COMPLIANCE INFO_2015-2016 - Laserfiche WebLink

Home Browse Search

!,7U fl F P Y •® i t Bu[(ebn No. A1201 F Glass August 15, 2007 STAR • SMITH • FIBERCAST ENVIRONMENTAL HEATH nGPARTAAFNT SECTION 1 — Scope This section covers the use of fiberglass reinforced plastic (FRP) pipe for mild chemical and grater services up to 210'F and 450 prig steady pressure. The piping system shall be furnished and installed complete with all fittings. joining materials. supports, specials, and other necessary appurtenances. SECTION 2 — General Conditions 2.01 Coordination. Material furnished and work per- formed under this section shall be coordinated with related ,work and equipment specified under other sections. Valves Section Supports Section Equipment Section 2.02 Governing Standards. Except as modified or supplemented herein, all materials and construction methods shall comply with the applicable provisions of the following specifications and be tested using the following standards: Standard Specifications ASTM D2996 - Standard Specification for Filament - Wound "Fiberglass' (Glass -Fiber - Reinforced -Thermosetting Resin) Pipe ASTM D4024 - Standard Specification for Reinforced Thermosetting Resin (RTR) Flanges ASTM D5685 - Standard Specification for "Fiberglass" (G lass -Fiber -Reinforced -Thermosetting - Resin) Pressure Pipe Fittings Standard Test Methods ASTM D2992 - Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for "Fiberglass" (Glass -Fiber -Reinforced - Thermosetting Resin) Pipe and Fittings ASTM D2925 - Standard Practice for Measuring Beam Deflection of Reinforced Thermosetting Plastic Pipe Under Full Bore Flow ASTM D1599 - Standard Test Method for Short -Time Hydraulic Failure Pressure of Plastic Pipe, Tubing and Fittings ASTM D2105 - Standard Test Method for Longitudinal Tensile Properties of `Fiberglass" (Glass - Fiber -Reinforced -Thermosetting Resin) Pipe and Tube ASTM D2412 - Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel -Plate Loading 0 Trademark of Varco IIP, Inc - 0 2005, nc_02005, NATIONAL OILWELL VARCO RED THREADe II Piping System 10I: 0hi : 1 601.111 NN* 19[oi.,19W61 2.03 Operating Conditions. In addition to the above listed minimum design requirements, the system shall meet the following minimum operating conditions: a. Operating Pressure b. Operating Temperature c. Fluid Conveyed d. Test Pressure 2.04 Quality Assurance. Pipe manufacturer's quality program shall be in compliance with ISO 9001 and/or API 01. 2.05 Delivery. Storage. and Handling. Pipe and fit- tings shall be protected from damage due to impact and point loading. Pipe shall be properly supported to avoid damage due to flexural strains. The contractor shall not al- low dirt. debris, or other extraneous materials to get into pipe and fittings. All factory machined areas shall be protected from sunlight until installed. 2.06 Acceptable Manufacturers. FGS Smith Fibercast, 501-5684010, or approved equal. SECTION 3 — Materials and Construction 3.01 2"-24" Pipe. The pipe shall be manufactured by the filament winding process using an amine cured epoxy thermosetting resin to impregnate strands of continuous glass filaments, which are wound around a mandrel at a 54;6 winding angle under controlled tension. Pipe shall be heat cured and the cure shall be confirmed using a Differential Scanning Calorimeter. Pipe shall be supplied with a matching tapered bell and a matching tapered spigot. Pipe shall have a minimum continuous steady pressure rat- ing of 225 psig at 21WF in accordance with ASTM D2992 Procedure A. All pipe shall be 100% hydrotested at the factory before ship- ment at a minimum pressure of 300 prig. 3.02 Flanges and Fittings. All fittings shall be manu- factured using the same type materials as the pipe. Fittings may be manufactured either by compression molding or spray-up/contact molding methods.