Laserfiche WebLink
Field -installed piping and electrical fittings <br />Secondary pipe fittings can be field -installed using one of our optional two-piece <br />FRP couplings. <br />When used for piping connections, the FRP coupling is designed to provide <br />secondary containment connections only to the turbine enclosure. Do not use <br />the FRP coupling for primary piping connections to the turbine enclosure. <br />V TURBINE ENCLOSURE WALUINTERIOR <br />FEMALE MALE SECTION ADHESIVE <br />SECTION <br />0 <br />FRP Coupling Kit <br />(for 3" or 4" OD FRP pipe only) <br />22" MANWAY ON 6% 8'. & 10' DIAMETER TANKS ONLY <br />Flexible Entry Boot <br />FRP SLIP LUG <br />Tank Ladder <br />FRP Coupling Kit (3" or 4") <br />A two-piece field -installed 3" or 4" FRP coupling can be cemented in the <br />turbine enclosure to provide a watertight seal for piping penetrations in <br />high groundwater environments. <br />The FRP coupling is a two-piece fitting which is cemented to the <br />turbine enclosure. The FRP coupling's male and female sections <br />are threaded together to hold the fitting in place while the adhesive <br />cures. Each kit (Kit FC -3 or FC -4) includes the adhesive and <br />mixing instructions. <br />Flexible Entry Boot FEB <br />Flexible Entry Boots are rubber compression type boots installed into <br />the wall of the turbine enclosure to seal all pipe and conduit entries. <br />These boots are designed to permit up to a 300 angle of flexibility for <br />entries. This flexibility is important for aligning pipe connections or as a <br />stress relief for the pipe during backfilling and ground movement. The <br />Flexible Entry Boot is available for standard 3" and 4" secondary piping <br />and 3/4" conduit lines. <br />Tank Ladders <br />Our optional tank ladders are available in either carbon steel, <br />aluminum, or stainless steel. These ladders are shipped along with <br />the tank and field attached to the tank bottom with FRP mounting lugs. <br />Ladders are retained at the top with FRP slip lugs on the trunk of the <br />manway to allow for the vertical contraction and expansion of metal <br />ladders. (Manway and ladder are sold separately.) <br />Tank ladders are not recommended on 4' diameter tank capacities. <br />Because of limited space, the ladders interfere with tank entry. <br />Probe Drawstring <br />anks with a dry annular space, we provide a factory -installed "draw - <br />space monitoring fitting, to assist in positioning liquid sensors at <br />hilar space. <br />• <br />• <br />is <br />314° RUNG <br />(TYP.) <br />3/8" <br />F <br />12" TYP. <br />FRP <br />UNIVERI <br />t <br />MOUNTI <br />LUG <br />Flexible Entry Boot <br />FRP SLIP LUG <br />Tank Ladder <br />FRP Coupling Kit (3" or 4") <br />A two-piece field -installed 3" or 4" FRP coupling can be cemented in the <br />turbine enclosure to provide a watertight seal for piping penetrations in <br />high groundwater environments. <br />The FRP coupling is a two-piece fitting which is cemented to the <br />turbine enclosure. The FRP coupling's male and female sections <br />are threaded together to hold the fitting in place while the adhesive <br />cures. Each kit (Kit FC -3 or FC -4) includes the adhesive and <br />mixing instructions. <br />Flexible Entry Boot FEB <br />Flexible Entry Boots are rubber compression type boots installed into <br />the wall of the turbine enclosure to seal all pipe and conduit entries. <br />These boots are designed to permit up to a 300 angle of flexibility for <br />entries. This flexibility is important for aligning pipe connections or as a <br />stress relief for the pipe during backfilling and ground movement. The <br />Flexible Entry Boot is available for standard 3" and 4" secondary piping <br />and 3/4" conduit lines. <br />Tank Ladders <br />Our optional tank ladders are available in either carbon steel, <br />aluminum, or stainless steel. These ladders are shipped along with <br />the tank and field attached to the tank bottom with FRP mounting lugs. <br />Ladders are retained at the top with FRP slip lugs on the trunk of the <br />manway to allow for the vertical contraction and expansion of metal <br />ladders. (Manway and ladder are sold separately.) <br />Tank ladders are not recommended on 4' diameter tank capacities. <br />Because of limited space, the ladders interfere with tank entry. <br />Probe Drawstring <br />anks with a dry annular space, we provide a factory -installed "draw - <br />space monitoring fitting, to assist in positioning liquid sensors at <br />hilar space. <br />• <br />• <br />is <br />