Laserfiche WebLink
3 <br /> a <br /> i <br /> l.. <br /> MS ENV CES 3075 , <br /> For Environ Sub-Miniature Series Conduit repairs <br /> Page 2 <br /> f <br /> STEP 7:Install&Bond Eccentric Insert&Multi- Step B: Install The Eccentric Insert&Multi-Sync Reducer <br /> Sync Reducer Back Together Ory fit the Eccentric insert.Make sure it fits properly over the pipe&inside the sleeve. i.. <br /> • Wrack Eccentric Insert around the pipe Dry fit the Mufti-Sync Reducer <br /> • Wrack Multi-Sync Reducer around the pipe Adjust the positions so that they lineup properly with the Repair Sleeve&Pipe. <br /> • Apply DBB III to split area on Eccentric insert, Note:A proper fit will not cause extra pressure or force to the sleeve and will allow a longer i <br /> press ends together&clamp lasting repair. i <br /> • Apply DBB III to split area on Multi-Sync Once you have the part lined up correctly <br /> Reducer,press ends together&clamp 1. Pull back the Multi-Sync Reducer&Eccentric insert <br /> 2.Apply DBB III bonder all around the Eccentric insert, <br /> 3.Slide Eccentric-into the Repair sleeve in the proper position <br /> 4,Apply DBB III bonder all around the Multi-Sync Reducer <br /> 5.Slide the Mufti-Sync Reducer into it's proper place <br /> 6.Set the Clamp the around the sleeve&over the Eccentric Insert and tighten"snugly". <br /> -= z 7.Set clamp over reducer end on the pipe&tighten enough to create a seal around the <br /> - - s <br /> pipe. <br /> Parts are wracked around the pipeElm., <br /> 1 <br /> • °, ( ;irk � k i 1. € <br /> Parts are bonded&clamped ± <br /> I <br /> Step 10: Fill With DBF ii,Insert Fill Plug TOOLS REQUIRED: <br /> • Assemble DAG&DBF 11(see instructions on DPM website). Gloves and Static Mixer <br /> • Purge a maximum of 2 oz. _ _- _ 5/16"Nut driver (for Band Clamps) <br /> Fill fitting slowly. - DAG Caulk Gun (for DBF 11) } <br /> • insert fill plug when filling is completed. DAGP Caulk Gun (Pneumatic version for DBF 11} <br /> • Clean any spilled DBF 11 with DBC and dispose DAG ill Caulk Gun (for DBB V) <br /> of remaining products per local requirements. <br /> PBODUgS N E�1 I <br /> _ DBC Cleaner Each DBF 11&DBB V come <br /> Note: After 1 hour = DBB III Bonder with a Static Mixer <br /> the repair job may be __:__ - DBF 11 Polysulfide Liquid FII€ <br /> hydro-static tested - - DBB V Bonder(for Poly or Fiberglass sumps) <br /> :_... FiLL Volume: (cer reoair boot! <br /> Volume of DBF II needed = 13 Oz <br /> Volume of DBB 111 needed = 1/2 Oz <br /> Volume of DBB V needed = 9 ML <br /> Remote Fill Option: <br /> The following parts are available to order if you can not Parts in kit: <br /> properly position the assembled DBF 11 applicator gun to Bonding Ring UIZ-MS-3.5x1.8-1.58 <br /> "fill"the repair. The Remote Fill parts provide a flexible Sleeve uSZ-3.5x3.5 <br /> Eccentric Insert UIZ-3.5x2.6E <br /> extension for the filling process. Multi-sync Reducer URZ-2.6x1.1 j <br /> RF Adapter 24"tube with male&female ends 5 clamps 3#60,1#40,1#16 <br /> RFATube-24 �"Tubing in 24"lengths Fill Port Plug RFAxPlug <br /> RFATube 'r4"Tubing in 200'length roll Repair Instructions <br /> RFA TubexTube %"Tube Coupling <br /> RFA xFemale %"Tube-Female Fill Port end <br /> RFA xMale W Tube-Male Fill Port end <br /> RFA xPlug '/:"Tube-Male Plug for fill port <br /> Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 58 of 70 <br /> i <br />