|
ACCESSIBILITY NOTES (CONT. )
<br /> CURB RAMPS (CONT.) PARKING CONT. LAVATORIES CONT.
<br /> 11B-406.5.1 LOCATION. CURB RAMPS AND THE FLARED SIDES OF CURB RAMPS "UNAUTHORIZED VEHICLES PARKED IN DESIGNATED ACCESSIBLE SPACES NOT 11B-606.5 EXPOSED PIPES AND SURFACES. WATER SUPPLY AND DRAIN PIPES
<br /> SHALL BE LOCATED SO THAT THEY DO NOT PROJECT INTO VEHICULAR TRAFFIC DISPLAYING DISTINGUISHING PLACARDS OR SPECIAL LICENSE PLATES ISSUED UNDER LAVATORIES AND SINKS SHALL BE INSULATED OR OTHERWISE
<br /> LANES, PARKING SPACES, OR PARKING ACCESS AISLES. CURB RAMPS AT MARKED FOR PERSONS WITH DISABILITIES WILL BE TOWED AWAY AT THE OWNER'S CONFIGURED TO PROTECT AGAINST CONTACT. THERE SHALL BE NO SHARP OR
<br /> CROSSINGS SHALL BE WHOLLY CONTAINED WITHIN THE MARKINGS, EXCLUDING EXPENSE. TOWED VEHICLES MAY BE RECLAIMED AT: ABRASIVE SURFACES UNDER LAVATORIES AND SINKS.
<br /> ANY FLARED SIDES. OR BY TELEPHONING
<br /> 11B-606.6 ADJACENT SIDE WALL OR PARTITION. LAVATORIES, WHEN LOCATED
<br /> 11B-406.5.2 WIDTH. THE CLEAR WIDTH OF CURB RAMP RUNS (EXCLUDING ANY BLANK SPACES SHALL BE FILLED IN WITH APPROPRIATE INFORMATION AS A ADJACENT TO A SIDE WALL OR PARTITION, SHALL BEA MINIMUM OF 18 INCHES
<br /> FLARED SIDES), BLENDED TRANSITIONS, AND TURNING SPACES SHALL BE 48 PERMANENT PART OF THE SIGN. (457 MM) TO THE CENTERLINE OF THE FIXTURE. ©2011 STARBUCKS COFFEE
<br /> INCHES (1219 MM) MINIMUM.
<br /> TOILET ROOMS 1113-606.7 SINK DEPTH. SINKS SHALL BE 6% INCHES(165 MM) DEEP MAXIMUM.
<br /> 1113-406.5.3 LANDINGS. LANDINGS SHALL BE PROVIDED AT THE TOPS OF CURB STARBUCKS COFFEE
<br /> RAMPS AND BLENDED TRANSITIONS. THE LANDING CLEAR LENGTH SHALL BE 48 11B-603 TOILET AND BATHING ROOMS SIGNS
<br /> INCHES (1219 MM) MINIMUM. THE LANDING CLEAR WIDTH SHALL BE AT LEAST AS COMPANY
<br /> WIDE AS THE CURB RAMP, EXCLUDING ANY FLARED SIDES, OR THE BLENDED 11B-603.2 CLEARANCES. CLEARANCES SHALL COMPLY WITH SECTION 11B-603.2. 11B-703 SIGNS
<br /> TRANSITION LEADING TO THE LANDING. THE SLOPE OF THE LANDING IN ALL 2401 UTAH AVENUE SOUTH
<br /> DIRECTIONS SHALL BE 1:48 MAXIMUM. 11B-603.2.1 TURNING SPACE. TURNING SPACE COMPLYING WITH SECTION 11B-703.2 RAISED CHARACTERS. RAISED CHARACTERS SHALL COMPLY WITH SEATTLE, WASHINGTON 98134
<br /> 11B-304 SHALL BE PROVIDED WITHIN THE ROOM. SECTION IIB-703.2 AND SHALL BE DUPLICATED IN BRAILLE COMPLYING WITH (206) 318-1575
<br /> 11B-406.5.11 GROOVED BORDER. CURB RAMPS SHALL HAVE A GROOVED BORDER SECTION I IB-703.3. RAISED CHARACTERS SHALL BE INSTALLED IN ACCORDANCE
<br /> 12 INCHES (305 MM)WIDE ALONG THE TOP OF THE CURB RAMP AT THE LEVEL 11B-603.2.2 OVERLAP. REQUIRED CLEAR FLOOR SPACES, CLEARANCE AT WITH SECTION IIB-703.4. THESE DRAWINGS AND SPECIFICATIONS ARE
