|
AIR DISTRIBUTION SCHEDULE EQUIPMENT ANCHORAGE NOTES MECHANICAL SPECIFICATIONS MECHANICAL LEGEND
<br /> IDENTIFICATION STAMP
<br /> SYMBOL TYPE DESCRIPTIONSYMBOL ITEM ABBR. DIV. OF THE STATE ARCHITECT
<br /> ALL MECHANICAL, PLUMBING, AND ELECTRICAL COMPONENTS SHALL BE ANCHORED AND A. THIS CONTRACTOR SHALL COMPLY WITH ALL CODES AND REGULATIONS IN EFFECT AT THE JOB SITE, INCLUDING, BUT
<br /> INSTALLED PER THE DETAILS ON THE DSA APPROVED CONSTRUCTION DOCUMENTS. NOT LIMITED TO: ® SUPPLY AIR SA APP. 02-117806 INC: 3
<br /> CEILING MODULAR CORE DIFFUSER WITH FRAME FOR LAY-IN T-BAR WHERE NO DETAIL IS INDICATED, THE FOLLOWING COMPONENTS SHALL BE ANCHORED OR A.1. 2016 CALIFORNIA BUILDING CODE RETURN AIR RA REVIEWED FOR
<br /> OO SUPPLY MOUNTING BRACED TO MEET THE FORCE AND DISPLACEMENT REQUIREMENTS PRESCRIBED IN THE A.2. 2016 CALIFORNIA MECHANICAL CODE ® EXHAUST AIR EA SS p FLS 0 ACS El
<br /> TITUS MODEL MCD 2016 CBC, SECTIONS 1616A.1 .18 THROUGH 1616A.1 .26 AND ASCE 7-10 CHAPTER 13, A.3. 2016 CALIFORNIA PLUMBING CODE
<br /> 26 AND 30. ® OUTSIDE AIR OSA DATE: 03/03/2020
<br /> CEILING EGGCRATE GRILLE WITH 1/2"x1/2"x1/2" GRID, FRAME FOR A.4. 2016 CALIFORNIA ELECTRICAL CODE TRANSFER AIR TA
<br /> O RETURN/TAG LAY-IN T-BAR MOUNTING. 1. ALL PERMANENT EQUIPMENT AND COMPONENTS. A.5. 2016 CALIFORNIA GREEN BUILDING STANDARDS
<br /> TITUS MODEL 50F. 2. TEMPORARY OR MOVABLE EQUIPMENT THAT IS PERMANENTLY ATTACHED (E.G. A.6. 2016 CALIFORNIA BUILDING ENERGY EFFICIENCY STANDARDS - TITLE 24 DETAIL DESIGNATION
<br /> CEILING MODULAR CORE DIFFUSER WITH FRAME FOR SURFACE HARD WIRED) TO THE BUILDING UTILITY SERVICES SUCH AS ELECTRICITY, GAS A.7. NATIONAL FIRE PROTECTION ASSOCIATIONM11 DETAIL NUMBER
<br /> O SUPPLY MOUNTING OR WATER. A.8. CALIFORNIA STATE FIRE MARSHAL SHEET NO. WHERE SHOWN
<br /> TITUS MODEL MCD 3. MOVABLE EQUIPMENT WHICH IS STATIONED IN ONE PLACE FOR MORE THAN 8 B. ALL MATERIALS AND EQUIPMENT INSTALLED UNDER THIS CONTRACT SHALL BE GUARANTEED FREE FROM ALL
<br /> / / / HOURS AND HEAVIER THAN 400 POUNDS OR HAS A CENTER OF MASS MECHANICAL, ELECTRICAL AND WORKMANSHIP DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF FINAL -EQUIPMENT DESIGNATION
