COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

Multi-Sync Repair Instructions For Environ FEB 3075A Repair Kit This Kit provides the Multi-Sync Repair parts for YV'Rigid Steel conduits In applications .100, h where the conduit pipe is coming thru the sump wall either straight or at excessive angles. For PVC coated conduits and conduits smaller than W,consult the factory. MSZ ENV FEB$075A WARNING.Prepare all surfaces to be bonded prior to completing installation steps below. For Environ Conduit Repairs Failure to follow each step will void warranty&may result in premature failure of penetration fitting. Page 1 This Kit Ippiles to rgoaftling: Environ FEB 3075 Darts Rev 2- 6-22-2009 With Y4"Rigid conduit PIRIng 1 i General Instructions for: CLEANING:Spray all surfaces to be bonded with DBC Cleaner and allow to air dry or wipe excess with a clean dry cloth. Surfaces must be dry before applying bonder. General Instructions for: BONDING TO POLY SUMPS OR FIBERGLASS SUMPS: Clean,sand and rough up sump surfaces. Clean fitting and apply DBBV between Bonding Ring&sump wall. STEP 1: Loosen&Clean Mounting Plate STEP 2: Clean all Repair Components STEP 3: Place&Dry Fit Bonding Ring&Sleeve • Remove clamp on the reducer at the pipe Clean all repair components with DBC Note: Make sure Bonding Ring Is placed over the studs • Remove the nuts from the mounting plate prior to Installation between the sump wall&the mounting plate,With 'Sealing Groves'positioned toward the sump wall and Pullback the mounting plate Cleaner the split part of the bonding ring toward the top • Split Split Clean off any'paste'or other bonders Place the split bonding ring over the studs,between from around old Environ body&sump Bonding Sleeve., the sump wall&the metal plate with the sealing Ring.. wall, grooves toward the sump wall. • Seal up any cracks or rips in rubber boot Snug up the metal plate with a couple of flange nuts • Clean&sand sump wall Place the split sleeve over the pipe&MA19_the • Spray Environ body&sanded sump wall bonding ring with the fill port up with DBC cleaner If everything fits properly,then loosen the nuts&pull 0 back the mounting plate again.to bond the parts together, Eccentric Insert Multi-Sync Reducer pzK You must$;.I any open space between the pipe &old boot area STEPS., Install Bonding Ring&Mounting Plate STEP 6: Install The Sleeve CA z e of the Bonding Seal around old boot&pipe,if needed Apply DBB V to the sump side Ring and slide it over the studs&up to the Slide In the sleeve with the fill port at the top. sump wall DO NOT push the sleeve over the snap ring Slide In the mounting plate Once you have the sleeve lined up correctly, Reinstall the flange nuts.Tighten snugly 1.Pullback the sleeve a little Reinstall the pipe clamp on the old boot 2.Apply a bead of DBB III all around the outer Note: Do not Over-tighten. Snug Is ok. edges of the bonding ring - Wipe any excess DBB V off the bonding ring 3.Slide sleeve over bonding ring&snap In place - Spray OBC onto cloth&wipe clean the outer (fill port at top) edges of The bonding ring. 4.Set the Clamp the around the sleeve&over STEP 4: Bond Sleeve&Bonding Ring r the bonding t!ring and hteri!snugly'.t. • Apply DBB III to split bonding ring. Use 1 of the clamps to hold In place while curing. • Apply DB8 III tothe split sleeve and use 2 clamps to hold in place while curing. • Leave these clamps in place for approx 30 minutes for curing before proceeding to DBRV goes on'grooved" the next step side toward sump Fill port on top Bonding Ring in place. Sleeve in place with clamp Old clamp in place REEM Wipe any excess DBS V from outer edge Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 55 of 70