Laserfiche WebLink
r <br />q ' <br />Termination Fittings D. Bonding and Assembly_ <br />Termination at the bulk tank connections is accom- (For Containment Piping) <br />plishedbyusingaterrninatiortconcentric red <br />ucerwith Use only DS -7014, DS -7024 or DS -7069 adhesitr <br />N: female NPT threaded outlet. (See Figure S e<= <br />( .., J manufactured by A.0: Smith -Inland for installation of `- <br />tx' <br />A.O. Smith -Inland rontaainment piping' systems. Th <br />Fiber Glass - <br />Threaded Adepten number of 3" containment fittings which can. b <br />(Sell x Male) bonded from one DS -7014, DS -7024, or DS -7 - <br />adhesive kit is shown in Table II. <br />TABLE !1• <br />Bonding of Containment'Fitiings <br />F - <br />M DS 7014 b OS 7024 Kits DS -7069 -Kt <br />t k.. 4 <br />e Type of Fitting Fittings Per Kit Fittings PQ ,at.tt <br />O <br />0 O 3% NPT 3.. 90o Elbow 1112 <br />3" 45 Elbow 2 3 <br />3" Tee l.=s <br />f o O 2 <br />,Cpgo ` 3 <br />3 x;2• <br />Termination � <br />Tank Concentric Reducer 2 <br />figure 6 3, <br />i <br />NOTE: Information for 4" and 6•' diameter' fatUngs not •`_ <br />available at present time.' x <br />Termination at the dispenser is at the end of the fiber <br />a glass containment piping and is accomplished using a <br />Refer to bonding procedures in Manual�"5#tom �, <br />g '^termination concentric reducer. (See Figure 6) adhesive mixing and surface clean' , <br />After cleaning all sanded surfaces ap I axt <br />ril� Oiapenser� <br />N11�lmpact Valve x <br />�= coating (i/16" minimum) of adhesive, t <br />w.,- (bell) ares of the fitting. The stir stick s i <br />Faber Glass the adhesive kit works.wel l as an <br />Threaded Adapter coat the tabs (flat bonding ,urfa�e�) <br />;ee11 z Male) the fittings with adhesive (1 /16' r5s�n m ttthtC , <br />hick c <br />Apply coating 16 min <br />p } <br />r O O the sanded surfaces of the pipe en s f` <br />Y <br />NOTE: Two-piece containment'Al <br />s more adhesive than <br />r O p -- _ Smith -Inland bell and sp a <br />o <br />Use the bolts, nuts and ' r <br />g pipe. Two 7r- 6 <br />Galvanized Steel fittings on the � <br />Figure 6 for the bolts. Note that a flat was <br />e halves of the fittings.; (See Fa%1ur ar <br />and bolts completely. <br />Termination on the shear valve ( impact valve) may be , <br />accomplished with a flexible hose, clamped and Make sure that adhesive fills an � <br />Y.,gaps ki Weeri pe <br />c bonded in place. (NOTE Not supplied by AO. Smith- <br />- and fitting sockets t -1 -- <br />Inland.) (See Figure 7) <br />Dispenser Cashould be taken not 't=� di4fl1rb thf-c6, <br />�-- impact Valve piping joint when assernblidWa�dditio t a he <br />918 gas <br />adhesive must be fully cured befo)"e�p� n� , <br />assembled joint. Use adhestvd�a t,r <br />NPT threads on termination fitting; " <br />RubberMoot <br />' igwe 7 Galvenned Steel <br />