COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

i SZ Environ FEB 8 Stud "Large Pipe" Repair Kit For Existing Flex or FRP Direct Burial Pipe from 2.7"to 3.6"OD repairs Page 2 i... a STEP 7:install&Bond Eccentric Insert& Step 8: Install The Eccentric insert&Multi-Sync Reducer Multi-Sync Reducer Back Together • Dry fit the Eccentric insert.Make sure it fits properly over the pipe& S J- • Wrack Eccentric Insert around the pipe inside the sleeve. • wrack Multi-Sync Reducer around the • Dry fit the Multi-Sync Reducer ' i pipe • Adjust the positions so that they lineup properly with the Repair i • Apply Zip-Tite to split area on Eccentric Sleeve&Pipe. _ Insert,press ends together&clamp Note: A proper fit will not cause extra pressure or force to the sleeve - • Apply Zip-rite to split area on Multi- and will allow a longer lasting repair. Sync Reducer,press ends together& Once you have the part lined up correctly clamp 1.Pull back the Mufti-Sync Reducer&Eccentric Insert _ 2.Apply Zip rite bonder all around the Eccentric Insert, _ '-_ 3.Slide Eccentric into the Repair sleeve in the proper position - __ 4.Apply Zip-rte bonder all around the Multi-Sync Reducer to it's pr : ��_ m - •. - . -- - S.Slide the Multi-sync Reducer in open place z-�:-•�••- �, -�, 6.Set the Clamp the around the sleeve&over the I• Eccentric Insert and tighten"snugly". 7.Set clamp over reducer end on the pipe&tighten enough to create a seal around the pipe. .. Parts are wracked around the pipe Nli,k[SltifRepat�titips}IJentsforlhet€piRdieuFar8cN3iELtr2endfcu1apiTreiBuda�appBcetioas_. _. •. _-_-. ._ i :-_:• •� - —'-""�--:.. fEnvirti�FEB EBsen� tratiii�`irt.irt. --- - 6dsT g Pipe ODF 11 DB Fill _- :, Inches Repair Kit Product Number clamp She oz. 1 - - 3"DW Vent Pie&3"DW GeoFlex-D 3.57 MSZ ENV FEB 8-3.6 60 42 - 3"FRP 3.5 MSZ ENV FEB 8-3.5 60 43 Parts are bonded&clamped3"SW Vent Pipe&3"SW GeoFlex-S 3.34 MSZ ENV FEB 8-3.4 60 43 Step 10: Fill With DBF II,Insert Fill Plug TOOLS REQUIRED; • Assemble DAG&DBF 11(see instructions on DPM website). _ Gloves and Static Mixer • Purge 1-2 oz. = 7/16"Nut driver (for flange nuts) • Fill fitting slowly. 5/16"Nut driver (for Band Clamps) Note: use Remote Fill option if access is limited -_- DAG Caulk Gun (for DBF It) • insert fill plug when filling is completed. ._ = DAGP Caulk Gun (Pneumatic version for DBF 11) • Clean any spilled DBF II with DBC and dispose DAG 111 Caulk Gun (for DBB V) of remaining products per local requirements- . ::. ,.. - PRODUCTS NEEDED: = DBC Cleaner Each DBF II&DBB v come Note: After 1 hour -_ zip rite Bonder with a Static Mixer the repair job may be DBF!I Polysulfide Liquid Fill hydro static tested - _- DBB V Bonder(for Poly or Fiberglass sumps) FILL Volume: tiler repair bootl - _ Volume of DBF II needed = See above chart Volume of Zip-Tlte needed = 3/4 Oz Remote Fill Option: Volume of DBB V needed = 24 ML The following parts are available to order if you can not properly position the assembled DBF II applicator gun to Parts in kit: "Fill"the repair. The Remote Fill parts provide a flexible Bonding Ring Studded UIZ Ms-6.7-4.4-2.0 extension for the filling process. Sleeve USz-6.7x6.7 RF Adapter 24"tube with male&female ends Eccentric Insert Ulz 6.7x5.0E RFA Tube-24 '/:"Tubing in 24"lengths Multi-Sync Reducer URZ MS 5.0-x.x(to match pipe size) 4 clamps 3#96,1#xx(see chart above) RFATube 32"Tubing in 200'length roll Fill Port Plug RFA xPlug RFA TubexTube %"Tube Coupling Repair Instructions RFA xFemale W Tube-Female Fill Port end RFA xMale Y2"Tube-Male Fill Port end RFA xPiug %z"Tube-Male Plug for fill port Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 50 of 70 i i I