COMPLIANCE INFO_2010-2012 - Laserfiche WebLink

Home Browse Search

` . "Hard Angle repair Instructions For any "Hard Angle" Conduit Repair Kit For Existing Conduit pipe from 1/2"to 1.5"OD in Direct Burial Application repairs Page 2 STEP 5:Seal around the old boot&pipe l You must Sealeny Open 1 Seal around the existing boot &pipe if needed. I I spaces between the pipe Apply a thick bead of an approved sealer between the old boot&the pipe, i as needed to fill any cracks or openings. &Old Boot' i'is x S.mast r1 ._ , c ,.?s.a"�_ ..stalk;{g.f82'.rr*,3'3e.. 3x .i:. z STEP 6: Install The Repair Boot&Insert If the Bonding Ring is used,DO THIS PART 11t: ` apply a thick bead of Zi -T or DBF 16 all around the sealing surface of the Bonding Ring Use this step If the studs I Slide the Bonding Ring over the over the studs&press firmly to the sump wall from the original fitting Start here if the Bonding Ring is not used or after the Bonding Ring is in place against the sump wall: I were LEFT IN PLACE Apply a thick bead of Zila-Tite or DBF 11 all around the sealing surface of the repair boot Slide the repair boot over the studs with the fill ,n3rt at tt f-tr;ts lstall tile=ian e Nut —Do o!`Jc t over�i�f:ter�_ -Sr1ut Es elc a- Install the Insert&Clamp • Apply r ioTite to the out surface of the Insert&press into the end of the repair boot Set the Clamp over the pipe end of the repair boot. 'A2� STEP 6A: Install The Repair Boot&Insert � .._-.• �----�-. ,�..--.•-�-•-.••w-•-- If the Bonding Ring is used,DO THIS PART 11t: Use this step if the studs _ Apply a thick bead of Zirs-rite or DBF St all around the sealing surface of the Bonding Ring xr'�c 'I Slide &Position the Bonding Ring up to&press firmly to the sump wall m I from the original fitting I a were REMOVED. _ Start here if the Bonding Ring is not used or after the Bonding Ring is in place against the sump wall: • Apply a thick bead of Z,i _Tite or DBF it all around ther sealing surface of the repair boot Slide the repair boot up to the sump wall or up to the Bonding Ring with the f€l! o t;t tt p Install the Insert&Clamp q Apply 7aTite to the out surface of the Insert&press into the end of the repair boot • Set the Clamp over the pipe end of the repair boot. A111111111116— Step 7: Fill With DBF II,Insert Fill Plug TC3C3L5 ft t1iRE PRODUCTS NEEDED` Assemble DAG&DBF II(see instructions on DPM website). Gloves and Static Mixer DBC Cleaner • Purge 1-2 oz. 7/16"Nut driver (for flange nuts) Zip-Tite Bonder • Fill fitting slowly. 5/16" Nut driver (for Band Clamps) DBF II Polysulfide Liquid Fill • Insert fill plug when filling is completed. DAG Caulk Gun (for DBF II) DAGP Caulk Gun (Pneumatic version for DBF II) Paas in licit: n • Repair Boot,Split URBKZ C45 x x (to match pipe size) Clean any spilled DBF II with DBC and dispose FILL Volu of remaining products per instructions local requirements. s e° (per re air kttsc�`} 2 clamps 1#72,1#xx(to match parts) Volume of DBF II needed = 4 oz for 1",5 oz for W pipe Fill Port Plug RFA xPlug Notes t1se,I';errao ft Fill option if access is)united Volume of Zip-Tite needed = 1/2 Oz Repair Instructions Volume of DBB V needed = 13 ML Note: After 1 hour the mpaia job may beyrires-static tested Diversified Products Manufacturing Inc. 5523 Baggett Marysville Road,Oroville,CA 95965 530-534-3966 www.dpm-llc.com