<br /> SURFACE OF THE TOP LANDING AND AT THE OUTSIDE EDGES OF THE FLARED CONFIDENTIAL AND SHALL REMAIN THE SOLE
<br /> SIDES. THE GROOVED BORDER SHALL CONSIST OF A SERIES OF GROOVES '/ INCH FIXTURES, AND TURNING SPACE SHALL BE PERMITTED TO OVERLAP. PROPERTY OF STARBUCKS CORPORATION, WHICH IS
<br /> /4
<br /> (6.4 MM)WIDE BY' INCH (6.4 MM) DEEP, AT 3/4 INCH (19 MM) ON CENTER. 1113-703.2.1 DEPTH. RAISED CHARACTERS SHALL BE 1/32 INCH (0.8 MM) MINIMUM
<br /> 11B-603.2.3 DOOR SWING. DOORS SHALL NOT SWING INTO THE CLEAR FLOOR ABOVE THEIR BACKGROUND. THE OWNER OF THE COPYRIGHT IN THIS WORK.
<br /> SPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE. OTHER THAN THE DOOR THEY SHALL NOT REPRODUCED (IN WHOLE OR IN
<br /> 11B-406.5.12 DETECTABLE WARNINGS. CURB RAMPS AND BLENDED TRANSITIONS TO THE ACCESSIBLE WATER CLOSET COMPARTMENT, A DOOR, IN ANY 11B-703.2.2 CASE. CHARACTERS SHALL BE UPPERCASE. PART), SHARED WITH THIRD PARTIES IN AN
<br /> SHALL HAVE DETECTABLE WARNINGS COMPLYING WITH SECTION 11 B-705. MANNER ON OTHER PROJECTS OR EXXTT USEDENSIONS TO
<br /> POSITION, MAY ENCROACH INTO THE TURNING SPACE BY 12 INCHES (305 MM) THIS PROJECT WITHOUT THE PRIOR WRITTEN
<br /> MAXIMUM. 11B-703.2.3 STYLE. CHARACTERS SHALL BE SANS SERIF. CHARACTERS SHALL CONSENT OF STARBUCKS CORPORATION. THESE
<br /> PARKING SPACES NOT BE ITALIC, OBLIQUE, SCRIPT, HIGHLY DECORATIVE, OR OF OTHER UNUSUAL DRAWINGS AND SPECIFICATIONS ARE INTENDED TO
<br /> 11B-603.3 MIRRORS. MIRRORS LOCATED ABOVE LAVATORIES OR FORMS. EXPRESS DESIGN INTENT FOR A PROTOTYPICAL
<br /> 11B-502 PARKING SPACES COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE STARBUCKS STORE (WHICH IS SUBJECT TO CHANGE
<br /> REFLECTING SURFACE 40 INCHES (1016 MM) MAXIMUM ABOVE THE FINISH 11B-703.2.4 CHARACTER PROPORTIONS. CHARACTERS SHALL BE SELECTED AT ANYTIME)AND DO NOT REFLECT ACTUAL SITE
<br /> 11B-502.1 GENERAL. CAR AND VAN PARKING SPACES SHALL COMPLY WITH FLOOR OR GROUND. MIRRORS NOT LOCATED ABOVE LAVATORIES OR FROM FONTS WHERE THE WIDTH OF THE UPPERCASE LETTER"O" IS 60 PERCENT CONDITIONS. NEITHER PARTY SHALL HAVE ANY
<br /> SECTION 11B-502. WHERE PARKING SPACES ARE MARKED WITH LINES, WIDTH COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE MINIMUM AND 110 PERCENT MAXIMUM OF THE HEIGHT OF THE UPPERCASE OBLIGATION NOR LIABILITY TO THE OTHER (EXCEPT
<br /> MEASUREMENTS OF PARKING SPACES AND ACCESS AISLES SHALL BE MADE REFLECTING SURFACE 35 INCHES (889 MM) MAXIMUM ABOVE THE FINISH FLOOR LETTER"I". STATED ABOVE)UNTIL A WRITTEN AGREEMENT IS
<br /> FROM THE CENTERLINE OF THE MARKINGS. OR GROUND.
