|
PLUMBING GENERAL NOTES
<br />1.SEE ARCHITECTURAL DRAWINGS FOR BUILDING DIMENSIONS AND EXACT LOCATIONS OF PLUMBING FIXTURES.
<br />2.COORDINATE LOCATION OF PIPING WITH OTHER TRADES ON THIS PROJECT.
<br />3.CONCEAL ALL PIPING IN WALL FURRING, PARTITIONS, ETC., EXCEPT AT MECHANICAL ROOMS.
<br />4.PROVIDE BALL VALVES ON WATER PIPE BRANCHES TO EQUIPMENT AND PLUMBING FIXTURES. PROVIDE ACCESS PANELS
<br />WHEN LOCATED IN FURRED SPACES OR ABOVE NON-REMOVABLE CEILINGS. ALL VALVES SHALL BE FULL LINE SIZE.
<br />5.SEAL ALL PIPE PENETRATIONS THRU FLOORS WATERTIGHT.
<br />6.PROVIDE GAS SHUT-OFF VALVE, UNION AND DIRT LEG AT EACH GAS CONNECTION TO MECHANICAL EQUIPMENT.
<br />7.DOMESTIC HOT WATER HEATERS SHALL BE SEISMICALLY SECURED TO BUILDING STRUCTURE WITH ADEQUATE
<br />STRUCTURAL SUPPORT WITH ANCHOR BOLTS TO WITHSTAND 0.29 LATERAL AND VERTICAL LOADS.
<br />8.PRIOR TO ANY SOLENOID VALVE, QUICK CLOSING VALVE, ETC. PROVIDE AND INSTALL SHOCK ABSORBER OF REQUIRED
<br />SIZE.
<br />9.PENETRATIONS OF RATED ASSEMBLIES SHALL BE FIRE-STOPPED. FIRE STOPPING SHALL BE AN APPROVED MATERIAL OF
<br />THE ENFORCING AGENCY.
<br />10.OFFSET VENTS THRU ROOF 10 FEET MINIMUM FROM AIR INTAKES AND 4 FEET FROM OUTSIDE WALLS.
<br />11.CONDENSATE DRAIN LINE CONNECTIONS TO MECHANICAL UNITS SHALL INCLUDE MINIMUM 4" DEEP "P" TRAP AND
<br />CLEANOUTS AT ALL OFFSETS.
<br />12.ALL MECHANICAL UNITS ARE SHOWN FOR REFERENCE AND COORDINATION ONLY. SEE "M" SHEETS.
<br />13.OFFSET ALL RISERS AND DROPS TO AVOID PENETRATIONS AT TOP PLATES.
<br />14.FIELD VERIFY EXACT SIZES, LOCATIONS AND ELEVATIONS OF ALL PIPING CONNECTIONS, OTHER WORK, ETC., PRIOR TO
<br />TRENCHING OR INSTALLING OF ANY NEW WORK.
<br />15.BUILDING SEWER, WATER AND STORM DRAIN RUN APPROXIMATELY 5' MIN. FROM BUILDING, SECTION 15400 APPLIES TO
<br />UTILITIES IN THE BUILDING, UNDER THE BUILDING AND TO 5' OUTSIDE THE BUILDING, BEYOND THE 5' OUTSIDE OF THE
<br />BUILDING SECTION 02700 GOVERNS.
<br />16. CONTRACTOR TO COORDINATE PLUMBING REQUIREMENTS FOR FOOD SERVICE EQUIPMENT. REFER TO PLUMBING NOTES
<br />ON SHEET FS2.00.
<br />FIRESTOPPING
<br />1. PACK THE ANNULAR SPACE BETWEEN THE PIPE SLEEVES AND THE PIPE THROUGH ALL FLOORS AND WALLS WITH
<br />UL LISTED FIRE STOP, AND SEALED AT THE ENDS. ALL PIPE PENETRATIONS SHALL BE UL LISTED, HILTI, 3M
<br />PRO-SET, OR EQUAL.
