COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

Multi-Sync Repair Instructions For Environ CEB 3075 Repair Kit V This Kit provides the Multi-Sync Repair parts fora"Rigid Steel conduits In applications iflim-ir where the conduit pipe is coming thru the sump wall either straight or at excessive angles. For PVC coated conduits and conduits smaller than Y4",consult the factory. MSZ ENV CEB 3076 WARNING:Prepare all surfaces to be bonded prior to completing Installation steps below. For Environ Conduit Repairs Failure to follow each step will void warranty&may result in premature failure of penetration fitting. Page 1 This Kit avalies to repairing: Environ CEEB 3075 part Rev 2- 6-23-2009 With Ea"Rigid conduit piping General instructions for: CLEANING:Spray all surfaces to be bonded with DBC Cleaner and allow to air dry or wipe excess with a clean dry cloth. Sur-faces must be dry before applying bonder. General Instructions for. BONDING TO POLY SUMPS OR FIBERGLASS SUMPS: Clean,sand and rough up sump surfaces. clean fitting and apply pjB_V between Bonding Ring&sump wall. STEP 1: Loosen&Clean Mounting Plate STEP 2: Clean all Repair Components STEP 3: Place 8,Dry Fit Bonding Ring&Sleeve • Remove clamp on the reducer at the pipe Clean all repair components with OBC Note: Make sure Bonding Fang is placed over the studs • Remove the nuts from the mounting plate prior to Installation between the sump wall&the mounting plate,with "Sealing Groves"positioned toward the sump wall and • Pull back the mounting plate split Cleaner Split the split part of the bonding ring toward the top • Clean off any'paste'or other bonders BondingSleeve Place the split bonding ring over the studs,between from around old Environ body&sump Ring the sump wall&the metal plate with the sealing wall, grooves toward the sump wall. • Seal up any cracks or rips in rubber boot Snug up the metal plate with a couple of flange nuts • Clean&sand sump wall Place the split sleeve over the pipe&unto the • Spray Environ body&sanded sump wall bonding ring with the fill port up with DBC cleaner if everything fits properly,then loosen the nuts&pull • back the mounting plate again to bond the parts Eccentric Insert Multi-Sync Reducer AL. L-You must seal any open space between the pipe &old boot area STEP S Install Bonding Ring&Mounting Plate STEP 6- Install The Sleeve It - Seal around old boot&pipe,if needed w ....... Apply DBB V to the sump side of the Bonding Ring and slide it over the studs&up to the - Slide In the sleeve with the fill port at the top. sump wall DO NOT push the sleeve over the snap ring Slide in the mounting plate Once you have the sleeve lined up correctly, • Reinstall the flange nuts.Tighten snugly 1.Pull back the sleeve a little Reinstall the pipe clamp on the old boot 2.Apply a bead of DBB III all around the outer Note: Do not Over-tighten. Snug is okedges of the bonding ring • Wipe any excess DBB V off the bonding ring 3.Slide sleeve over bonding ring&snap in place Spray DBC onto cloth&wipe clean the outer (fill port at top) edges f the bonding ring. 4.Set the Clamp the around the sleeve&over STEP 4: Bond Sleeve&Bonding Ring the bonding ring and,tighten",snugly'. • Apply DBB III to split bonding ring. Use 1 of the clamps to hold in place while curing. • Apply DBB,III to the split sleeve and use 2 clamps to hold In place while curing. • Leave these clamps In place for approx 30 minutes for curing before Proceeding to the next step D613 Vgoi§on"grooved" DBB III.here side toward sump Fill port on top Sleeve In place with clamp Bonding Ring in place. Wipe any excess DBB V from outer edge Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 57 of 70