COMPLIANCE INFO_2019 - Laserfiche WebLink

Home Browse Search

RedThread"' 11A Piping System wl� (Specification Guide) APPLIES TO:T01-T35 Section 1-Scope arewound around a mandrel at a 543/4 winding angle under controlled tension.Pipeshall be heat cured and the cure shall be This section covers the use of fiberglass reinforced plastic(FRP)pipe for confirmed using a Differential Scanning Calorimeter. single wall fuel hand ling and fuel handlingventand vapor applications including gasoline,unleaded gasoline,gasoline/alcohol mixtures, Pipe shall be supplied with a T.A.B'"(Threaded and Bonded) bio-diesel,DEF and diesel up to 150°F and 250 psig cyclic pressure. ends. Pipe shall have a minimum continuous cyclic pressure rating of Section 2-General Conditions 125 psigat 150°F in accordance with ASTM D2992,Procedure A or 2.01 Coordination-Material furnished and work performed underthis UL 971 pressure rating. section shall be coordinated with the related work and equipment All pipe shall be 100%hydrotested at the factory before shipment specified under other sections,i.e.Valves,Flexible Connectors, ata minimum pressure of 265 psig and shall be UL971-2004 Equipment. Listed and labeled. 2.02 Governing Standards-Exceptasmodifiedorsupplemented 3.02 ASTM D2310Classifications(at 73.4°F) herein,all materialsand construction methodsshall complywith and betested in accordancewith the following standards and test 2"-3" RTRP-11AF methods: 4" RTRP-11AH Standard and Test Methods (Mechanical properties cell classifications shown are minimums.) 3.03 Fittings-All fittingsshall be manufactured usingthe same type UL9712004 Standard for Nonmetallic Underground Pipingfor Flammable of material as the pipe.Fittings maybe manufactured either by Liquids compression molding,filament winding,resin transfer molding ASTM D2310 Standard Classification for Machine-Made"Fiberglass"(Glass Fiber or contact molding methods.All fittings,adapter,and sump Reinforced Thermosetting Resin)Pipe penetrations shall be UL971-2004 Listed. Standard Test Method for Obtaining Hydrostatic or Pressure Design Fittings be adhesive bonded matched tapered bell and ASTM D2992 Basis for"Fiberglass"(Glass-Fiber-Reinforced-Thermosetting Resin) g P Pipe and Fittings Spigot. 3.04 Connections-Connections to flex connectors or other piping 2.03 Operating Conditions-In addition to the above minimum materials shall be made by the use of NPT(National Pipe Thread) design requirements,the system shall meet the following threaded adapters or flanges bonded to the FRP piping system. minimum operating conditions: 3.05 Sump Penetrations-Sump penetrations shall be made by a.Operating Pressure means of a permanently bonded FRP coupling.The coupling shall be capable of adjusting for the slope of the piping system b.Operating Temperature entering or exiting the sump wall. c.Fluid Conveyed 3.06 Adhesives-Adhesives shall be manufacturer's standard forthe pi ping system specified. d.Test Pressure 2.04 Quality Assurance-Pipe manufacturer's quality program shall Section 3-Materials and Construction be in compliance with ISO 9001 and/orAPl Ql. 3.012"-4"Primary and 3"-6"Secondary Pipe-The pipe shall be 2.05 Delivery,Storage and Handling-Pipe and fittings shall be manufactured by the filamentwinding process using anamine protected from damage due to impact and point loading.Pipe cured epoxy thermosetting resin to impregnate strands of shall be properly supported to avoid damage due to flexural continuous glass filaments,which arewound around a mandrel strain.The contractor shall not allow dirt,debris or other at a 543/4"winding angle under controlled tension.The pipe extraneous materials to get into pipe a nd fittings.All factory shall be heat cured a nd the cure shall be conf irmed using a machined a reas sh a[I be protected from su n light u nti[installed. Differential Scanning Calorimeter. 2.06AcceptableManufacturers-Fiber Glass Systems,(501) Pipe shaI[besupplied with aT.A.B!"(Threaded and Bonded)or 568-4010,or approved equal. plain ends. Pipe shall have a minimum continuous cyclic pressure rating of Section 3-Materials and Construction 125 psigat150°Fin accordance with ASTM D2992,ProcedureAor UL 971 pressure rating. 3.012"-4"Pipe-The pipe shall be manufactured by the filament All pipe,both primary and secondary,shall be 100%hydrotested winding process using an amine cured epoxy thermosetting at the factory before shipment at a minimum pressure of 265psig resin to impregnate strands of continuous glass filaments,which and shall beUL971-2004 Listed and Labeled. Fiber Glass Systems I KOYProductlon5olutions fgspipe@nov.com nov.com/fgs