COMPLIANCE INFO_1995-1999 - Laserfiche WebLink

Home Browse Search

�J NOTE: Your tank will arrive with a Quick Disconnect aSS8016 ;C-- `cure 2-3 00) unless you have a liquid -filled interstitial space canis. It th : V -11I is not conngured as shown in the illustration prior to pre-insmlationw.niir^g, he Xerxes Coorcinator at the plant nearest you or the Technical "ces Department at Xerxes' headquarters. QUICK DISCONNECT ASSEMBLY NOTE: In order to test the primary tank alone, the :est hose) Ttsac NoT ie connected to the service fitting - keep the nylon tie in place. PRIMARY (INTERNAL) TANK TEST 1. Connect the test manifold to an available serviWEl'1ltting. Remove the remaining fittings, redope, and re6e—=t litm plugs. 2. Pressurize the primary tank to 5 PSIG: add or SVrcve air a.s necessary and allow the pressure to stabilize. :s.athe vaave on the test manifold supply line. 3. Monitor the pressure for one hour. Soap test ai :9s10 a flogs and manways. Watch for active air bubbles wttl;. indicat~a leak. ______, NYLON TIE i �—pgESSI�tE REL:.. I:TcY1C_ \ ?OM C01P�°aaF1R 9UICK DISCONNECT /'-AIR i�9'�.Y vAL/E ASSEMBLY AIR'. , ;AUvrt MONITOR FITTING ^=: "rnlo SECONDARY (EXTERNAL) TANK TESM 1. Maintain the pressure in the primary tank 2. Free the hose from the service fitting by cattinc Ul. milon I e. 3. Insert the hose into the Quick Disconnect chem- `-eve (fob at the top of the service fitting). This Mil allow airmetlaransw tom the primary to secondary tank 4. Pressurize to 5 PSIG. Add or remove air via "!! Qiy valve as needed and allow the pressure to 3-Miiize. ase fire VAve on :he test manifold. Disconnect the air supplyiit . 5. Monitor the pressure for one hour. Soap the ease, exterior of the rank and watch for active air bubbles which ,,mdcme a ,eak. When the test is complete, carefully release the sk zre=refrom the *ank by opening the supply valve. i ne air sup=r* "inti alreWY shouic have been disconnected. When ate air flow -vrm ate supply valve stops, remove the test manifold. 2C. DOUBLE WALL TANK WITH LIQUID-FILLED;(WET) INTERSTI ` nSAL SPACE PRIMARY (INTERNAL) TANK TEST NOTE: Keep the tank vertical (the reservoir on top) during the preinstallation testirig or the Squid (typically brine) may drain from the reservoir. 1. Open one service fitting and the fitting on the reservoir. Check for liquid in the reservoir - it should be about half full. Do not open the monitor fittings - liquid (typically brine) will be lost. Remove the remaining fittings, redope, and reinstall fitting plugs. 2. Visually check the interior of the tank for liquid - there should not be any. Install the test manifold in the open service fitting. Connect the pressure source to the test manifold. (See Figure 2-4). 3. Pressurize the primary (internal) tank to 5 PSIG. Add or remove air as necessary and allow the pressure to stabilize. Close the valve on the test manifold. Disconnect the air supply line. 4. Monitor the pressure for one hour. Soap ail fittings and nanways and watch for active air bubbles which indicate a leak Check the reservoir for bubbles in the monitor fluid. 5. Release the pressure from the primary tank. I i FROM COMPRESSOR PRESSURE RELIEF DEVICE AIR gJpPLY vALVE RESERVOIR FITTING AIR SUPPLY GAUGE SERVICE FITTING i I I 3 r r � i1\ CAUTION: Do not premrize the secandary tank (interstitial space) or the pnvary tank may rupture and cause tank failure. Chem the exterior of the tank for monitoring liquid - if liquid is found, wipe the tank dry and verify that the liquid does not reappear. Lift the tank to check the bottom. Do not roll the tank. /I\ DANGER: 0o not stand under the tank while it is being lifted. When the testis complete, remove the test manifold. Visually check the interior of the tank for liquid. Replace the protective covers in :he service fitting and the reservoir fitting.