INSTALL_2020 - Laserfiche WebLink

Home Browse Search

RED THREAD011 Piping System GENERAL SPECIFICATIONS SECTION 1 -Scope 2.03 Operating Conditions - In addition to the above This section covers the use of fiberglass reinforced plastic listed minimum design requirements, the system shall (FRP) pipe for mild chemical and water services up to 210OF meet the following minimum operating conditions: and 450 psig steady pressure. a.Operating Pressure The piping system shall be furnished and Installed complete b.Operating Temperature with all fittings,Joining materials,supports,specials,and other c. Fluid Conveyed necessary appurtenances. d.Test Pressure SECTION 2-General Conditions 2.04 Qualft Assurance- Pipe manufacturer's qual- 2.01 Coordination - Material furnished and work per- ity program shall be in compliance with ISO 9001 and/ formed under this section shall be coordinated with related or API Q1. work and equipment specified under other sections. Valves Section 2.05 Delivery. Storage. and Handling- Pipe and fit- Supports Section tings shall be protected from damage due to impact and Equipment Section point loading. Pipe shall be properly supported to avoid dam- age due to flexural strains. The contractor shall not allow dirt, 2.02 Governing Standards-Except as modified or sup- debris, or other extraneous materials to get into pipe and plemented herein, all materials and construction methods fittings. All factory machined areas shall be protected from shall comply with the applicable provisions of the following sunlight until Installed. specifications and be tested using the following standards: 2.06 Acceptable Manufacturers - NOV Fiber Glass Standard Specifications Systems,501-568-4010,or approved equal. ASTM Standard Specification for Filament-Wound "Fiberglass" (Glass-Fiber-Reinforced-Ther- mosetting SECTION 3- Materials and Construction D2996 Resin) Pipe 3.01 2"-24" Pipe -The pipe shall be manufactured by ASTM Standard Specification for Reinforced the filament winding process using an amine cured epoxy 4024 Thermosetting Resin (RTR) Flanges thermosetting resin to impregnate strands of continuous glass Standard Specification for "Fiberglass" filaments,which are wound around a mandrel at a 543/4 wind- ASTM (Glass-Fiber-Reinforced-Thermosetting- ing angle under controlled tension. Pipe shall be heat cured D5685 Resin) Pressure Pipe Fittings and the cure shall be confirmed using a Differential Scanning Calorimeter. Standard Test Methods Standard Practice for Obtaining Hydrostatic Pipe shall be supplied with a matching tapered bell and a ASTM or Pressure Design Basis for "Fiberglass" matching tapered spigot. D2992 (Glass-Fiber-Reinforced-Thermosetting Resin) Pipe and Fittings Pipe shall have a minimum continuous steady pressure rat- ASTM Standard Practice for Measuring Beam ing of 225 psig at 210`F in accordance with ASTM D2992 D2925 Deflection of Reinforced Thermosetting Procedure A. Plastic Pipe Under Full Bore Flow ASTM Standard Test Method for ShortTime Hy- All pipe shall be 100%hydrotested at the factory before ship- D1599 draulic Failure Pressure of Plastic Pipe,Tub- ment at a minimum pressure of 300 psig. ing and Fittings Standard Test Method for Longitudinal Ten- 3.02 Flanges and Fittings -All fittings shall be manu- ASTM sile Properties of "Fiberglass" (Glass-Fiber- factured using the same type materials as the pipe. Fittings D2105 Reinforced Thermosetting Resin) Pipe and may be manufactured either by compression molding, spray- Tube Standard Test Method for Determination of up/contact molding, or filament winding methods. ASTM External Loading Characteristics of Plastic D2412 Pipe by Parallel-Plate Loading VWWWAgspipe.com 2700 West 65th Street 25 S.Main Street NOV Fiber Glass ftstems Little Rock,Arkansas 72209 Sand Springs,Oklahoma 74063 Phone:1 (501)568-4010 1 (918)245-6651