<br />A.INSTALL FIRE CAULKING BEHIND MECHANICAL SERVICES INSTALLED WITHIN FIRE RATED WALLS, TO
<br />MAINTAIN CONTINUOUS RATING OF WALL CONSTRUCTION.
<br />2. PROVIDE SPECSEAL SYSTEMS UL FIRE RATED SLEEVE/COUPLING PENETRATORS FOR EACH PIPE PENETRATION OR
<br />FIXTURE OPENING PASSING THROUGH FLOORS, WALLS, PARTITIONS OR FLOOR/CEILING ASSEMBLIES. ALL
<br />PENETRATORS SHALL COMPLY WITH UL FIRE RESISTANCE DIRECTORY (LATEST EDITION), AND IN ACCORDANCE
<br />WITH CHAPTER 7, CBC REQUIREMENTS.
<br />3. SLEEVE PENETRATORS SHALL HAVE A BUILT IN ANCHOR RING FOR WATERPROOFING AND ANCHORING INTO
<br />CONCRETE POURS OR USE THE SPECIAL FIT CORED HOLE PENETRATOR FOR CORED HOLES.
<br />4. COPPER AND STEEL PIPING SHALL HAVE SPECSEAL PLUGS ON BOTH SIDES OF THE PENETRATOR TO REDUCE
<br />NOISE AND TO PROVIDE WATERPROOFING.
<br />5. ALL ABOVE SYSTEMS TO BE INSTALLED IN STRICT ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS. 6.
<br />ALTERNATE FIRESTOPPING SYSTEMS ARE ACCEPTABLE IF APPROVED EQUAL. HOWEVER, ANY DEVIATION FROM
<br />THE ABOVE SPECIFICATION REQUIRES THE CONTRACTOR TO BE RESPONSIBLE FOR DETERMINING THE
<br />SUITABILITY OF THE PROPOSED PRODUCTS AND THEIR INTENDED USE, AND THE CONTRACTOR SHALL ASSUME
<br />ALL RISKS AND LIABILITIES WHATSOEVER IN CONNECTION THEREWITH.
<br />MEP COMPONENT ANCHORAGE NOTE
<br />ALL MECHANICAL, PLUMBING, AND ELECTRICAL COMPONENTS SHALL BE ANCHORED AND INSTALLED PER THE DETAILS
<br />ON THE DSA APPROVED CONSTRUCTION DOCUMENTS. WHERE NO DETAIL IS INDICATED, THE FOLLOWING
<br />COMPONENTS SHALL BE ANCHORED OR BRACED TO MEET THE FORCE AND DISPLACEMENT REQUIREMENTS
<br />PRESCRIBED IN THE 2016 CBC, SECTIONS 1616A.1.18 THROUGH 1616A.1.26 AND ASCE 7-10 CHAPTER 13, 26 AND 30.
<br />1. ALL PERMANENT EQUIPMENT AND COMPONENTS.
<br />2. TEMPORARY OR MOVABLE EQUIPMENT THAT IS PERMANENTLY ATTACHED (e.g. HARD WIRED) TO THE
<br />BUILDING UTILITY SERVICES SUCH AS ELECTRICITY, GAS OR WATER.
<br />3. MOVABLE EQUIPMENT WHICH IS STATIONED IN ONE PLACE FOR MORE THAN 8 HOURS AND HEAVIER THAN 400
<br />POUNDS ARE REQUIRED TO BE ANCHORED WITH TEMPORARY ATTACHMENTS.
<br />THE FOLLOWING MECHANICAL AND ELECTRICAL COMPONENTS SHALL BE POSITIVELY ATTACHED TO THE STRUCTURE,
<br />BUT THE ATTACHMENT NEED NOT BE DETAILED ON THE PLANS. THESE COMPONENTS SHALL HAVE FLEXIBLE
<br />CONNECTIONS PROVIDED BETWEEN THE COMPONENT AND ASSOCIATED DUCTWORK, PIPING, AND CONDUIT.
