|
MSDS 19-2
<br /> July 1, 2002
<br /> Steps to be taken in case material s released or spilled: Solubility in water NIL
<br /> Ventilate area. Remove sou ces of ignition.Prevent skin and eye Vapor Density Heavier than air
<br /> contact and breathing of vap r. If the material contains,or is mixed Approx. boiling range(°C) No Data Available
<br /> with an isocyanate activator/ ardener:Wear a positive-pressure, Approx.freezing range(°C) -92--59°(C)
<br /> supplied-air respirator(NI05 approved TC-19C),eye protection, Gallon weight(lbs./gal) 7.60- 10.40
<br /> gloves and protective clothin Pour liquid decontamination solution Specific gravity 0.91- 1.25
<br /> over the spill and allow to sit it least 10 minutes. Typical Percent volatile by volume 69.45- 85.00
<br /> decontamination solutions for isocyanate containing materials are: Percent volatile by weight 48.18- 78.17
<br /> 20%Surfactant (Tergitol TMI 1 10)and 80%Water OR 0-10% Percent solids by volume 15.00- 30.55
<br /> Ammonia,2-5%Detergent ar d Water(balance) Pressure can be Percent solids by weight 21.83- 51.82
<br /> generated.Do not seal waste containers for 48 hours to allow CO2 to
<br /> vent. After 48 hours,materia may be sealed and disposed of SECTION 10-Stability and Reactivity
<br /> properly. If material does no contain or is not mixed with an Stability:
<br /> isocyanate activator/hardene Wear a properly fitted air purifying Stable
<br /> eye protection,gloves and pr ective clothing. Confine,
<br /> with organic vapor artridges(NIOSH approved TC-23C), Incompatibility(materials to avoid):
<br /> fine,remove with water,alcohols,amines
<br /> inert absorbent,and dispose f properly. Hazardous decomposition products:
<br /> CO,CO2,smoke,and oxides of any heavy metals that are reported in
<br /> SECTION 7-Han ling and Storage "Composition,Information on Ingredients"section.
<br /> Hazardous polymerization:
<br /> Precautions to be taken in handlingnd storing: Will not occur.
<br /> Observe label precautions.If c mbustible(flashpoint between 100- Sensitivity to static discharge:
<br /> 2001F),keep away from heat, parks and flame.If flammable For flammable materials(flashpoint less than 100°F)and
<br /> (flashpoint less than 100°F),al o keep away from static combustibles(flashpoint between 100-200°F)if heated above the
<br /> discharges and other sources o ignition.If material is extremely Flashpoint,solvent vapors in air may explode if static grounding and
<br /> flammable(flashpoint less tha 20°F)or flammable,VAPORS MAY bonding is not used during transfer of this product.
<br /> IGNITE EXPLOSIVELY OR CAU4E FLASH FIRE,respectively.Vapors Sensitivity to mechanical impact:
<br /> may spread long distances.PreVent buildup of vapors.Close container Not Applicable
<br /> after each use.Ground contain rs when pouring.Wash thoroughly
<br /> after handling and before eatin�or smoking.Do not store above SECTION 11-Additional Information
<br /> 120°F. If product is waterbase�l,do not freeze.
<br /> Other precautions: PRODUCT CODE INGREDIENTS(Product Specific)
<br /> If material is a coating:do notand,flame cut,braze or weld dry
<br /> coating without a NIOSH appro4ed respirator or appropriate 23947K"" Acetone,Acrylic Polymer,Butyl Acetate,Carbon Black(0.6%),Cab
<br /> ventilation,and gloves. (3.3%),Ethylbenzene(2.1-5.2%*@),Polyester Resin,Polyethylene/Vinyl
<br /> SECTION 8-Exposure Con is or Personal Protection Acetate,Titanium Dioxide/Aluminum Hydrate/Amorphous Silica,Xylene
<br /> Engineering controls and work practils: GAL MIT:8.44 T PCT SOLIDS:33.94 VOL PCT SOLIDS:22.26
<br /> Ventilation: SOLVENT DENSITY:7.18 VOC LE: 5.5 VOC AP: 4.9
<br /> Provide sufficient ventilation in volume and pattern to keep FLASH POINT:20*F to below 73*F H:2 F:3 R:0 OSHA STORAGE:IA
<br /> contaminants below applicable e�c TSCA STATUS:In compliance PHOTOCHEMICALLY REACTIVE:YES
<br /> pp posure limits.