<br /> CEILING EGGCRATE GRILLE WITH 1 2x1 2x1 2 GRID, FRAME FOR LOCATED 4 FEET OR MORE ABOVE THE ADJACENT FLOOR OR ROOF LEVEL AC
<br /> ACCEPTANCE. THE CONTRACTOR SHALL BE RESPONSIBLE FOR REPAIRING OR REPLACING ALL DAMAGED ITEMS INSTALLED UNIT ABBREVIATION
<br /> SURFACE MOUNTING. THAT DIRECTLY SUPPORT THE COMPONENT ARE REQUIRED TO BE ANCHORED
<br /> RETURN/TAG 1
<br /> TITUS MODEL 50F. WITH TEMPORARY ATTACHMENTS. UNDER THIS CONTRACT WITHOUT ADDITIONAL COST TO OWNER. NUMBER
<br /> �
<br /> C. THE MECHANICAL CONTRACTOR SHALL PROVIDE THE OWNER COPIES OF OPERATION MAINTENANCE AND PREVENTATIVE
<br /> CEILING � GRILLE DESIGNATION w
<br /> EXHAUST/ SINGLE DEFLECTION, FIXED BLADE, 35° DEFLECTION, 3/4" THE FOLLOWING MECHANICAL AND ELECTRICAL COMPONENTS SHALL BE POSITIVELY MAINTENANCE MANUALS FOR EACH MODEL AND TYPE OF MECHANICAL EQUIPMENT. i�NECK SIZE & BLOW
<br /> O BLADE SPACING, FRAME FOR SURFACE MOUNTING, OBD. ATTACHED TO THE STRUCTURE, BUT THE ATTACHMENT NEED NOT BE DETAILED ON THE D. CHECK AND VERIFY EXISTING CONDITIONS AT THE JOB SITE BEFORE BEGINNING WORK. ADJUST THE LOCATION AND O1ox10-3 (4 UON)
<br /> SIDEWALL
<br /> TITUS MODEL 350RL. 12o Fo_--FIRE DAMPER WHERE REQ'D �
<br /> RETURN PLANS. THESE COMPONENTS SHALL HAVE FLEXIBLE CONNECTIONS PROVIDED BETWEEN CONFIGURATION OF THE WORK NECESSARY TO SUIT ACTUAL CONDITIONS AND OTHER TRADES. ANY CHANGES REQUIRED �--CFM o
<br /> DUCT DOUBLE DEFLECTION, INDIVIDUALLY ADJUSTABLE BLADES WITH THE COMPONENT AND ASSOCIATED DUCTWORK, PIPING, AND CONDUIT. MUST FIRST BE APPROVED BY THE ARCHITECT OR ENGINEER. _--- ACOUSTIC LINED DUCT L V °
<br /> FO MOUNT 3/4" SPACING FOR DUCT MOUNTING. AIR SCOOP DAMPER E. THE LOCATIONS OF EQUIPMENT, PIPING, DUCTWORK AND SYSTEMS SHOWN ON THE DRAWINGS ARE DIAGRAMMATIC AND (�
<br /> SUPPLY EXTRACTOR. TITUS MODEL S300FL. A. COMPONENTS WEIGHING LESS THAN 400 POUNDS AND HAVE A CENTER OF SHALL BE FOLLOWED AS CLOSELY AS POSSIBLE. CHANGES REQUIRED TO SUIT EXISTING CONDITIONS AND DUE TO t TURNING VANES TV
<br /> MASS LOCATED 4 FEET OR LESS ABOVE THE ADJACENT FLOOR OR ROOF COORDINATION WITH OTHER TRADES SHALL BE MADE AT NO EXTRA COST TO THE OWNER. L�.� DUCT FLEXIBLE CONNECTION o
<br /> DOUBLE DEFLECTION AIRFOIL BLADES, ADJUSTABLE, FRONT LEVEL THAT DIRECTLY SUPPORT THE COMPONENT.
