COMPLIANCE INFO_2009-2012 - Laserfiche WebLink

Home Browse Search

I i f Multi-Sync Repair Instructions0DP ! For Environ Direct Burial Series "8 Stud" Repair Kit i This wM) fq:, kit provides the Multi-Sync Repair parts for existing Flex or FRP Pipe from 1.8'°up to V.„ ; 2.7'OD in Direct Burial applications where the pipe is coming thru the sump wall either r straight or at excessive angles. MSZ ENV FES 8-XX WARNING:Prepare all surfaces to be bonded prior to completing installation steps below. For Environ repairs with Failure to follow each step will void warranty&may result in premature failure of penetration fitting. Direct Burial Small Pipe This Kit applies f r repairing:Environ FEB 6000 Series parts i Page 1 With piping from 1&up to 2.7" OD Rev 3 6-26-2009 General Instructions for: CLEANING:Spray all surfaces to be bonded with DBC Cleaner and allow to air dry or wipe excess with a clean dry s cloth. Surfaces must be dry before applying bonder. General Instructions for: BONDING TO POLY SUMPS OR FIBERGLASS SUMPS: Clean,sand and rough up sump surfaces. Clean fitting and 1 apply DBL V between Bonding Ring&sump wall. On Poly Sumps if sump wall is un-even use DRP in place of DBB V. STEP 2: Clean all Repair Components STEP 3: Place&Dry Fit Bonding Ring&Sleeve STEP 1: loosen Nuts&pull Back Metal Ring Clean all repair components with DBC Note: Make sure Bonding Ring Is placed with the"Seating • Remove Nuts Groves"positioned toward the sump wail • Pull back metal mounting flange prior to installation Place the split bonding ring over the pipe with the • Clean off any'paste'or other bonders Split Bonding Cleaner Split sealing grooves toward the sump wall `. from around the Environ body&sumpRing Sleeve Place the bonding ring over the studs wall, Push metal mounting flange over the studs • Clean&sand sump wall r Place the split sleeve over the pipe&up to the bonding • Spray Environ Body&sanded sump wall ring with the fill port up with DBC cleaner �= j f� • If needed patch old boot to seal back wall _ °:i t Eccentric Insert Multi-Sync Reducer - educe t •�,5-c1 t u x Ar,* ti 0 ` STEPS: Install the Bonding Ring STEP 6: install The Sleeve _ 1r1 (f1f@" ;: Apply DBB V to the sump side o#the Bonding Seal around the existing boot &pipe if needed. _*._=-• I port at the Cilsti # _ Ring and slide it over the studs&up to the OncPose you have the sleevon the sleeve with e lined up correctly,p -.- sump wall Slide on the metal mounting flange 1.Apply a bead of Zip-Tate all around the outer - Thread on the flange nuts. edges of the bonding ring Cuff Note:Tighten the flange nuts"snugly". 2.Slide sleeve over bonding ring Cuff&snap in Do not Ower-tighten. Snug is ok. place(fill port at top) _ Wipe any excess DBB V off the bonding ring 3.Set the Clamp,#96,the around the sleeve& • Spray DBC onto cloth&wipe clean the outer over the bonding ring and tighten"snugly". edges of the bonding ring. STEP 4: Bond Sleeve&Bonding Ring DBB V goes on _- • Apply Zip-Tite to the split bonding ring. "grooved"side - Use 1 clamp,#96,to hold in place while °� ..... toward sump _= • curing. e - • Apply Zip-Tite to the split sleeve and use 2 .a clamps,#96,to hold in place while - p-Tite here curing. - _ • Leave these clamps in place for approx 30 a ~ minutes for curing before proceeding to the next step - You must seal any open spaces between the pipe &the old Environ boot - - - -- Fill port on top v. - Sleeve 4ce over"Cuff'with clamp o _ Bonding Ring in place. ° Wipe any excess DBB V from outer edge Diversified Products Manufacturing Inc. 5523 Baggett Marysville Road,Orovilie,CA 95965 530-534dpm-llc.com 3966 www.