COMPLIANCE INFO_2006-2008 - Laserfiche WebLink

Home Browse Search

19255517888 Main Fax GETTLER RYAN INC 8:34 p.m. 04-23-2008 8112 For EMV models a. Remove 1/4-inch pipe plug from tank test port in the ® if flow is restricted to about 3 gpm(11 ipm)or less Packer (on 6-inch Big-Flo applications, remove the with the nozzle open, the leak detector has not 1/4-inch pipe plug from the riser/flange assembly). opened. Repeat step Sa with increased running b. Apply a UL-classified non-toxic pipe thread sealant to time of pump to insurethe purging of all air.All air the 1/4-inch NPT 45-degree elbow and install in tank must be purged from the system or the leak test port of the packer. On 6-inch Big-Flo applications, detector will restrict flow to about 3 gpm(11 1pm). the 1/4-inch NPT 45-degree elbow may be installed 9. Affix the enclosed decals to the dispenser dial glass on grade into the riser/flange assembly. of gasoline upon which the leak detector is being installed. c. Apply UL-classified non-toxic pipe thread sealant to Additional decals are available; call customer service at the 1/4-inch NPT hex nipple and install on 45-degree 1-800-262-7539. elbow that is in the tank test port(or on 6 inch Big-Flo 10. Inspect all threaded joints to assure they are tight and not riser/flange assembly. leaking. d. Apply a UL-classified non-toxic pipe thread sealant to the 1/4-inch NPT tee and install on the hex nipple to Test of the Leak Detector accommodate both the vent tube and the snap tap. U.S. Environmental Protection Agency (EPA) regulations require e. Apply a UL-classified non-toxic pipe thread sealant to the threads of the 1/4-inch NPT 90-degree elbow vent annual verification of operation of leak detector. To assure tube fitting and install in the tee. maintenance of leak detection capability, Red Jacket requires that UL-classified non-toxic pipe thread sealant to operation of the mechanical leak detector be verified by testing upon f. Apply a UL- start-up and that testing of the leak detector be performed routinely at the threads cl the 1/4-inch NPT straight vent tube least annually. fitting and install in the leak detector vent opening in the cap of the leak detector. g. Install the vent tubing into both fittings and tighten per s Test procedure options for mechanical leak instructions on package. detectors are explained in Red Jacket Engineering P $ Reports,RJ20 and RJ21.The Red Jacket Snap Tap h. To install snap tap connectors in FX2V/FX2DV Connectors allow the FX2V/FX2DV leak detector models, apply a UL-classified non-toxic pipe thread to be tested with the FXV Snap Tap Tester as an sealant to the snap tap connectors and install one in the option to the above test methods.See Red Jacket body of the FXV leak detector and the other in the tee literature #042-111-1 for test instructions using attached to the hex nipple attached to the 45-degree Snap Tap Connectom elbow installed in the tank test port of the packer.On 6- 11. The top cover on the Red Jacket leak detector is designed to inch Big-Flo applications, install the two snap tap accommodate a sealing wire which can be used to connectors-one in the body of the FXV leak detector discourage tampering or the unauthorized removal of leak and one in the riser/flange assembly. detector.(See Figure 2). i. Attach and crimp loop of the retaining tether around the Snap Tap threads. ® It should be noted that if the dispensing system(the j. Replace the caps over the quick-connect couplings and solenoid valve and the nozzle)is opened previous to tighten snugly. the completion of the line test,the FXV Series will detect this opening as a leak and restricted flow DO NOT overtighlen. will result. Closing of the nozzle(s)for a period of time adequate to allow completion of the line test ® See technical bulletin#042-111-1 for use of Snap will allow the leak detector to open.Once opened, Tap Connector Assembly. full pump flow can be provided. 7. Connect power to pump at the load center. 8. Clear remaining air from system as follows: a. Tum on dispenser that is farthest from the leak detector but do not open nozzle.Wait 4 or 5 minutes or more. Look for leaks on parts worked on. b. Shut off the pump and allow it to stand four or five minutes. Then start the pump again and open the FX2V/FX2DVJ OL TETHERED nozzle farthest from the leak detector. CAP c. Continue to dispense enough gasoline,about 20 to 30 gallons(76 to 114 liters), to pump ALL air from the system. SNAP TAP 45°ELBOW Figure 1 a o , O o SEALING WIREi t 114-INCH •1 (provided by contractor) QI T-FITTING (o VENTTLIBE Figure 2 �'J