Laserfiche WebLink
� • e \ a STEP 5 ATTACHING THE CABLE <br /> l � <br /> WITH THE 1 /8" WIRE ROPE STEP 5 - 7 <br /> K � PROVIDED, MAKE THE LOOPS ATTACHING THE CABLE TO THE <br /> THROUGH THE REAR FLOOR TIE FLOOR AND REAR OF THE CASE. <br /> DOWNS AS SHOWN IN DETAIL J <br /> WITH 121 WIRE CLAMPS <br /> PROVIDED. SEQUENCE# 1 . <br /> NOTE: The CABLE must be <br /> oriented with the saddle on <br /> JN the long (LIVE) end and U- bolt <br /> on the short (DEAD) end as <br /> shown in the picture. <br /> 2 ROPE TURNBACK= 3 - 3/41, q�FRONTFRAME ANTE: FLOOR CHORS:ORSAON BE: <br /> FRONT BRACKET, <br /> 3 <br /> ONE BRACKET PER "L" FRAME <br /> EITHER TAPE THE EXCESS 1 17:'- 13 X 4" THREADED ROD - ASTM A 19 GRADE B7 STEEL, <br /> 1 CABLES TO THE WALL, OR WITH 7f GRADE 5 WASHER, AND NUT <br /> I 21 MIN 2.75" EMBEDMENT INTO 4" MIN CONCRETE SLAB USING <br /> DRAPETHEM OVER THETOP OF HILTI HIT-RE500 V3 TWO PART EPDXY, FOLLOWING ALL THE <br /> 1 � THE CASE. YOU WILL NEED TO MANUFACTURER'S DIRECTIONS. <br /> DETAIL K ACCESS THE CABLES ONCE BI REAR CABLE ANCHORS: TWO ANCHORS PER TIE DOWN ASSEMBLY. <br /> \ , ONE CABLE ASSEMBLY PER EVERY "L" FRAME <br /> THE CASE IS PUSHED INTO ITS II 3/8- I6 X4" THREADED ROD - ASTM A 19 GRADE B7 STEEL <br /> \ FINAL POSITION, SO SECURE Z PER TIE DOWN, USING HILTI HIT-RE500 V3 TWO PART EPDXY, <br /> THEM ACCORDING TO YOURFOLLOWING ALL THE MANUFACTURER'S DIRECTIONS. <br /> � 21 MIN 2.75" EMBEDMENT INTO 4" MIN CONCRETE SLAB <br /> PREFERENCE. <br /> STEP 6. <br /> oe, <br /> LOWER THE CASE OVER THE <br /> • \ �qsF FRONT BRACKETS AND <br /> eqc� THREADED RODS AND SLIDE <br /> THE CASE INTO ITS FINAL <br /> POSITION, <br /> STEP 7. <br /> WORKING FROM ON TOP OF THE <br /> CASE, FEED THE CABLE FROM <br /> � THE FLOOR UP THROUGH THE <br /> IMPORTANT CABLE SPEC NOTE REAR UPRIGHT TIE-DOWN. PULL <br /> CABLE SHALL BE: CABLE TIGHT AND CLAMP OFF ,,.w, <br /> 1 /8" DIAMETER 7x19 GALVANIZED WIRE ROPE THE CABLE SIMILAR TO STEP 5 <br /> � - - --- - - �q�g - y- - - - - - - - --- - - � � - SEQUENCE 2 & 3 ' <br /> OF AL <br /> Turnback <br /> Dead End � NOTE. The CABLE must be <br /> oriented with the saddle on UNLESS OTHERWISE sPEciFieo Hussmanrp <br /> U —BOLT the long (LIVE) end and U - bolt DIMENSIONS ARE IN wcHes. INSTRUCTION- <br /> Live End I � on the short (DEAD) end as <br /> r - � shown in the picture. THIRD SEISMIC . 187 CABLE <br /> SADDLE DETAIL J ROPE TURNBACK= 3 - 3/4" PRo EcnoN RESTRAINT RFL <br /> ` " R` <br /> SHEET 5 of 6 3117766 A <br />