<br /> SIDEWALL F. ' DUCT RISER
<br /> SUPPLY
<br /> GO BLADES PARALLEL TO SHORT DIMENSION, WITH 3/4 BLADE B. COMPONENTS WEIGHING LESS THAN 20 POUNDS, OR IN THE CASE OF
<br /> 0
<br /> SPACING, SURFACE MOUNTING, OBD. TITUS MODEL 272RS. DISTRIBUTED SYSTEMS, LESS THAN 5 POUNDS PER FOOT, WHICH ARE G. DURING CONSTRUCTION PROVIDE TEMPORARY CLOSURES OF METAL OR TAPED POLYETHYLENE ON OPEN DUCTWORK TO DUCT DROP a
<br /> SUSPENDED FROM A ROOF OR FLOOR OR HUNG FROM A WALL. PREVENT CONSTRUCTION DUST FROM ENTERING DUCTWORK SYSTEM. �--I W9 771R
<br /> SIDEWALL EGGCRATE GRILLE WITH 1/2"x1/2%1/2" GRID, FRAME FOR SURFACE H. ALL BRANCH DUCTS SHALL HAVE BALANCING DAMPERS WITH ACCESSIBLE LOCKING TYPE QUADRANT. WHERE DAMPER IS RECTANGULAR TO ROUND FITTING � ll rti
<br /> O RETURN/TAG MOUNTING. TITUS MODEL 50R. REFER TO THE MECHANICAL PLANS FOR NECK FOR THOSE ELEMENTS THAT DO NOT REQUIRE DETAILS ON THE APPROVED DRAWINGS, VOLUME CONTROL DAMPER VD V �J
<br /> INACCESSIBLE PROVIDE YOUNG REGULATOR MODEL 270-301 CABLE KIT WITH EITHER 830A-CC (RECTANGULAR) OR I-I
<br /> SIZE, CFM, AIR DIFFUSION PATTERN, AND FIRE DAMPER (IF REQUIRED) THE INSTALLATION SHALL BE SUBJECT TO THE APPROVAL OF THE DESIGN PROFESSIONAL 5020-CC (ROUND) DAMPER. FD FIRE DAMPER W/ ACCESS FD a/
<br /> IN GENERAL RESPONSIBLE CHARGE OR STRUCTURAL ENGINEER DELEGATED a
<br /> OWALL SIGHT-PROOF EXTRUDED ALUMINUM WALL LOUVER WITH J RESPONSIBILITY AND THE DSA DISTRICT STRUCTURAL ENGINEER. THE PROJECT I. PERFORM TOTAL SYSTEMS BALANCE IN ACCORDANCE WITH AABC, ASHRAE STD 111, OR NEBB PROCEDURAL STANDARDS FSD FIRE SMOKE DAMPER W/ ACCESS FSD
<br /> L LOUVER STYLE, 45° BLADES AND BIRD SCREEN. COLOR BY ARCHITECT. INSPECTOR WILL VERIFY THAT ALL COMPONENTS AND EQUIPMENT HAVE BEEN ANCHORED FOR TESTING, BALANCING AND ADJUSTING OF ENVIRONMENTAL SYSTEMS. OPPOSED BLADE DAMPER OBD
<br /> GREENHECK MODEL ESD-603.
<br /> IN ACCORDANCE WITH ABOVE REQUIREMENTS. J. THE INSTALLATION OF DUCT SMOKE DETECTORS FOR AUTOMATIC SHUTDOWN OF AIR MOVING SYSTEMS AS REQUIRED BY BACKDRAFT DAMPER BDD V ~^ a
<br /> CMC SECTION 608 OR AS REQUIRED FOR THE OPERATION OF FIRE SMOKE DAMPERS SHALL COMPLY WITH THE 0 H a
<br /> NOTES: REQUIREMENTS OF THE LOCAL FIRE DEPARTMENT'S STANDARD "FIRE PROTECTION DESIGN GUIDELINES FOR SMOKE MOTORIZED DAMPER V 1 1 v
<br /> 1 . EQUIVALENT MODELS OF TUTTLE & BAILEY, KRUEGER, ENVIROMENTAL AIR PRODUCTS, OR J & J ARE CONTROL WITHIN BUILDINGS". WHERE AIR DUCT SMOKE DETECTORS SERVING AIR-MOVING SYSTEMS ARE INSTALLED O THERMOSTAT® +48'AFF MAX TO TOP OF BOX T-STAT V 1 I--I 1
<br /> ACCEPTABLE. REFER TO THE MECHANICAL PLANS FOR NECK SIZE, CFM, AIR DIFFUSION PATTERN, AND FIRE WITHIN CONDCEALED SPACES, AND/OR DROP CEILING AREAS, THE DETECOR SHALL BE PROVIDED WITH THE UNIT h--i
<br /> DAMPER, IF REQUIRED. OS SENSOR A +48'AFF MAX TO TOP OF BOX 0 Q
<br /> SERVED. SAID REMOTE ALARM LED DEVICE SHALL BE LABELED TO CLEARLY IDENTIFY THE UNIT SERVED (AC-1, ETC.). I--I