<br /> FULLY EXECUTED BY BOTH PARTIES.
<br /> 11B-703.2.5 CHARACTER HEIGHT. CHARACTER HEIGHT MEASURED VERTICALLY
<br /> 11B-502.2 VEHICLE SPACES. CAR AND VAN PARKING SPACES SHALL BE 216 INCHES 11B-603.5 ACCESSORIES.WHERE TOWEL OR SANITARY NAPKIN DISPENSERS, FROM THE BASELINE OF THE CHARACTER SHALL BE 5/8 INCH (15.9 MM) MINIMUM
<br /> (5486 MM) LONG MINIMUM. CAR PARKING SPACES SHALL BE 108 INCHES (2743 MM) WASTE RECEPTACLES, OR OTHER ACCESSORIES ARE PROVIDED IN TOILET AND 2 INCHES (51 MM) MAXIMUM BASED ON THE HEIGHT OF THE UPPERCASE ARCHITECT OF RECORD
<br /> WIDE MINIMUM AND VAN PARKING SPACES SHALL BE 144 INCHES(3658 MM)WIDE FACILITIES, AT LEAST ONE OF EACH TYPE SHALL BE LOCATED ON AN LETTER"I". o -
<br /> ACCESSIBLE ROUTE. ALL OPERABLE PARTS, INCLUDING COIN SLOTS, SHALL BE 11B-703.2.6 STROKE THICKNESS. STROKE THICKNESS OF THE UPPERCASE " 2
<br /> MINIMUM, SHALL BE MARKED TO DEFINE THE WIDTH, AND SHALL HAVE AN ��
<br /> ADJACENT ACCESS AISLE COMPLYING WITH SECTION I IB-502.3. 40 INCHES (1016 MM) MAXIMUM ABOVE THE FINISH FLOOR. LETTER"I" SHALL BE 15 PERCENT MAXIMUM OF THE HEIGHT OF THE CHARACTER. Cz
<br /> > o
<br /> � U
<br /> L 11B-502.3 ACCESS AISLE. ACCESS AISLES SERVING PARKING SPACES SHALL 11B-703.2.7 CHARACTER SPACING. CHARACTER SPACING SHALL BE MEASURED U
<br /> COMPLY WITH SECTION 11B-502.3. ACCESS AISLES SHALL ADJOIN AN ACCESSIBLE WATER CLOSETS BETWEEN THE TWO CLOSEST POINTS OF ADJACENT RAISED CHARACTERS
<br /> j ROUTE. TWO PARKING SPACES SHALL BE PERMITTED TO SHARE A COMMON WITHIN A MESSAGE, EXCLUDING WORD SPACES. WHERE CHARACTERS HAVE
<br /> O ACCESS AISLE. 1113-604 WATER CLOSETS RECTANGULAR CROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISED mcg arch i t e c u r e
<br /> 0 CHARACTERS SHALL BE 1/8 INCH (3.2 MM) MINIMUM AND 4 TIMES THE RAISED 15635 Alton Parkway, Suite 100, Irvine, CA 92618
<br /> 06 11B-502.3.2 LENGTH. ACCESS AISLES SHALL EXTEND THE FULL REQUIRED LENGTH 11B-604.2 LOCATION. THE WATER CLOSET SHALL BE POSITIONED WITH A WALL CHARACTER STROKE WIDTH MAXIMUM. WHERE CHARACTERS HAVE OTHER P:949.553.1117 F: 949.474.7056
<br /> T OF THE PARKING SPACES THEY SERVE. OR PARTITION TO THE REAR AND TO ONE SIDE. THE CENTERLINE OF THE WATER CROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISED CHARACTERS SHALL
