Laserfiche WebLink
LEADING THE NVAY IN FUELING INNOVATION WORLDWIDE <br /> Specifying the Proper Length 53VML or 30MV OPW 53VML and 30MV <br /> Series Ball Moat Ball Float Sizing / OPW • <br /> ---- -- 89 Extractor Wrench <br /> Step 1: Tank Ullage Calculator :• <br /> Determine Dimension"X": Consult ♦30 minutes x 5GPM = 150 gallons IMPORTANT <br /> I the tank chart(provided by the tank <br /> manufacturer)to determine the •Ullage compression rate*is 27% after <br /> distance that corresponds to 10%of the ball seats Installing the incorrect length OPW <br /> the total tank capacity for 53VML ♦ 150 gallons_.73(1—ullage 53VML or 30MV Ball Float Vent Valve <br /> or 308 gallons for 30MV. compression rate)=205.48 gallons for your specific application may result in • <br /> Step 2: ♦205.48 x 1.5(OPW recommended delivery flow restriction at levels exceeding <br /> Determine Dimension"Y": Measure the safety factor)=308.22 gallons requirements established by the U.S. <br /> dimension from the inside top of the ♦Approximately 308 gallons required EPA. Always consult the appropriate <br /> tank to the top of the 4"threaded tank ullage tank charts and determine the specifics <br /> "bung"fitting. *tillage compression rate will vary your our tank installation to determine the <br /> Step 3: with head pressure. appropriate length OPW 53VML or 30MV. <br /> Add measurements"X"and"Y". The illustration and instructions below <br /> Then subtract 1/4"and round up to are intended to serve as a guide <br /> the nearest length ball float. in this determination. <br /> Tank Manway Mounted Extractor Tank Top Mounted Extractor <br /> 1-2100-EVR Spill t 1-2100-EVR Spill <br /> Container , Container <br /> e s •• a 'u o <br /> 4 ° <br /> 17117 Vapor \ 1711T Vapor <br /> Recovery Cap i Recovery Cap <br /> 400 Series, 233 Series, 61VSA-1020EVR Vapor <br /> 1611 Series Vapor Face Seal Adaptor <br /> p / i Extractor Fitting Recovery Adaptor <br /> Recovery Adaptor <br /> 233 Series, <br /> Extractor Fitting <br /> 400 Series, <br /> _... To Tank _ ; Face Seal Adaptor <br /> Vents <br /> _ _ To-Tank <br /> Vents <br /> Y �x ��53V_M_ <br /> L X or 30MV,Ball — 53VML or 30MV,Ball <br /> Float Vent Valve � _ Float V ng t Vale <br /> Materials OPW 89 Extractor Wrench <br /> Pipe extra heavy black iron The OPW 89 Extractor Wrench is designed to install or remove <br /> Handle and Hook:ductile iron 89 j OPW 53VML and 30MV Ball Float Vent Valves or OPW 233VP <br /> and 233VMP Test Plugs in OPW 233, 233V, and 233VM Extractor <br /> Fittings. The 89 is also designed to work with the cage assemblies <br /> Ordering specifications &Z on the 233E Suction Tube Extractor Fitting and 88E Extractable <br /> Product# in. mm lbs, kg Angle Check Valve in suction system applications.The 89 wrench <br /> 89.0044 _z 51 3 6.84 consists of a 4 foot section of pipe welded to a"T"handle with either <br /> V12"or 2"hook section. Both the V/2°and 2"hook sections mate <br /> ize Wrench roduct Compatible <br /> current OPW ball floats and extractable cages;the V/2"model is <br /> P <br /> designed for some discontinued OPW products. <br /> 89.0044 33E,88E Series <br /> OPW Environmental Systems 0 <br />