COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

i Z Environ FEB 8 Stud "Small Pipe" Repair Kit - For Existing Flex or FRP Direct Burial Pipe from 9.8"to 2.7" OD repairs Page 2 Step 8: Install The Eccentric insert&Multi-Sync Reducer STEP 7:instal!&Bond Eccentric Insert&Multi- ;! • Dry fit the Eccentric insert.Make sure it fits properly over Sync Reducer Back Together the pipe&inside the sleeve. . • Wrack Eccentric Insert around the pipe Dry fit the Multi-Sync Reducer _- • Wrack Multi-Sync Reducer around the pipe , Adjust the positions so that they lineup properly with the = --- _. • Apply Zip-rite to split area on Eccentric insert, -- Repair Sleeve&Pipe. ... press ends together&damp Note:A proper fit will not cause extra pressure or force to • Apply Zip-rite to split area on Multi-Sync the sleeve and wilt allow a longer lasting repair. Lmm� �A Reducer,press ends together&clamp Once you have the part lined up correctly 1 1.Pull back the Multi-Sync Reducer&Eccentric Insert 2.Apply Zip-Tate bonder all around the Eccentric Insert;; 3.Slide Eccentric into the Repair sleeve in the proper position 4.Apply Zip-rite bonder all around the Multi-Sync _ Reducer 5.Slide the Mufti-Sync Reducer into it's proper place 6.Set the Clamp the around the sleeve&over the Eccentric Insert and tighten"snugly". 7.Set clamp over reducer end on the pipe&tighten enough to create a seal around the pipe. _...... Parts are wracked around the pipe - -� � ._ n erttr e3i ettaciEiPajYpc,ii4„is::�•m. witjl;;: j�lulti-�ncRePa-fr�ariYjiPnei�trfclt pendittii@�l�on;t'��..�.icaLaS2r 8._:I�i� ,� _ -. ,, i%:tistiri i:i'i47 ilri Fiit3 DE�se'r es iii t �tttn _.:. _ _,. ..�_. -•• I DBF It Fill 1 -_ -- — - _ inches Re air Kit Product Number Clam Size oz = 44 37 2"LCX 2.7 M52 ENV FEB - 2"DW Vent&2"DW GeoFtex-D 2.5 MSZ ENV FEB 8 2.5 40 38 } = 2.315 MSZ ENV FEB 8-2.4 40 39 -_ - 2"FRP 36 2"SW Vent&2"SW Geo Flex-S 2.3 MSZ ENV FEB 8-2.3 1 "DW GeoFlex-D 2 MSZ 32 41 ENV FEB 8 2.0 i 11 "Steel 1.9 MSZ ENV FEB 8.1.9 32 42 Parts are bonded&clamped I 1 "SW GeoFlex-S 1.8 MSZ ENV FEB 8-1.8 28 42 T001S REQUIRED: Step 9: Fill With DBF 11,Insert Fill Plug Gloves and Static Mixer • Assemble DAG&DBF it(see instructions on DPM website). 7/16"Nut driver (for flange nuts) • Purge i-2 oz. for Ban • Fill fitting slowly. 5/16"Nut driver ( d Clamps) Note: Use Remote Fitt option if access is limited DAG Caulk Gun (for DBF Il) • Insert fill plug when filling Is completed. DAGP Caulk Gun (Pneumatic version for DBF II • Clean any spilled DBF 11 with DBC and dispose DAG III Caulk Gun (for DEB V) of remaining products per local requirements. PRODUCTS NEEDED: Each DBF 11&DBB V come _- DBC Cleaner with a Static Mixer Note: After 2 hour _ Zip-Tate Bonder the repair job may be = DBF ll polysulfide Liquid Fill hydro-static tested -> -- = DBB V Bonder(for Poly or Fiberglass sumps) FILL Volume fuer reaair boat) Volume of DBF ll needed = See chart above Remote Fill Option: Volume of Zip-Tite needed = 3/402 The following parts are available to order if you can not Volume of DBB V needed = 24 ML properly position the assembled DBF Il applicator gun to Parts in kit• "fill"the repair. The Remote Fill parts provide a flexible Banding Ring Studded UIZ MS 6.0x4.4-2.0 extension for the filling process. Sleeve USZ-6.0x6.0 RF Adapter 24"tube with male&female ends Eccentric insert UIZ 6.ox4.5E RFA Tube-24 % Tubing in 24"lengths Multi-Sync Reducer URZ MS 4.5-x.x(to match pipe size) RFA Tube W'Tubing in 200'length roll 5 clamps 3#96,1#72,1#xx(See chart above) RFA TubexTube W Tube Coupling Fill Port Plug RFA xPlug RFAxFemale %z'Tube-Female Fill Port end Repair Instructions RFA xMaie %"Tube-Male Fill Port end RFA xPlug %"Tube-Male Plug for fill port Diversified Products Manufacturing Inc. 5523 Baggett Marysville Road,Oroviile,CA 95965 530-534-3966 www.dpm-Ilc.com