Laserfiche WebLink
CAPACITY <br />COMPOSITION <br />PRODUCT 1 1 <br />U. L. LISTED <br />COMPATIBILITY WITH 1 <br />METHANOL <br />13. TANK(s) TO BE INSTALLED <br />A. Stsul-elad with fiberg as reinforced plastic. <br />® B. Holt test requir Immediately before "setting" t (s) (35, - 40, volts). tion (b) t4!] <br />C. Fiberglass [Sect 2635 (3) and 2631 (p)] <br />(1) Striker plate dimensions and materials. <br /><2) Striker plata r all accessible Ings. <br />(3 Installation instructions require an air test and soap bubble test prior to fristattation. <br />Non�cl steel tank [Section 2635 (b)] <br />(1) Cathodic protection providedfor entire tank, piping components (tuts, bolts, washers, <br />etc.). <br />(2) Approved by a corrosion engineer or N.A.C.E. technician. <br />® (3) Document stating inspection method and frequency (mini semi - t I Cion it t). <br />13 <br />ANk <br />UST SYSTEM <br />PRINTSET <br />INFORMATION <br />1, <br />v <br />Four complete sets of plans (To include specification sheets snVor equipment brochures if not on file). <br />2. <br />Plans drawn to scale in non-eresable, print. <br />3. <br />Plot plan to show location and number of tanks. <br />4. <br />Tank cross-sectional diagram included an prints submitted. <br />S. <br />ci <br />Detail of tank, piping system, excavation and cover. <br />6. <br />Tank(s) and piping approved by a nationatty recognf2ed independent testing organization. (Title 23, Subehimpter 16, <br />,� <br />Article 3, Sec. 2631 (r) 9 26351 <br />T. <br />Verification of product cavatfbftfty with the tank(s), piping, monitoring <br />device(s), epoxy or silicone glues, etc. [Section 2635 (b) (2)] <br />8. <br />✓ <br />Manufacturer's written installation Instructions for tank(s), piping, monitoring devices, etc. Maction 2635 (b) (5)] <br />9. <br />Tightness Test (NFPA 30) is required an both primary (10) and secondary (20) containment system before covering. <br />[Section 2635 (b) (6) & (7)] <br />10. <br />t•'` <br />Doubt* welled tanks using pressure or vacuum testing to monitor the annuter spece. tion 2M (b) Ml <br />11. <br />NFPA 329 "Precision Test" required upon completion of installation with tank in operating condition. Test results to <br />be submitted directly to PHS/EHD from the testing company or owner of facility. [Health i Safety Code, Division 20, <br />Chapter 6.7, Section 25291 (g)] <br />12. <br />-IF <br />TANK COMMITION <br />IF -TANKS <br /># # # # # <br />CAPACITY <br />COMPOSITION <br />PRODUCT 1 1 <br />U. L. LISTED <br />COMPATIBILITY WITH 1 <br />METHANOL <br />13. TANK(s) TO BE INSTALLED <br />A. Stsul-elad with fiberg as reinforced plastic. <br />® B. Holt test requir Immediately before "setting" t (s) (35, - 40, volts). tion (b) t4!] <br />C. Fiberglass [Sect 2635 (3) and 2631 (p)] <br />(1) Striker plate dimensions and materials. <br /><2) Striker plata r all accessible Ings. <br />(3 Installation instructions require an air test and soap bubble test prior to fristattation. <br />Non�cl steel tank [Section 2635 (b)] <br />(1) Cathodic protection providedfor entire tank, piping components (tuts, bolts, washers, <br />etc.). <br />(2) Approved by a corrosion engineer or N.A.C.E. technician. <br />® (3) Document stating inspection method and frequency (mini semi - t I Cion it t). <br />13 <br />