COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

i i MSZ Environ FEB 8 Stud "Small Pipe" Repair Kit For Existing Flex or FRP Direct Burial Pipe from 1.8"to 2.7" OD repairs ` Page 2 STEP 7:Install&Bond Eccentric Insert&Multi- Step 8: Install The Eccentric Insert&Muni-Sync Reducer Sync Reducer Back Together • Dry fit the Eccentric insert.Make sure it fits properly over • Wrack Eccentric Insert around the pipe the pipe&inside the sleeve. • Wrack Multi-Sync Reducer around the pipe • Dry fit the Multi-Sync Reducer _"- • Apply Zip Trte to split area on Eccentric Insert, • Adjust the positions so that they lineup properly with the Repair Sleeve&Pipe. press ends together&damp 1 Note:A proper fit will not cause extra pressure or force to • ApplyZlp-Titeto split area on Multi-Sync ---- - - ' _ sleeve and Reducer,press ends together&damp the will allow a loner lasting repair. ' • Once you have the part lined up correctly _ 1. Pull back the Multi-Sync Reducer&Eccentric Insert 2.Apply Zip-Ttte bonder all around the Eccentric Insert;. e j 3.Slide Eccentric into the Repair sleeve in the proper position - 4.Apply Zip-Tte bonder all around the Multi-Sync Reducer w 5.Slide the Multi-Sync Reducer into it's proper place 6.Setthe Clamp the around the sleeve&over the Eccentric Insert and tighten"snugly". _ 7.Set clamp over reducer end on the pipe&tighten enough to create a seal around the pipe. Parts are wracked around the pipe 141k1yP4 Repair CRrrfjiiitients for I lE$fti7ttlt r€rngllli NanC :LrdCtut �s In l7ireet Bud�difg1 talions;-_—. - .�._..ekiSt. � .viron<EEB EB'. .ies'"erte-tr�tibf�fltrirt s Pipe 00, D8F II Fill j :A �' S ikinsU tM}ues Re it tot Product Num6arClam Size oz i 2"LOC 2.7 MSZ ENV FEB 8-2.7 44 37 2"DW Vern&2"DW GeoFtex-D 2.5 M52 ENV FEB 8-2.5 ao 38 :�'.. ._... :. 2"FRP 2.315 MSZ ENV FEB 8-2.4 40 39 ••-- 2"SW Vent&2"SW GeoFlex-5 2.3 MSZ ENV FEB 8-2.3 36 40 11/2"DW GeoFlex-D 2 MSZ ENV FEB 8-2.0 32 41 11/2"Steel 1.9 MSZ ENV FEB 8-1.9 32 42 Parts are bonded&clamped 11/2"SW GeoFlex-S 1.8 MSZ ENV FEB 8-1.8 28 42 Step 9: Fill With DBF It,Insert Fill Plug TOOLS REQUIRED: • Assemble DAG&DBF 11(see instructions on DPM website). Gloves and Static Mixer • Purge 1-2 oz. 7/16"Nut driver (for flange nuts) • Fill fitting slowly. - - _ 5/16"Nut driver (for Band Clamps) Note: Use Remote Fill option if access is limited " = DAG Caulk Gun (for DBF 11) 1 • Insert fill plug when filling is completed. = DAGP Caulk Gun (Pneumatic version for DBF 11) • Clean any spilled DBF 11 with DBC and dispose DAG III Caulk Gun (for DBB V) of remaining products per local requirements. PRODUCTS NEEDED: Each DBF 11&DBB V come Note: after 1 hour DBC Cleaner with a Static Mixer the repair job may,be Zip-Tfte Bonder hydro-static tested DBF Ii Polysulfide Liquid Fill •_. =_; DBB V Bonder(for Poly or Fiberglass sumps) ' FILL Volume: (Der repair boot) i Volume of DBF Il needed = See chart above Remote Fill Option: Volume of Zip-Ttte needed = 3/4 Oz i The following parts are available to order if you can not Volume of DBB V needed = 24 ML I properly position the assembled DBF 11 applicator gun to "fil("the repair. The Remote Fill parts provide a flexible Parts i : extension for the filling process. Bonding Ring Studded UIZ MS 6.0x4.4-2.0 i RF Adapter 24"tube with male&female ends Sleeve USZ-6.0x6.0 Eccentric Insert UiZ 6.Ox4.5E RFA Tube-24 h"Tubing in 24"lengths Multi-Sync Reducer URZ MS 4.5-x.x(to match pipe size) RFA Tube %h"Tubing in 200'length roll 5 clamps 3#96,1#72,1#xx(See chart above) RFA TubexTube %"Tube Coupling Fill Port Plug RFA xPlug RFA xFemale W Tube-Female Fill Port end Repair Instructions RFA xMale W Tube-Male Fill Port end RFA xPlug %"Tube-Male Plug for fill port Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 52 of 70