COMPLIANCE INFO_1992-2000 - Laserfiche WebLink

Home Browse Search

�4=t I #I ("#�i ;" The OPW 233-E Extractor fitting is for use with any 11/211 foot valve with a maximum outside diameter of 23/4'. The 233-E has 4" male thread for con- nection to 4" tank flange and is gas- ket -sealed to prevent loss of prime, caused by air being sucked in through the top fitting. Materials Body: cadmium plated cast iron Cap and suction stub adaptor: bronze Gasket: chromed tanned leather SIZE: 1'/2" WT.: 20.22 lbs. 233-E-4040 The OPW 233-P Extractor fitting has internal threads to accept a co cting nipple between the extr he tank flange, whic ion to adjust the 3 -Pin relatio a cage of the 2 placed because it is t I - it is simply lifted out like a Materials Body: cast iron Cage: bronze Seals: buna-N 0 -ring SIZE: 2" WT.: 18.00 lbs. 233-P-6050 The OPW 233-V Series Extractors are used to hold and position the OPW 53-V Series Float Vent Valves in the underground storage tank. It is furnished complete with an extractable cage. The entire Float Vent sub -assembly can be extracted from the tank by using either an OPW 52 or 89 Extractor Wrench for tank testing. The OPW 233-V extractor is a single outlet extractor used in non-manifolded vapor recovery systems, or systems such as shown on p. 7. Materials: Body: cast iron w/Duragard® coating Extractor: bronze SIZE: 4" x 2" WT.: 15.33 lbs. 233-V-4420 The OPW 233 -VM extractor is a multi -outlet extractor, available in 2 sizes; used in direct manifolded systems, vapor recovery, or where provision for Stage II Vapor Recovery is needed. SIZES: 4" x 2" x 3" WT. 18.73lbs. 233 -VM -6045 4" x 2" x 2" WT. 16.62 lbs. 233 -VM -4422 All OPW 233-V series extractors are specially coated with black Duragard® coating, for improved corrosion resistance and easier cage removal. M OPW 233 Series OPW 233 Series Extractor fittings allow foot valves and ball float vent valves to be removed from under- ground tanks without breaking up the concrete. See pg. 12 for OPW extractor wrench selection. OPW 23 -E 11/2" Size Top threa 4" Outletthread 11/2' Inlet male thread 4" Inlet female thread 11/2" Maximum clear I.D. 2" through valve 27/8" OPW 233-P 2" Size Top thread 4" Outletthread 2" Inletthread 4" Cage thread 2" Maximum clear I.D. 2" through valve 31/2" 233 -VP Test Plugs OPW Test Plugs are used to isolate the tank from the vent piping system during tank testing. The 233 -VP plug is used on: 233-V-4420 (4" x 2") 233 -VM -4422 (4" x 2" x 2") The 233-VMP plug is used on: 233-V-4420 (4" x 2") 233 -VM -4422 (4" x 2" x 2") 233 -VM -6045 (4" x 2" x 3") 233 -VM -5522 (4" x 2" x 2") 233 -VP -6046 WT.: .78 lbs. 233-VMP-6047 WT.:1.24lbs. 0 Ni 233V 4420 (Tee) 233VM 4422 (Cross) 233VM 6045 (Cross) 233VM 5522 (Cross) Top Thread 4" 4" 4" 4" Outlet Thread 2" 2" 2" 2" _FF_3" 2„ Tank Connec- tion Thread Ext. 4" Ext. 4" Ext. 4" Int. 4" 0 Ni