<br />A. COMPONENTS WEIGHING LESS THAN 400 POUNDS AND HAVE A CENTER OF MASS LOCATED 4 FEET OR LESS
<br />ABOVE THE ADJACENT FLOOR OR ROOF LEVEL THAT DIRECTLY SUPPORT THE COMPONENT.
<br />B. COMPONENTS WEIGHING LESS THAN 20 POUNDS, OR IN THE CASE OF DISTRIBUTION SYSTEMS, LESS THAN 5
<br />POUNDS PER FOOT, WHICH ARE SUSPENDED FROM A ROOF OR FLOOR OR HUNG FROM A WALL.
<br />FOR THOSE ELEMENTS THAT DO NOT REQUIRE DETAILS ON THE APPROVED DRAWINGS, THE INSTALLATION SHALL BE
<br />SUBJECT TO THE APPROVAL OF THE DESIGN PROFESSIONAL IN GENERAL RESPONSIBLE CHARGE OR STRUCTURAL
<br />ENGINEER DELEGATED RESPONSIBILITY AND THE DSA DISTRICT STRUCTURAL ENGINEER. THE PROJECT INSPECTOR
<br />WILL VERIFY THAT ALL COMPONENTS AND EQUIPMENT HAVE BEEN ANCHORED IN ACCORDANCE WITH ABOVE
<br />REQUIREMENTS.
<br />PIPING, DUCTWORK & ELECTRICAL
<br />DISTRIBUTION SYSTEM BRACING NOTE
<br />OPTION 2: SHALL COMPLY WITH THE APPLICABLE OSHPD PRE-APPROVED (OPM #)
<br />#0043-13 BY MASON INDUSTRIES, INC.
<br />MECHANICAL PIPING (MP), MECHANICAL DUCTS (MD), PLUMBING PIPING (PP), ELECTRICAL DISTRIBUTION
<br />SYSTEMS (E):
<br />MP
<br />MP
<br />MP
<br />MD
<br />MD
<br />MD
<br />PP
<br />PP
<br />PP
<br />E
<br />E
<br />PIPING, DUCTWORK, AND ELECTRICAL DISTRIBUTION SYSTEMS SHALL BE BRACED TO COMPLY WITH THE FORCES
<br />AND DISPLACEMENTS PRESCRIBED IN ASCE 7-10 SECTION 13.3 AS DEFINED IN ASCE 7-10 SECTION 13.6.5.6,
<br />13.6.7, 13.6.8, AND 2016 CBC, SECTIONS 1616A.1.23, 1616A.1.24, 1616A.1.25 AND 1616A.1.26.
<br />THE METHOD OF SHOWING BRACING AND ATTACHMENTS TO THE STRUCTURE FOR THE IDENTIFIED DISTRIBUTION
<br />SYSTEM ARE AS NOTED BELOW. WHEN BRACING AND ATTACHMENTS ARE BASED ON PREAPPROVED
<br />INSTALLATION GUIDE (e.g., SMACNA OR OSHPD OPM). COPIES OF THE BRACING SYSTEM INSTALLATION GUIDE
<br />OR MANUAL SHALL BE AVAILABLE ON THE JOBSITE PRIOR TO THE START OF AND DURING THE HANGING AND
<br />BRACING OF THE DISTRIBUTION SYSTEMS. THE STRUCTURAL ENGINEER OF RECORD SHALL VERIFY THE
<br />ADEQUACY OF THE STRUCTURE TO SUPPORT THE HANGER AND BRACE LOADS.
<br />OPTION 3: SHALL COMPLY WITH THE SMACNA SEISMIC RESTRAINT MANUAL. OSHPD
<br />EDITION (2009), INCLUDING ANY ADDENDA. FASTENERS AND OTHER ATTACHMENTS
<br />NOT SPECIFICALLY IDENTIFIED IN THE SMACNA SEISMIC RESTRAINT MANUAL, OSHPD
<br />EDITION, ARE DETAILED ON THE APPROVED DRAWINGS WITH PROJECT SPECIFIC NOTES
<br />AND DETAILS. THE DETAILS SHALL ACCOUNT FOR THE APPLICABLE SEISMIC HAZARD
<br />LEVEL ____ AND CONNECTION LEVEL ____ FOR THE PROJECT AND CONDITIONS.