<br /> CLOSET SHALL BE 17 INCHES (432 MM) MINIMUM TO 18 INCHES (457 MM) BE 1/16 INCH (1.6 MM) MINIMUM AND 4 TIMES THE RAISED CHARACTER STROKE
<br /> 1113-502.3.3 MARKING.ACCESS AISLES SHALL BE MARKED WITH A BLUE PAINTED MAXIMUM FROM THE SIDE WALL OR PARTITION, EXCEPT THAT THE WATER WIDTH MAXIMUM AT THE BASE OF THE CROSS SECTIONS, AND 1/8 INCH (3.2 MM) ARCHITECT STAMP
<br /> BORDERLINE AROUND THEIR PERIMETER. THE AREA WITHIN THE BLUE CLOSET SHALL BE 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) MINIMUM AND 4 TIMES THE RAISED CHARACTER STROKE WIDTH MAXIMUM AT THE SED ARc
<br /> MAXIMUM FROM THE SIDE WALL OR PARTITION IN THE AMBULATORY ACCESSIBLE TOP OF THE CROSS SECTIONS. CHARACTERS SHALL BE SEPARATED FROM ti
<br /> T_
<br /> BORDERLINES SHALL BE MARKED WITH HATCHED LINES A MAXIMUM OF 36 INCHES OE WIN
<br /> (914 MM)ON CENTER IN A COLOR CONTRASTING WITH THAT OF THE AISLE TOILET COMPARTMENT SPECIFIED IN SECTION 11B-604.8.2. WATER CLOSETS RAISED BORDERS AND DECORATIVE ELEMENTS 3/8 INCH (9.5 MM) MINIMUM.
<br /> 00' SHALL BE ARRANGED FOR ALEFT-HAND OR RIGHT-HAND APPROACH.
<br /> SURFACE, PREFERABLY BLUE OR WHITE. THE WORDS "NO PARKING" SHALL BE
<br /> pXp PAINTED ON THE SURFACE WITHIN EACH ACCESS AISLE IN WHITE LETTERS A 1113-703.2.8 LINE SPACING. SPACING BETWEEN THE BASELINES OF SEPARATE _ 7839
<br /> (� MINIMUM OF 12 INCHES CE MM) IN HEIGHT AND LOCATED TO T VISIBLE FROM 11B-604.3 CLEARANCE. CLEARANCES AROUND WATER CLOSETS AND IN TOILET LINES OF RAISED CHARACTERS WITHIN A MESSAGE SHALL BE 135 PERCENT 9/
<br /> THE ADJACENT VEHICULAR WAY. ACCESS AISLE MARKINGS MAY EXTEND BEYOND
<br /> COMPARTMENTS SHALL COMPLY WITH SECTION 11B-604.3. MINIMUM AND 170 PERCENT MAXIMUM OF THE RAISED CHARACTER HEIGHT. 1
<br /> 00 THE MINIMUM REQUIRED LENGTH.
<br /> N 11B-604.3.1 SIZE. CLEARANCE AROUND A WATER CLOSET SHALL BE 60 INCHES 11B-703.4 INSTALLATION HEIGHT AND LOCATION. SIGNS WITH TACTILE
<br /> N 1113-502.3.4 LOCATION. ACCESS AISLES SHALL NOT OVERLAP THE VEHICULAR (1524 MM) MINIMUM MEASURED PERPENDICULAR FROM THE SIDE WALL AND 56 CHARACTERS SHALL COMPLY WITH SECTION IIB-703.4. F CALIF()
<br /> WAY. ACCESS AISLES SHALL BE PERMITTED TO BE PLACED ON EITHER SIDE OF INCHES (1422 MM) MINIMUM MEASURED PERPENDICULAR FROM THE REAR WALL.
