INSTALL_2020 - Laserfiche WebLink

Home Browse Search

UL/ULC t ® " A Piping System SPECIFICATION 1 Primary Piping SECTION 1 - Scope This section covers the use of fiberglass reinforced plastic 2.06 Acceptable Manufacturers - NOV Fiber Glass (FRP) pipe for single wall fuel handling and fuel handling vent Systems, 501 -568-4010, or approved equal, and vapor applications Including gasoline, unleaded gasoline, gasoline/alcohol mixtures, blo-diesel , DEF and diesel up to Section 3 - Material and Construction '.. 150OF and 250 psig cyclic pressure , 3.01 2"- 4" Pipe - The pipe shall be manufactured by the filament winding process using an amine cured epoxy SECTION 2 - General Conditions thermosetting resin to Impregnate strands of continuous 2.01 Coordination - Material furnished and work glass filaments, which are wound around a mandrel at a '.. performed under this section shall be coordinated with the 543/4' winding angle under controlled tension . The pipe '.. related work and equipment specified under other sections, shall be heat cured and the cure shall be confirmed using a i.e. Valves, Flexible Connectors, Equipment, Differential Scanning Calorimeter. Pipe shall be supplied with a T. A. B . "' (Threaded and 2.02 Governing Standards - Except as modified or Bonded) ends. supplemented herein, all materials and construction methods Pipe shall have a minimum continuous cyclic pressure shall comply with and be tested in accordance with the rating of 125 psig at 150°F in accordance with ASTM D2992, following standards and test methods: Procedure A or UL 971 pressure rating . Standards and Test Methods All pipe shall be 100% hydrotested at the factory before shipment at a minimum pressure of 265 psig and shall be UL971 Standard for Nonmetallic Underground Piping for Flam- UL971 -2004 Listed and labeled. 2004 mable Liquids '... 3.02 ASTM D2310 Classlf!cations fat 73.40F) ASTM Standard Classification for Machine-Made "Fiberglass" 251 - 3" RTRP-11AF D2310 (Glass Fiber Reinforced Thermosetting Resin) Pipe '.. ASTM Standard practice for obtaining Hydrostatic or Pressure 4" RTRP-11AH D2992 Design Basis for "Fiberglass' (Glass Fiber Reinforced ( Mechanical properties cell classifications shown are Thermosetting Resin) Pipe and Fittings minimums.) 3.03 Fittings - All fittings shall be manufactured using 2 .03 Operatina Conditions - In addition to the above the same type of material as the pipe . Fittings may be listed minimum design requirements, the system shall meet manufactured either by compression molding , filament the following minimum operating conditions: winding, resin transfer molding or contact molding methods. All fittings, adapter, and sump penetrations shall be UL971 - a. Operating Pressure 2004 Listed . b. Fluid Conveyed Fittings shall be adhesive bonded matched tapered bell c. Test Pressure and spigot. 3.04 Connections - Connections to flex connectors or 2.04 Quality Assurance - Pipe manufacturer's quality other piping materials shall be made by the use of NPT program shall be In compliance with ISO 9001 and/or API Q1 . (National Pipe Thread) threaded adapters or flanges bonded to the FRP piping system. 2.05 Delivery. Storage and Handling - Pipe and fittings 3.05 Sump Penetrations - Sump penetrations shall be shall be protected from damage due to Impact and point made by means of a permanently bonded FRP coupling. The loading. Pipe shall be properly supported to avoid damage coupling shall be capable of adjusting for the slope of the due to flexural strain . The contractor shall not allow dirt, piping system entering or exiting the sump wall, debris or other extraneous materials to get into pipe and 3.06 Adhesives - Adhesives shall be manufacturer's fittings. All factory machined areas shall be protected from standard for the piping system specified. sunlight until installed , is V w ,fgspips .com fgspipe@nov.com NW Fiber Glass Systems