<br />OPTION 1: DETAILED ON THE APPROVED DRAWINGS WITH PROJECT SPECIFIC NOTES
<br />AND DETAILS
<br />R GPR
<br />GW GREASE WASTE PIPINGGW
<br />GAS PRESSURE REGULATOR
<br />IW
<br />MG
<br />OH
<br />(N) , (E)
<br />(NTS)
<br />OFL
<br />OD
<br />IW
<br />MG
<br />OFL
<br />DESCRIPTION
<br />ABOVE CEILING
<br />ABOVE FLOOR , BELOW FLOOR
<br />ABOVE FINISHED FLOOR
<br />BALL VALVE
<br />BRANCH - BOTTOM CONNECTION
<br />BRANCH - TOP CONNECTION
<br />ACCESS DOOR , ACCESS PANEL
<br />ABBREVIATION
<br />AF , BF
<br />AFF
<br />ABC
<br />SYMBOL
<br />BV
<br />AD , AP
<br />PLUMBING LEGEND
<br />WH
<br />P & TRV
<br />RV or P&TRV
<br />PRV
<br />RWL
<br />(R) , (D)
<br />SD
<br />W OR SS
<br />RD
<br />P & TRV
<br />SD
<br />RWL
<br />TP
<br />UN
<br />TYP
<br />V
<br />WHA
<br />VB
<br />WCO
<br />TP
<br />V , VR , VTR
<br />CAP ON END OF PIPE
<br />BRANCH - SIDE CONNECTION
<br />COLD WATER
<br />CONDENSATE DRAIN LINE
<br />COP
<br />or
<br />CW
<br />CD
<br />CO
<br />CD
<br />EXISTING TO BE REMOVED
<br />FIXTURE UNIT
<br />FLOOR DRAIN
<br />FLOOR SINK
<br />FLOOR CLEANOUT
<br />FLOW IN DIRECTION OF ARROW
<br />FINISHED FLOOR ELEVATION
<br />FCO
<br />FS
<br />FD
<br />FU
<br />FF=
<br />CO CLEANOUT CO
<br />POC
<br />INDIRECT DRAIN , CONDENSATE DRAIN
<br />MEDIUM PRESSURE GAS
<br />NEW , EXISTING
<br />NOT TO SCALE
<br />OVERHEAD
<br />PRESSURE & TEMPERATURE RELIEF VALVE PIPING
<br />RECESSED BOX HOSE BIBB OR WALL HYDRANT
<br />RELIEF VALVE OR PRESSURE & TEMPERATURE RELIEF VALVE
<br />RISER DOWN (ELBOW)
<br />RISER UP (ELBOW)
<br />PRESSURE REDUCING VALVE
<br />RISE , DROP
<br />SOIL, WASTE OR SANITARY SEWER
<br />STORM DRAIN
<br />OVERFLOW RAINWATER LEADER
<br />VENT PIPING
<br />UNION OR FLANGE
<br />TRAP PRIMER
<br />TRAP PRIMER PIPING
<br />TYPICAL
<br />VENT , VENT RISER , VENT THRU ROOF
<br />VALVE IN VALVE BOX
<br />WATER HAMMER ARRESTER
<br />VALVE IN RISER (TYPE AS INDICATED OR NOTED)
<br />POINT OF CONNECTION, NEW TO EXISTING
<br />SOLENOID VALVE WITH MOTOR ACTUATOR
<br />WALL CLEANOUT
<br />RAINWATER LEADER
<br />ROOF DRAIN
<br />OVERFLOW DRAIN
<br />GAS - LOW PRESSURE
<br />GAS COCK , PLUG COCK
<br />FLUSH VALVE , FLUSH TANK
<br />FROM ABOVE , TO ABOVE
<br />FROM BELOW , TO BELOW
<br />GATE VALVE, BALL VALVE, SHUT OFF VALVE
<br />HOSE BIBB
<br />GRADE CLEANOUT, EXTERIOR
<br />GALLONS PER MINUTE
<br />HOT WATER PIPING
<br />G
<br />GSCK , PC
<br />(FA) , (TA)
<br />(FB) , (TB)
<br />FV , FT
<br />G
<br />GCO
<br />GPM
<br />HB
<br />HW
<br />PUMPED CONDENSATE DRAINPCDPCD
<br />HOT WATER RETURNHWR
