COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

i S ENV FEB 3100 Series For Environ Series 3100 Conduit repairs Page 2 step 8: Install The Eccentric Insert&Multi-Sync Reducer STEP 7:install&Bond Eccentric Insert&Multi- Dry fit the Eccentric insert.Make sure it fits properly mark the Sync Reducer Back Together over the pipe&inside the sleeve. alignment j.... Wrack Eccentric insert around the pipe Dry fit the Mufti-Sync Reducer • Wrack Multi Sync Reducer around the pipe Adjust the positions so that they lineup property with • Apply DOB 111 to split area on Eccentric Insert, the Repair Sleeve&Pipe. press ends together&clamp Note:A proper fit will not cause extra pressure or force to. • Apply DBB IiI to split area on Multi-Sync the sleeve and will allow a longer lasting repair. Reducer,press ends together&clamp • Once you have the part lined up correctly —'�•_'�" - " - _ ' 1. Pull back the Multi-Sync Reducer&Eccentric Insert 2.Apply DBB Ili bonder all around the Eccentric Insert, i 3.Slide Eccentric into the Repair sleeve in the proper - -- - position i — 4.Apply DBB IIi bonder all around the Multi-Sync { Reducer 5.Slide the Multi-Sync Reducer into it's proper place _= 6.Set the Clamp the around the sleeve&over the - Eccentric Insert and tighten"snugly". i 7.Set clamp over reducer end on the pipe&tighten 1 Parts are wracked around the pipe enough to create a seal around the pipe. =Molt)Sync Rehr omPonents fol Per Conidatl eicationswithpxistis� hulina_FEB. EBseries iietrationfittin'9 _..-77 T_ _ �- teyRfgF�ok[#�OltSt?RSr Pipe pD damp DBF 11 3 � rn is:8i 1t�ka "`s4is7et%oii Inches Repair Kit Product Number Size Hit oz. I FEB-3150for 1 DW GeoFlex-D Pie 1.45 Mi ENV FEB 3150 24 12 FEB-3100 for 1"Ri id Condi 1.315 MSZ ENV FEB 3157 20 12 3 _ --- FEB-3075 for 3/4"GeoFlex D P 1.18 Consult Facto 20 13 Pi FEB-3075 for 3/4'RI id Conduit 1.05 MSZ ENV FEB 3157 16 14 Parts are bonded&clamped FEB 3050 for 1 2'Rigid Conduit 0.84 1l ENV FEB 3050 16 1 14 Step 10: Fill With DBF 11,Insert Fill Plug TOOLS REQUIRED: • Assemble DAG&DBF 11(see Instructions on DPM website). Gloves and Static Mixer • Purge a maximum of 2 oz. = 5/16"Nut driver (for Band Clamps) • Fill fitting slowly. DAG Caulk Gun (for DBF 11) I • Insert fill plug when filling is completed. DAGP Caulk Gun (Pneumatic version for DBF II) i • Clean any spilled DBF tl with DBC and dispose DAG III Caulk Gun (for DBB V) of remaining products per local requirements..,, PROAUCT5 CEDED: DBC Cleaner Each DBF II&DBB V come Note: After 1 hour DBB Ill Bonder with a Static Mixer the repair job may be -- — DBF 11 Polysulfide Liquid Fill hydro-static tested DBB V Bonder(for Poly or Fiberglass sumps) FILL Volume: {per repair boot) { Volume of DBF Il needed = See Chart Above j Volume of DBB Ill needed = 1/2 Oz Volume of DBB V needed = 13 ML Remote Fill Option: The following parts are available to order if you can not Parts In kit: properly position the assembled DBF II applicator gun to Bonding Ring UIZ-MS-4.5x2.5-2.3 "fill"the repair. The Remote Fill parts provide a flexible sleeve USZ-4.5x4.5 Eccentric Insert U!Z-4.5x3.6E extension for the filling process. Multi-sync Reducer URZ-3.6x XX(To match the pipe size) RF Adapter 24"tube with male&female ends 5 clamps 3#72,1#60,1#xx(see chart above) RFA Tube-24 A"Tubing in 24"lengths Fill Port Plug RFAxPiug RFATube Y:"Tubing in 200'length roll Repair Instructions RFA TubexTube Ya"Tube Coupling RFA xFemale %"Tube-Female Fill Port end RFA xMale Y"Tube-Male Fill Port end j RFA xPlug "Tube-Male Plug for fill port Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 54 of 70 i I i i