<br /> Respiratory:
<br /> Do not breathe vapors or mists. If this product contains
<br /> isocyanates or is used with an is cyanate activator/hardener,wear a 53381(rM Acetone,Acrylic Polymer,Amorphous Silica,Butyl Acetate,Cab
<br /> positive-pressure,supplied-air re pirator(NIOSH approved TC-19C) (3.0%),Ethylbenzene(3.4%*@),Polyester Resin,Polyethylene/Vinyl Acetate,
<br /> while mixing activator/hardener ith paint,during application and Titanium Dioxide,Xylene(18-21%*@)
<br /> until all vapors and spray mist a exhausted. If product does not GAL WT:9.18 WT PCT SOLIDS:40.62 VOL PCT SOLIDS:24.28
<br /> contain or is not mixed with an i cyanate activator/hardener,a SOLVENT DENSITY:7.21 VOC LE: 5.3 VOC AP: 4.8
<br /> properly fitted air purifying respi for with organic vapor FLASH POINT:20°F to below 730F H:2 F:3 R.,0 OSHA STORAGE:IB
<br /> cartridges(NIOSH TC-23C)and articulate filter(NIOSH TC-84A)may Tom►STATUS:In compliance PHOTOCHEMICALLY REACTIVE:YES
<br /> be used. Follow respirator manu cturer s directions for respirator
<br /> use.Do not permit anyone witho t protection in the painting area.
<br /> Individuals with history of lung o breathing problems or prior 99KTN Acrylic Polymer, Butyl Acetate,Carbon Black(2.4%),Cab(4.0%),
<br /> reaction to isocyanates should no use or be exposed vapor or spray Ethylbenzene(0.9%*@),Hexyl Acetate Isomers,Methyl Ethyl Ketone(13%*@),
<br /> mist if product contains or is mix d with isocyanate Toluene(24%*@),Xylene(9-10%*@)
<br /> activators/hardeners. GAL WT:7.81 WT PCT SOLIDS:32.10 VOL PCT SOLIDS:25.74
<br /> Protective clothing: SOLVENT DENSITY:7.14 VOC LE: 5.3 VOC AP: 5.3
<br /> Neoprene gloves and coveralls ar recommended. FLASH POINT:20*F to below 73*F H:2 F:3 R:0 OSHA STORAGE:IB
<br /> Eye protection: TSCA STATUS:In compliance PHOTOCHEMICALLY REACTIVE:YES
<br /> Desirable in all industrial situation .Goggles are preferred to
<br /> prevent eye irritation. If safety asses are substituted,include
<br /> splash guard or side shields. nN
<br /> 68139K Acetone,Acrylic Polymer,Butyl Acetate,Carbon Black(0.4%),Cab
<br /> (3.5%),Ethylbenzene(2.1-5.3%*@), Phthalocyanine Blue(1%*), Polyester
<br /> SECTION 9-Physical and�bemical Properties
<br /> Resin,Polyethylene/Vinyl Acetate,Titanium Dioxide/Aluminum
<br /> Evaporation Rate Hydrate/Amorphous Silica,Xylene(25-28%*@)
<br /> P Slower than Ether
<br /> 6
<br /> MSDS 19-2
<br /> July 1,2002
<br /> © 2001-2002 E.I. du Pont de Nemours and Company.All rights reserved. Reproduction or translation of any part of this
<br /> work beyond that permitted by U.S. copyright laws without
<br /> the written permission of du Pont is unlawful and strictly forbidden
<br />
|