<br /> WHERE AIR DUCT SMOKE DETECTORS SERVING AIR-MOVING SYSTEMS ARE INSTALLED IN CONCEALED SPACES, AND/OR TC nMECLOCK ® +48'AFF MAX TO TOP OF BOX
<br /> PIPING AND DUCTWORK DISTRIBUTION SYSTEM DROP CEILING AREAS MORE THAN 10 FEET ABOVE THE FINISHED FLOOR, THE DETECTOR SHALL BE PROVIDED WITH A TCP TEMPERATURE CONTROL PANEL TCP ~D
<br /> REMOTE TEST AND RESET SWITCH, SAID REMOTE TEST AND RESET SWITCH SHALL BE ATTACHED TO AN ADJACENT WALL U b
<br /> BRACING NOTES so DUCT SMOKE DETECTOR SD o
<br /> INDOOR UNIT SCHEDULE OR STRUCTURAL COLUMN AT A MAXIMUM HEIGHT OF 6 FEET ABOVE FINISHED FLOOR. PRIOR TO MECHANICAL PERMIT PIPE RISER �i
<br /> FINAL, A SMOKE DETECTOR SHUT-OFF TEST WILL BE REQUIRED. /DROP (R)/(D)
<br /> ELECTRICAL 0 ABOVE FINISHED FLOOR AFF � N
<br /> COOLING HEATING OPERATING PIPING, DUCTWORK, AND ELECTRICAL DISTRIBUTION SYSTEMS SHALL BE BRACED TO O
<br /> TYPE MARK MOUNTING DRIVE CFM OSA CFM CAPACITY CAPACITY SERVICE WEIGHT MFGR MODEL NOTES COMPLY WITH THE FORCES AND DISPLACEMENTS PRESCRIBED IN ASCE 7-10 SECTION UNLESS OTHERWISE NOTED UON
<br /> VOLT PHASE (BTUH) (BTUH) (LBS.) 13.3 AS DEFINED IN ASCE 7-10 SECTION 13.6.5.6, 13.6.7, 13.6.8, AND 2016 CBC, TYPICAL (TYP) b
<br /> SECTIONS 1616A.1 .24, 1616A.1 .25 AND 1616A.1 .26.
<br /> INDOOR UNIT POWERED BY OUTDOOR UNIT. ELECTRICAL CONTRACTOR TO PROVIDE
<br /> BOTTOM OF DUCT BOD J
<br /> IDU 1 WALL 208 1 DIRECT 655 - 27,300 36,200 SEE PLAN 50 FUJITSU ASU24RLF DISCONNECT SWITCH. PROVIDE PROGRAMMABLE THERMOSTAT. THE METHOD OF SHOWING BRACING AND ATTACHMENT TO THE STRUCTURE FOR THE BOTTOM OF PIPE BOP ~ 'Z
<br /> IDENTIFIED DISTRIBUTION SYSTEM ARE AS NOTED BELOW. WHEN BRACING AND AUTOMATIC AIR VENT AAV
<br /> ATTACHMENTS ARE BASED ON A PRE-APPROVED INSTALLATION GUIDE (E.G., SMACNA OR
<br /> 7
<br /> OSHPD OPM), COPIES OF THE BRACING SYSTEM INSTALLATION GUIDE OR MANUAL SHALL MANUAL AIR VENT MAV H
<br /> INDOOR UNIT POWERED BY OUTDOOR UNIT. ELECTRICAL CONTRACTOR TO PROVIDE BE AVAILABLE ON THE JOBSITE PRIOR TO THE START OF AND DURING THE HANGING AND TEMP. CONTROL CONTRACTOR TCC
<br /> DISCONNECT SWITCH. PROVIDE PROGRAMMABLE THERMOSTAT. BRACING OF THE DISTRIBUTION SYSTEMS. THE STRUCTURAL ENGINEER OF RECORD TEMPERATURE CONTROL VALVE TCV ^ Q
<br /> IDU 2 WALL 208 1 DIRECT 655 - 27,300 36,200 SEE PLAN 50 FUJITSU ASU24RLF SHALL VERIFY THE ADEQUACY OF THE STRUCTURE TO SUPPORT THE HANGER AND BRACE r 1
<br /> LOADS. COMBUSTION AIR CA V 0
<br /> TRANSFER AIR GRILLE TAG '
<br /> MECHANICAL PIPING (MP), MECHANICAL DUCTS (MD), PLUMBING PIPING (PP), ELECTRICAL NEW N o
<br /> DISTRIBUTION SYSTEMS (E): )
<br /> (
<br /> OUTDOOR UNIT SCHEDULE EXISTING (E) a
<br /> ELECTRICAL Y MP MD PP E OPTION 1: DETAILED ON THE APPROVED DRAWINGS WITH PROJECT $ POINT OF DIS/CONNECTION POD/POC rl
<br /> ODU SEER
<br /> / COOLING HEATINGOPERATING = ® ® [71 [71SPECIFIC NOTES AND DETAILS.
