Laserfiche WebLink
Primary Piping System Installation <br /> TABLE 6. Adhesive Kit Data <br /> 7000&8000 Series <br /> - For Petroleum Products in all Piping Systems <br /> - For Petroleum Products,Alcohols,and Alcohol-Gasoline Mixtures <br /> Approx.No.of Bonds per Kit Working <br /> Label 2' 3' 4' Ufe(l) <br /> Kit(2) Color Coding(4) Quantity Mixed Adhesive (50 mm) (75 mm) (100 mm) (Min.) <br /> 7014 Red 6.8 oz.(193 g) 25 18 10 25 <br /> 7024(twin pack) Black 2.5 oz.ea.(71 g ea.) 18 10 6 25 <br /> 7069(3) Blue 9.95 oz.(282 g) — — — 25 <br /> 8014 Green 6.4 oz.(181 g) 21 16 8 15 <br /> 8024(twin park) Yellow 2.7 oz.ea.(77 g ea.) 18 12 7 15 <br /> 8055(bag kit) No Color 1.6 oz.(45 g) 6 4 2 15 <br /> 8069(3) Orange 9.3 oz(264 g) — — — 15 <br /> (1)Working life is the time it takes a properly mixed (2)Solvent does not come with the adhesive kits;it cause of the large quantity of adhesive per kit.Use <br /> can of adhesive to"set up"at 75°F. Number of must be ordered separately. with secondary containment only. <br /> bonds is based on the volume in the kit and must be (3)Not recommended for 2",3",and 4"(50 mm,75 (4)Base adhesive&hardener are color-coded to <br /> completed within the working life of the kit. mm,and 100 mm)primary pipe installations be- assure proper mixing. <br /> ADHESIVE WORKING LIFE <br /> Working life or pot life is the time it takes for the adhesive <br /> to harden in the mixing can. This time is measured from the <br /> time the adhesive and hardener are first mixed. Working life ADHESIVE DISPOSAL:Once the adhesive and hardener have <br /> is shorter at temperatures above 7 °F( 1°C)and be- been mixed and reacted,nothing can be extracted,and it is <br /> comes longer as the temperature drops below 75*F classified as non-hazardous material.Dispose of in a normal <br /> (211C). Working life is affected by the quantity of mixed ad- manner as other solid waste.Excess adhesive and hardener can <br /> be mixed,allowed to react,and disposed of as above.If extra jars <br /> hesive as well as by temperature. Use the following methods of adhesive or hardener have accumulated without the other com- <br /> to increase the working life of adhesives: ponent to mix and react, contact your Smith Fibercast <br /> regional manager.Hardener jars,when empty are not subject to <br /> EPA regulation and can be disposed of in a normal manner. <br /> Warm Weather: These guidelines are based on federal regulations.State and lo- <br /> a. Occasionally stir the adhesive mixture during applica- cal regulations and ordinances should be reviewed. <br /> ton. <br /> b. Use small ice chests or other containers used with <br /> freezer packs to keep adhesive cool. <br /> Cool Weather: <br /> a. Store adhesive kits inside. <br /> b. Prewarm to between 70'-80°F before use. <br /> CAUTION: If adhesive becomes warm and starts to <br /> harden In the container,discard Immediately. DO NOT <br /> ■ USE THIS ADHESIVE TO BOND A JOINT! <br /> When adhesive is allowed to harden in the metal <br /> container,the container may reach approximately <br /> ■ 400°F(2050C). Do not handle hot containers with- <br /> out heavy gloves. This exothermic reaction will generate <br /> a dense,foul-smelling smoke. Therefore,place the con- <br /> tainer outdoors In an open area until It cools. Avoid in- <br /> haling smoke. <br /> RED THREAD IIA Pipe & Fittings 8 <br />