WORK PLANS - Laserfiche WebLink

Home Browse Search

HCD SPCM FQQO PREPARATION UNIT CHECKLIST G-- —L , Kra Cite No FOR REFERNCE DPILY HSC Part 7 2 T25 CCR J Yes _ MECHANICAL HOODS–CCR T24 CMC§508 •Are hoods installed all: • Mechanical exhaust ventilation Deep fat fryers;broilers;fry grills;steam- equipment provided over all cooking §114149.1(a) Hoods jacketed kettles;hot-top ranges;ovens; CMC§508.1 equipment?As required to effectively §114149.1(b) B80s;rotisseries;dishwashing machines; remove: §114149.1(c) and,similar equipment in a food-processing Cooking odors;smoke;steam;grease; §114149.1(4) establishment? heat;and,vapors. MECHANICAL HOODS SEAMS/JOINTS–CCR T24 CMC§808 • Seams,joints,and penetrations of the hood enclosure–Do they have a fiquid-tight CMC§508.2 continuous external weld to the hood's lower INFPA 95:5.1.21 outermostperimeter? • Seams,joints,and penetrations–Permitted to be internally welded;is the weld is formed CMC 5508.21 smooth or ground smooth,so it doesn't trap INFPAW5.1.31 cease,and is cleanable? •Are the internal hood joints,seams,fitter support frames,and appurtenances CMC§508.22 attached inside the hood sealed or grease- INFPA95:&IA1 fight? •Are the penetrations are sealed by devices that are listed for such use and whose CMC 5508.23 presence does not detract from structural tWPA9e5.1.51 •All seams in the duct completely tight integrity? to prevent the accumulation of grease? •Are the listed exhaust hoods,with or without • Construction joints/seams tightly fitted exhaust dampers constructed of materials CMC§508.24 1 sealed so as to be easily cleanable. required by the listing? p1FPA9a51.q Silicone sealant or equivalent •Are the fisted exhaust hoods assembled in CMC§508.2.5 waterproof compounds are acceptable, accordance with the listing requirements? INFPA 96:&1.71 provided that the gap is smaller than •Are the eyebrow-type hoods over gas/ W and applied smooth so as to §114149.2(1) electric ovens(when permitted)have a duct prevent the entrance of liquid waste or §114301(2) Seams t constructed as required in§510.0 from the CMC§508.2.6 vermin §114149.2(1) flue(s)connected to the hood canopy p1FPA9a5.isil . All seams in the duct completely light §114301(2) Joints oven upstream lue of the exhaust? to prevent the accumulation of grease? • Construction joints!seams tightly fitted • Is the duct connecting the oven Bue(s)to the CMC§508.2.7 !sealed so as to be easily cleanable. hood canopy connected with continuous 09FRA9a5.1.d21 Silicone sealant or equivalent weld or have a duct-to-duct connection? waterproof compounds are acceptable, • Does the insulation materials other than provided that the gap is smaller than electrical insulation shall have aflame 1/0 and applied smooth so as to spread rating of 25 or less when tested in CMC§508.2.8 prevent the entrance of liquid waste or accordance with UL 723,Standard for Test INFPA95:5.1.91 vermin for Surface Burning Characteristics of Building Materials? . Does the adhesives or cements used in the insta0ation U insulating materials comply CMC§508.29 with the requirements of§508.2.8,when INFPA9e51.1aJ tested with the specific insulating material? •Are the penetrations sealed with rated CMC§506.2.10 devices in accordance with the J MC§508.2.1J requirements of 508.2.117 Are the devices that require penetration of .27 5061 the hood listed in accordance with UL 1978, pCMC C 508.11 1 Standard for Grease Ducts? EQUIPMENT ON ROOFS–CCR T24 CMC§903.8/304.0 Roof Access ' Equipment/appliances located on roofs or CMC§304.1 elevated locations are accessible? PNPPA5f:.9A3.11 WA WA Roof Support • Roofs with equipment are capable of CMC 303.8.12 WA WA supporting the additional load? . Is there a minimum of 6between any part Guards or of the equipment and the edge of the roof? CMC 303.8.1.5 WA WA Rails If not–Is there a guard or a tail a min of 42' tall on the exposed side? . If building height is more than 15'–Is roof CMC§304.1.2 NIA WA access from the inside? Inside • Is there a minimum of 6'between any part Access of the equipment and the edge of the root? 122 WA WA If not–Is there a guard or a rail a minimum §304.1.22 §304.19.4 of 42•tall on the exposed side? • Equipment has at least 30'working CMC Work Area Uearance in front of the service panel? §303.8.1.1 NIA WA Page 6 of 10