<br /> --- HEATING HOT WATER SUPPLY HHWS
<br /> TYPE MARK TYPE VOLT VOLT PHASE MCA MOCP EER HSPF CAPACITY CAPACITY SERVICE WEIGHT MFGR MODEL NOTES
<br /> (BTUH) (BTUH) (LBS.) o P MP MD PP E OPTION 2: SHALL COMPLY WITH THE APPLICABLE OSHPD PRE-APPROVAL ----- HEATING HOT WATER RETURN HHWR
<br /> o El El El (OPM#) #0043-13. 2-WAY CONTROL VALVE
<br /> ELECTRICAL CONTRACTOR TO PROVIDE DISCONNECT SWITCH. LOCKOUT HEATING m VERIFY OPM#
<br /> PROP MODE. MP MD PP OPTION 3: SHALL COMPLY WITH THE SMACNA SEISMIC RESTRAINT MANUAL, BACKFLOW PREVENTER BFP „
<br /> ODU 1 FAN ROOF 208 1 18 30 19.5/12.5 10.6 27,300 36,200 SEE PLAN 160 FUJITSU AOU24RLXFW1 ❑ ❑ ❑ OSHPD EDITION (2009), INCLUDING ANY ADDENDA. FASTENERS AND BALL VALVE
<br /> OTHER ATTACHMENTS NOT SPECIFICALLY IDENTIFIED IN THE SMACNA BUTTERFLY VALVE
<br /> SEISMIC RESTRAINT MANUAL, OSPHD EDITION, ARE DETAILED ON THE
<br /> ELECTRICAL CONTRACTOR TO PROVIDE DISCONNECT SWITCH. LOCKOUT HEATING APPROVED DRAWINGS WITH PROJECT SPECIFIC NOTES AND DETAILS. THE CAP
<br /> PROP MODE. DETAILS SHALL ACCOUNT FOR THE APPLICABLE SEISMIC HAZARD LEVEL �` CHECK VALVE
<br /> ODU 2 FAN ROOF 208 1 18 30 19.5/12.5 10.6 27,300 36,200 SEE PLAN 160 FUJITSU AOU24RLXFW1 ___- AND CONNECTION LEVEL __-- FOR THE PROJECT AND y
<br /> CONDITIONS. AUTOMATIC BALANCE VALVE ABV
<br /> (B&G ULTRA SET)
<br /> AUTOMATIC BALANCE VALVE CBV
<br /> (B&G CIRCUIT SETTER)
<br /> EXHAUST FAN SCHEDULE CONTROL VALVE (2-WAY)
<br /> ELECTRICAL
<br /> OPERATING
<br /> FLEX CONNECTOR FC
<br /> TYPE MARK FAN MOUNTING CFM E.S.P. DRIVE FAN RPM SONES SERVICE CONTROL WEIGHT MFGR MODEL NOTES FLOW ARROW
<br /> TYPE VOLT PHASE HP WATTS IN W.C. (LBS.)
<br /> GATE VALVE
<br /> PRESSURE GAUGE
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY PLUG VALVE
<br /> CEF 1 CENTRIFUGAL CEILING 115 1 - - 100 0.25 DIRECT 940 1.0 SEE PLAN INTERLOCK 15 GREENHECK SP-110-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER.
<br /> W/ LIGHTS REDUCER
<br /> STRAINER
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY M�] TEMPERATURE SENSOR TS MEEHLEIS
<br /> CEF 2 CENTRIFUGAL CEILING 115 1 - - 125 0.2 DIRECT 1041 1.2 SEE PLAN INTERLOCK 15 GREENHECK SP-130-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER. T TEST PORT (PETE'S PLUG) PP MODULAR
<br /> W/ LIGHTS THERMOMETER BUILDINGS, INC.
