Laserfiche WebLink
Feb 06 13 01.40p Elite IV Contactors 12094616342 p.3 <br />0 <br />H .w • <br />} R wr <br />, <br />Installation InsO:r <br />For repairing TCI FS or'i <br />VP <br />11M"Existing Direct Burial on Rigid or Flex:)! <br />This Kit applies to Traditional Repair products for Perp ?r <br />Fiberglass or Flex <br />g pipe installed "directly in the ground'. <br />WARNING: Prepare all surfaces to be bonded prior to coon, <br />Repair Kit for: , Failure to follow each step will void warranty & may result <br />URBKZ TCI SW FB 3950 -XX ..$ Before ordering the parts for this repair, determinE i- <br />pa9e 1 part and if you are in a "Flat" or "Curved" sump. See "`re <br />For Curved Sumo Repairs: Order the curved sump Borlji <br />Rev 3 - 4-23-2009 <br />General Instructions for: CLEANING: Spray all surfaces to be bonded with DBC Cleaner and allow t <br />cloth. Surfaces must be dry before applying bonder. <br />General Instructions for: BONDING TO POLY SUMPS OR <br />FIBERGLASS SUMPS: Clean, sand and rc u <br />apply RBB V between Bonding Ring & sump wall. <br />STEP 1: Loosen & Clean TO Nut <br />STEP 2: Verify Seal to Pipe <br />• Clean off any 'paste' or other bonders from around old TO <br />Inspect the boot <br />body & sump wall, <br />Patch & seal any possible leak paths <br />• Leave the clamp in place <br />between the pipe & the remaining <br />• Remove the plastic nut off the fitting <br />boot <br />• Clean & sand sump wall <br />Cut off the old plastic nut & discard <br />• Spray TCI Body & sanded sump wall with DBC cleaner <br />STEP 4: Install Bonding Ring, Nut, & Cuff Reducer <br />Wrack Bonding Ring over the existing pipe <br />Wrack Repair Nut over the existing pipe <br />Wrack Cuff Reducer over the existing pipe <br />STEP 5: Bond repair parts & Clamp <br />• Bond "Bonding Ring" with DBB III & clamp <br />Bond "Repair Nut" with DBB III & clamp <br />• Bond "Cuff Reducer" with DBB III & clamp <br />Seal around here <br />STEP 6: Install The Bonding Ring & Nut <br />• Apply DBB V to the sump side of the Br n4 <br />• Slide the Bonding Ring up to the Sump .Aa <br />• Apply DBB V to the sump side of the Nt t <br />• Thread Nut onto old TO body & tighte } <br />Apply DBB V to Sump side of <br />Bonding Ring <br />Apply DBB V to Sump <br />Replacement Nut <br />Bondin <br />am <br />i <br />4 P `y• <br />lotions <br />13 3950's with <br />ging applications" Repair Kit <br />I culjr piping entries on Existing <br />'acting installation steps below, <br />n premature failure of penetration fitting. <br />jou have a "Fine" or "Course" thread <br />l: Tips" if unsure which part(s) you have. <br />i; Rine In addition to this kit <br />•air dry or wipe excess with a clean dry <br />up sump surfaces. Clean fitting and <br />STEP 3: Clean all Repair Components <br />Clean all repair components with DBC <br />prior to installation <br />Split TO Cleaner <br />Nut <br />�w bo -3C' <br />`?7 <br />Split <br />Cuff Reducer Split Bonding Ring <br />n <br />rig Ring <br />I <br />to Bonding Ring <br />erment Nut threaded in place <br />Diversified Products Manufacturing Inc. 5523 Baggett Marysville Road, Oroville, CA 9! 9 530-534-3966 www.dpm-llc.com <br />