WORK PLANS - Laserfiche WebLink

Home Browse Search

- IMPORTANT- NUT STL ZINC .375 16 A A I I I A FOR SE OF ASSEMBLY- THE USE OF FURNITURE DOLLIES S RECOMMENDED TO ASSEMBLE THIS KIT. • 1 .50 I I 0 WSHR FLAT .375 GENERAL HOLE LAYOUT I F ANCHOR-D RING TIE DOWN 0.375 DIA STEP 1 -4 • �� BOLT-#3/8- 16 X 31N I ► ►► DRILL HOLES IN CASE AND FLOOR r \� r NOTE: FLOOR ANCHORS SHALL BE: 3.50 C77 I I A) FRONT FRAME ANCHORS: ONE PER FRONT BRACKET, — — — — • ONE BRACKET PER "L" FRAME 2.25 1) '/2"-13 X 4" THREADED ROD - ASTM A 193 GRADE B7 STEEL, DETAIL I WITH '/2" GRADE 5 WASHER, AND NUT EVEN WITH EDGE • 2) MIN 2.75" EMBEDMENT INTO 4" MIN CONCRETE SLAB USING HILTI HIT-RE500 V3 TWO PART EPDXY, FOLLOWING ALL THE I I `--- NUT-HEX 3/8- 16 STEEL ZINC PLT MANUFACTURER'S DIRECTIONS. B) REAR CABLE ANCHORS: TWO ANCHORS PER TIE DOWN ASSEMBLY. ONE CABLE ASSEMBLY PER EVERY "L" FRAME #3/8 16 x 4 IN 1) 3/8-16 X4" THREADED ROD - ASTM A193 GRADE B7 STEEL THREADED ROD 2 PER TIE DOWN, USING HILTI HIT-RE500 V3 TWO PART EPDXY, FOLLOWING ALL THE MANUFACTURER'S DIRECTIONS. e 2) MIN 2.75" EMBEDMENT INTO 4" MIN CONCRETE SLAB 1 .38 e O ® STEP 4.) EPDXY THE '/2" THREADED STEP 1 .) g - RODS TO THE FLOOR. AT EVERY REAR UPRIGHT MARK AND DRILL 7/ 16" HOLES FOR THE • LOOSELY ATTACH THE UPRIGHT TIE-DOWN AS SHOWN IF NOT ALREADY DRILLED. ATTACH THE FRONT BRACKET TO THE TIE-DOWN TO THE UPRIGHTS WITH THE 3/8" X 3" BOLTS, NUTS AND ° FLOOR WITH THE '/2" NUT WASHERS AS PROVIDED. • • o , o PROVIDED (AT THIS TIME) OR ATTACH THE STEP 2.) BRACKET AT THE LATER MARK THE LOCATION OF THE CASE LINE-UP ON THE FLOOR, USING THE • • ' g - STEP (PAGE 6) APPROXIMATE HOLE LOCATIONS SHOWN. DRILL THE HOLES FOR THE • REAR FLOOR TIE DOWNS (USES 3/8 in. THREADED RODS) , AND THE REAR TIE DOWN FRONT BRACKETS — (USES '/2 in. THREADED ROD) ACCORDING TO THE DETAIL H EPDXY MANUFACTURER'S SPEC FOR THE DRILL DIAMETER NEEDED- .50 WWW.HILTI.COM SEE NOTES FOR DRLL DEPTH REQUIRED. 28.62 30.45 28.71 2.25 STEP 3.1 ALL HOLE DIM'S ARE APPROXIMATE AND FOR REFERENCE ONLY EPDXY THE 3/8" THREADED RODS INTO THE HOLES AND ATTACH THE .50 ° MEASURE ALL DIM'S OFF ACTUAL CASE82 REAR TIE-DOWNS TO THE FLOOR WITH THE WASHER AND NUTS .68 68 .68 6.08 FLANGE PROVIDED. O O O 0 0;;v] O O ::=I O O — EPDXY WORKABILTY r - - - - - - - - - - - - - - - - - - - - - - - - I ° N° ° ° I CHART PER HILTI.COM I I I I I I � III I I I I I I I I II l; I I;II I I I I �� L` - - - - - - - - - - - - - - - - - - - - - - - - - - - - - _ '�: , ► WL S5877 x ° I 0 I ° ° I I ° 00 126.44 OF CAL � I I 4. . 82 50 min - - - - - - - - - - - - - - - - - - - - - - - - - - - - - I I N I 88. . .41 25 min 1 .50 R �I 1 .50 I 42. . .60 16 min J� HUssmAn 51 . . . 68 i UNLESS OTHERWISE SPECIFIED I I I �� I �� I I 11 I 11, I IDIMENSIONS ARE IN INCHES. INSTRUCTION- - I� I ° 11110 ° ISI ° ° ISI ° I1l, I - 69. . . 86 4min o 25_ 0 0- 0 �#, # 0 0 0 ,#, 1 tJ w CD 0 0 I 87. . . 104 rein THIRD SEISMIC . 187 CABLE 0 0 � a» O O O O O 0 1 �� 7 - ANGLE w 0 0 0 0 1 .86 Ew PROJECTIONc/)RESTRAINT RFL P/N REV CD 25 1 .09 3117766 `D SHEET 4 OF 6 ACD