<br /> TRIPLE DUTY VALVE A DESIGN BUILD
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY COMPANY
<br /> CEF 3 CENTRIFUGAL CEILING 115 1 - - 100 0.25 DIRECT 940 1.0 SEE PLAN EMS 15 GREENHECK SP-110-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER.
<br /> CONTROLS
<br /> 13 03 E. LODI AVE.
<br /> LODI, CA. 95240
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY (209) 334-4637
<br /> REF 1 CENTRIFUGAL ROOF 115 1 0.25 - 1,100 0.4 DIRECT 1147 8.2 SEE PLAN INTERLOCK 50 GREENHECK G-123-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER. PROVIDE CA. LIC. NO. 473488
<br /> W/ LIGHTS FACTORY CURB.
<br /> NV. LIC. NO. 37887
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY
<br /> REF 2 CENTRIFUGAL ROOF 115 1 0.25 - 1,100 0.4 DIRECT 1147 8.2 SEE PLAN INTERLOCK 50 GREENHECK G-123-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER. PROVIDE
<br /> W/ LIGHTS FACTORY CURB.
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY
<br /> REF 3 CENTRIFUGAL ROOF 115 1 0.1 - 425 0.4 DIRECT 1390 6.2 SEE PLAN EMS 35 GREENHECK G-090-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER. PROVIDE
<br /> CONTROLS FACTORY CURB.
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY
<br /> REF 4 CENTRIFUGAL ROOF 115 1 0.1 - 425 0.4 DIRECT 1390 6.2 SEE PLAN EMS 35 GREENHECK G-090-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER. PROVIDE
<br /> CONTROLS FACTORY CURB.
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY
<br /> REF 5 CENTRIFUGAL ROOF 115 1 0.25 - 725 0.4 DIRECT 1292 8.5 SEE PLAN EMS 45 GREENHECK G-099-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER. PROVIDE
<br /> CONTROLS FACTORY CURB.
<br /> PROVIDE BACK-DRAFT DAMPER. PROVIDE MOUNTING KIT. PROVIDE FACTORY
<br /> REF 6 CENTRIFUGAL ROOF 115 1 0.25 - 725 0.4 DIRECT 1292 8.5 SEE PLAN EMS 45 GREENHECK G-099-VG PRE-WIRED DISCONNECT SWITCH. PROVIDE WITH SPEED CONTROLLER. PROVIDE
<br /> CONTROLS FACTORY CURB.
<br /> DRAWN: AT
<br /> CHECKED: J D
<br /> REVISIONS:
<br /> 01/03/20 DSA CORRECTIONS
<br /> MECHANICAL SHEET INDEX DATE MAY 1312019
<br /> JOB NO. 19720
<br /> SHEET NO. SHEET TITLE SHEET TITLE
<br /> M-0.1 MECHANICAL NOTES &SCHEDULES
<br /> M-0.2 MECHANICAL SCHEDULES MECHANICAL NOTES &
<br /> M-0.3 MECHANICAL DETAILS
<br /> M-1.1 MECHANICAL FLOOR PLAN SCHEDULES
<br /> M-2.1 MECHANICAL SECTIONS
<br /> M-3.1 MECHANICAL ROOF PLAN
<br /> MEP Et FS / Sustainability / CxA QRQFESS/av SHEET NO.
<br /> All DE
<br /> 1209 Pleasant Grove Blvd.
<br /> Roseville, CA 95678
<br /> e p 916-771-0778
<br /> REN. 12-31- 1 * m 0
<br /> CONSULTING www.lpengineers.com `rx CHAN\CP� �P
<br /> Project Navigator PA I -Project file5\20 19 LP Projects\19-206 I Meehleis- Tokay 15 Gym\Mechanical\MP Sheets\192305 MO I (Mech Cover).dwg 1/30/2020 2: 1 1 PM
<br /> ENGINEERS Job#: 19-2061 qTF OF CA0F���
<br /> 1 92305_MO_1 (Mech Cover).dwg 01/30/20 2:1 1 :54pm Ashton
<br />
|