<br />&CW & HW FIXTURE CONNECTION STUB OR ANGLE STOP
<br />DN DOWN
<br />UG UNDERGROUND
<br />UR URINAL
<br />S or SK SINK
<br />IE or INV INVERT ELEVATION
<br />L LAVATORY SINK
<br />LL, DL LONGEST LENGTH (GAS), DEVELOPED LENGTH
<br />WC WATER CLOSET
<br />WH WALL HYDRANT
<br />WSFU WATER SUPPLY FIXTURE UNIT
<br />DFU DRAIN FIXTURE UNIT
<br />ELECTRIC WATER HEATEREWH
<br />EXISTING TO REMAIN(E)
<br />FU
<br />EXISTING TO BE ABANDONED, CAP WHERE SHOWN(E)
<br />BELOW FINISHED FLOORBFF
<br />(FA) , (TA)
<br />(FB) , (TB)
<br />FV , FT TABLE 2.1
<br />GAS LOAD COMPUTATION
<br />BUILDING EQUIPMENT EQUIPMENT DESCRITION MBH EACH QTY MBH TOTAL MBH
<br />TOTAL/GPR
<br />BDEF WAC-B1 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-D1 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-D2 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-E1 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-E2 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-E3 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-E4 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-F1 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-F2 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-F3 MECHANICAL AC UNIT 1.00 50 50.00
<br />BDEF WAC-F4 MECHANICAL AC UNIT 1.00 50 50.00
<br />BRANCH 1 550.00
<br />///////////////////////////////////////
<br />KITCHEN P5 OPEN BURNER WITH OVEN 1.00 163 163.00
<br />KITCHEN P7 TILT SKILLET 1.00 144 144.00
<br />KITCHEN P8 STEAMER 2.00 60 120.00
<br />KITCHEN P9 DOUBLE STACK OVEN 2.00 63 126.00
<br />KITCHEN P10 DOUBLE STACK OVEN 2.00 60 120.00
<br />KITCHEN GWH-A1 GAS WATER HEATER 1.00 200 200.00
<br />KITCHEN (E)AC-10 MECHANICAL AC UNIT 1.00 250 250.00
<br />KITCHEN AC UNIT MECHANICAL AC UNIT 1.00 200 200.00
<br />BRACH 2 1323.00
<br />TOTAL 1873.00
<br />MIN METER
<br />CAPACITY 3000.00
<br />SHEETSOF730 Howe Avenue, Suite 450Sacramento, CA 95825Phone: 916.921.2112Fax: 916.921.2212KITCHEN RENOVATIONJOE SERNA SCHOOLSHEET NO.
<br />CONSULTANT
<br />UPDATED
<br />CADFILE
<br />CHECKED
<br />DRAWN
<br />SCALE
<br />PROJECT NO.
<br />DATE
<br />REVISIONS BY
<br />19-32-050
<br />RL
<br />TD
<br />AS NOTED
<br />191009.00
<br />PM - DESIGN TEAM PROJECT NO.
<br />MCM - RL/JSV
<br />C A
<br />RANCHO CORDOVA,CALIFORNIA
<br />ENGINEERING CONSULTANTS, INC.
<br />P I T A L
<br />\\capsac.lan\network\Project_Docs\2019\191009.00\1200 Drawings\1205 AutoCAD Project Files\P0.1.dwg - April 10, 2020 12:46 PM - Joel Valencia04/10/2020
<br />FILE NO. 39-50 APP NO. 02-118041
<br />P0.1 PLUMBING LEGEND,SCHEDULE & NOTES
|