SR0082610 - Laserfiche WebLink

Home Browse Search

INSTALLATION (2 of 2) _ Tablet ,o Riser Height Needed Risers Required TELEG LIDE RISER(24 SERIES) 0-3-1/2" None(use adapter) INSTALLATION GUIDELINES >3-1/2'-22" SR24 Tools needed:7/16'Nut driver tool/bit(included),marker(included), Adapter >22' 37" LR24 tape:measure and drill with 1/2'chuck.Jigsaw,circular saw or reciprocating saw will be needed if risers need to be cut. NOTE:To remove a component or adjust its position,the Uppei Band Clamp needs to be loosened or removed using nut driver bit. Loosened clamps should be retightened to 5-8 ft lbs.of torque (same;as a rubber no-hub coupling).The Lower Band Clamp is SR24 factory set and should not be adjusted or removed. S1 10er Riser } Adapter Riser Assembly Instructions/Steps Riser 1. Set unit so the pipe connections line up with jobsite piping and Height measure riser height needed from top of cover to finished grade. Needed See*'able 1 to select risers needed. Riser 2. Remove covers from adapters.Remove adapters from main unit. Alignment Mark } On a level surface,pre-assemble the risers and adapters, - ---------- adjusting the components upwards or downwards to achieve; LR24 5' the riser height.needed.Make sure to maintain minimum and Long Riser maximum insertion depths as shown in Figure 2. If components __ Cut lino. _� 1 aro:too long,make a circular line around the sidewall with marker and cut with a power saw.The lowest rut line on the riser assembly will be 5"beyond the riser height needed to allow for ideal insertion depth(See Figure 1).An alignment mark should be drawn]'beyond the riser height needed which will align with the TeleGlide Riser top of the base unit gasket.DO NOT c:ut the alignment mark.The Adapters and risers should sit level with each other.Tighten Figurents upper clamps to keep riser/adapter assembly from shifting. Make alignment marks on the sidewalls at the top of all riser gaskets to aid final assembly. Cover 3. IMPORTANT:Before the next step, make sure both diffusers are installed inside the main unit at the appropriate locations. Check if there needs to be any flow control adjustment at the inlet diffuser(see general installation instructions). Adapter(shown) 4. Take apart riser assembly and clean all sidewalls and insides of or Riser gaskets to remove dust/debris.Install components into the main Gasket unit starting from the lowest riser and work your way up to finished grade.Maintain minimum and maximum insertion Upper Band Clamp depths for all components(see Figure 2).1 ighten Upper Clamps 2 1/2'Minimum Insertion Depth (field adjustable) to specified torque after correctly positioning components.Riser Lower Band Clamp assembly may need to be supported during backfill. - - - - -- - --- -- - - - - - (factory set-do not 4'Maximum Insertion Depth adjust or remove) b. If tilting of the adapter is required to be flush with grade,do so (into GB unit only) AFTER all clamps have been tightened with risers)/adaptor in a - - - - -- -- --- - - - - - - GB Unit(shown) vertical and level position.Tilting is done using gasket flexibility, or Riser Tilting before tightening clamps may ruin a perfect gasket seal. Schier recommends tilting only the adapter versus the entire riser assembly to make sure your riser height and proper tank Depths access is maintained. Figure 2-Insertion S. If riser height conditions change after completing above steps, there may be room for adjustment.As long as minimum and maximum insertion depths are maintained(see Figure 2),the adaptors/risers can be adjusted/cut as many times as necessary. When riser system installation is complete,see Leak/Seal Testing Anchor hook procedure if reqt aired(p3 of 5). UTI X NO EaCEPION TA.[Nx - —ODAREETIONSNOID ❑A[IfcrtD � Tvu AND REwaMn ANCHOR KIT INSTALLATION ]—,SRECIEED HEM Anchor Strep [HE"LNG IS ONLY IN EONTORTMNCI WITH THE MNG. CONCIAT M 111E M.1111 AND GENfMI COMVnANCE Stainless steel anchor kit is recommended for installation in high WRH THE INEORMANON GIVEN IN THE CONINA0 GOCUMfN15.AM 9110H SHOWN 15 SUNECY 10 111 water table conditions to prevent float out.Necessity to be Anchor plate, AFOUREMENTS OT THE PLANS AND SHFOtlUTIONS CONI.a0 IS.""w TOR GIMENNONS— determined by specifying engineer.Hold down force achieved by SHMI RE CONFIRMED AND COARELATIU AT THE Wa WE: COORDINATION Of HIS—MNTN THAT OE ALL OTHEA backfill weight acting on Anchor Plate. _ AADES AND'.I ATIE A DAY 11NIONMANCF U1 HIS WDR, TURLEY AND ASSOCIATES,INC Slide Anchor Hook over tie down point on end wall and bolt to 7431 CAPITOL AVENUE Anchor Strap.Bolt Anchor Strap to Anchor Plate using SACRAMENTO.CA 95616 p g provided - Brian Provencal stainless steel hardware.If required,Anchor Plate may be bolted to GATE 0e104rzo2o er concrete slab using provided holes. ANCHOR KIT INSTALLATION DETAIL r] SCHIER LIFETIME GUARANTEED MODEL NUMBER: DESCRIPTION:Polyethylene Grease Interceptor G B��Q 50 GPM 52 gallon capacity GREASEINTERCEPTO - PART n:4025 001-XX DWG BY:C.O'Boyle DATE:10/08/2015 REV:O J�201_ ECO: 0 Copyright 2015