Laserfiche WebLink
14. INTERSTITIAL SPACE MONITORING <br />A. Visual monitoring [Section 2632 (c) (1)l <br />(a) Exterior surface and floor beneath tank monitored by direct viewing <br />(b) Daily visual inspections <br />_ (c) Liquid level in tank to be recorded at time of inspection <br />_ (d) If liquid observed around or beneath primary tank, owner will determine if an unauthorized release <br />has occurred. <br />B. Mechanical or electronic monitoring [Section 2632 (c) (2)) <br />(a) Continuous monitoring system connected to an audible and visual alarm system. <br />Monitoring equipment to be installed <br />Manufacturer- <br />Model Number:_ <br />Sensor Type: VaporLiquid Both. <br />ogMk <br />Sensor/Panel specifications. <br />Location(s) for sensors: <br />Tank: Piping' <br />Dispenser' <br />C. Monitoring and response plan submitted [Section 2632 (d) (1) & (2)]. <br />15. Any special accessories, fittings, coatings, or linings not inherent within the initial design of the 10 tank or <br />double-wall UST. [Section 2631 (b)] <br />A. Approved by a nationally recognized independent testing organization. <br />B. Demonstration of integrity with the primary and/or. secondary containment. <br />2 <br />D Alternate construction <br />. . <br />9 n for new underground storage tanks conta ing motor vehicles fuel [Section 26331. <br />(1) <br />Monitoring and response plan [Section 26341. <br />(2) <br />Underground storage tank composed of.... <br />(a) Fiberglass reinforced plastic. <br />(b) Cathodically protected steel. <br />(c) Steel clad with fiberglass reinforced plastic. <br />(d) Other material that complies with section 2631 and 2632. <br />(3) <br />Floor of leak interception and detection system constructed on a firm base and sloped to a <br />_ <br />collection sump (use of membrane liners comply with section 2631 (d) (6) requirements.) <br />(4) <br />Access casings installed in the collection sump of the secondary containment system with <br />the following: <br />backfill in the interstitial space. The access casing shall meet all of <br />Designed and installed to allow the liquid to flow into the casing. <br />Sized to allow removal of collected liquid and able to withstand all anticipated applied <br />stresses. <br />Constructed of material that will not be structurally weakened. <br />Screened along entire vertical zone of permeable material. <br />Capable of preventing leakage of any hazardous substance from the casing. <br />Extend to the ground surface and covered with a locked waterproof cap. <br />Capable of meeting S.J. Co. PHS-EHD Well Standards. <br />Leak interception and detection system shall prevent the leaked hazardous substance from <br />entering ground water. <br />14. INTERSTITIAL SPACE MONITORING <br />A. Visual monitoring [Section 2632 (c) (1)l <br />(a) Exterior surface and floor beneath tank monitored by direct viewing <br />(b) Daily visual inspections <br />_ (c) Liquid level in tank to be recorded at time of inspection <br />_ (d) If liquid observed around or beneath primary tank, owner will determine if an unauthorized release <br />has occurred. <br />B. Mechanical or electronic monitoring [Section 2632 (c) (2)) <br />(a) Continuous monitoring system connected to an audible and visual alarm system. <br />Monitoring equipment to be installed <br />Manufacturer- <br />Model Number:_ <br />Sensor Type: VaporLiquid Both. <br />ogMk <br />Sensor/Panel specifications. <br />Location(s) for sensors: <br />Tank: Piping' <br />Dispenser' <br />C. Monitoring and response plan submitted [Section 2632 (d) (1) & (2)]. <br />15. Any special accessories, fittings, coatings, or linings not inherent within the initial design of the 10 tank or <br />double-wall UST. [Section 2631 (b)] <br />A. Approved by a nationally recognized independent testing organization. <br />B. Demonstration of integrity with the primary and/or. secondary containment. <br />2 <br />