTIES,EXPRESS OR IMPLIED,AND SPECIFICALLY
<br /> tube if flapper is in the closed position.For example a THE WARRANTIES OF MERCHANTABILITY AND FITNESS
<br /> tank level measuring stick. This will damage the valve FOR A PARTICULAR PURPOSE. THERE ARE NO
<br /> and void the Warranty. ALWAYS check flapper WARRANTIES,WHICH EXTEND BEYOND THE DESCRIPTION
<br /> location before"sticking"the tank. If flapper is in the ON THE FACE HEREOF.
<br /> closed position the tank is either over filled and you
<br /> need to wait until the liquid level goes down or the
<br /> 61 SO is damaged and needs to be replaced.
<br /> 61SO Performance Specifications:
<br /> This Overfill Prevention Valve has been
<br /> manufactured and tested to, and met,the following
<br /> California specifications. Performance Requirement:
<br /> Leak rate to be less than or equal to 0.17 CFH @
<br /> 2.0"W.C.
<br /> Torque Specification:
<br /> Self-Clinching Studs, 5/16-8 UN thread, 11.5 ft-lbs
<br /> minimum to 13.5 ft-lbs maximum.
<br /> Important:Leave these installation instructions
<br /> and maintenance procedures with the station ;•,,
<br /> operator.
<br /> Notice:OPW products must be used in compliance with
<br /> applicable federal,state,and local laws and regulations. Product Manufacture:"OPW'
<br /> selection should be based on physical specifications and Model:61SO-4"
<br /> limitations and compatibility with the environment and material to (4"Represents Size)
<br /> be handled. All illustrations and specifications in this literature are Manufacture Date:
<br /> based on the latest production information available at the time of "MFG MM YY"
<br /> publication. Prices,materials,and specification are subject to MM=Month YY=Year
<br /> change at any time,and models may be discontinued at any time,
<br /> in either case,without notice or obligation. Product Identification
<br /> Standard Product Warranty
<br /> OPW warrants that products sold by it are free from defects in
<br /> C>
<br /> A r--�Compow
<br /> P.O. Box 405003"Cincinnati,Ohio 45240-5002
<br /> 1-800-422-2525 Domestically,513-870-3315 Internationally
<br /> www.opw-fc.com
<br /> Copyright,2007-OPW Fueling Components Inc.,Cincinnati,OH
<br /> Printed in U.S.A.p/n H14790PA Rev.B-5/07
<br /> OPUV 61 SO Overfill Prevention Valve Page 8
<br />
|