<br /> THE PARKING SPACE EXCEPT FOR VAN PARKING SPACES WHICH SHALL HAVE A MINIMUM 60 INCHES (1524 MM) WIDE AND 48 INCHES (1219 MM) DEEP 11B-703.4.1 HEIGHT ABOVE FINISH FLOOR OR GROUND. TACTILE CHARACTERS
<br /> IL ACCESS AISLES LOCATED ON THE PASSENGER SIDE OF THE PARKING SPACES. MANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET. ON SIGNS SHALL BE LOCATED 48 INCHES (1219 MM) MINIMUM ABOVE THE FINISH
<br /> FLOOR OR GROUND SURFACE, MEASURED FROM THE BASELINE OF THE LOWEST
<br /> N 11B-502.4 FLOOR OR GROUND SURFACES. PARKING SPACES AND ACCESS AISLES 11B-604.3.2 OVERLAP. THE REQUIRED CLEARANCE AROUND THE WATER CLOSET BRAILLE CELLS AND 60 INCHES (1524 MM) MAXIMUM ABOVE THE FINISH FLOOR OR 39"
<br /> SERVING THEM SHALL COMPLY WITH SECTION IIB-302. ACCESS AISLES SHALL BE SHALL BE PERMITTED TO OVERLAP THE WATER CLOSET, ASSOCIATED GRAB GROUND SURFACE, MEASURED FROM THE BASELINE OF THE HIGHEST LINE OF
<br /> AT THE SAME LEVEL AS THE PARKING SPACES THEY SERVE. CHANGES IN LEVEL BARS, DISPENSERS, SANITARY NAPKIN DISPOSAL UNITS, COAT HOOKS, SHELVES, RAISED CHARACTERS. „
<br /> ARE NOT PERMITTED.
<br /> ACCESSIBLE ROUTES, CLEAR FLOOR SPACE AND CLEARANCES REQUIRED AT 36
<br /> U OTHER FIXTURES, AND THE TURNING SPACE. NO OTHER FIXTURES OR
<br /> 11B-703.4.2 LOCATION.WHERE A TACTILE SIGN IS PROVIDED AT A DOOR, THE 6" 48" 00
<br /> 11B-502.5 VERTICAL CLEARANCE. PARKING SPACES, ACCESS AISLES AND OBSTRUCTIONS SHALL BE LOCATED WITHIN THE REQUIRED WATER CLOSET SIGN SHALL BE LOCATED ALONGSIDE THE DOOR AT THE LATCH SIDE. WHERE A 24" 12"
<br /> Ofi
<br /> CLEARANCE. TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGN
<br /> VEHICULAR ROUTES SERVING THEM SHALL PROVIDE A VERTICAL CLEARANCE OF
<br /> Q 98 INCHES (2489 MM) MINIMUM. SHALL BE LOCATED ON THE INACTIVE LEAF. WHERE A TACTILE SIGN IS PROVIDED
<br /> NAT SEATS. THE SEAT HEIGHT OF A WATER CLOSET ABOVE THE FINISH AT DOUBLE DOORS WITH TWO ACTIVE LEAFS, THE SIGN SHALL BE LOCATED TO o
<br /> p THE RIGHT OF THE RIGHT HAND DOOR. WHERE THERE IS NO WALL SPACE AT THE 1113-502.6 IDENTIFICATION. PARKING SPACE IDENTIFICATION SIGNS SHALL INCLUDE FLOOR SHALL BE 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) I _
<br /> MAXIMUM MEASURED TO THE TOP OF THE SEAT. SEATS SHALL NOT BE SPRUNG LATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT SIDE OF DOUBLE DOORS,
<br /> THE INTERNATIONAL SYMBOL OF ACCESSIBILITY COMPLYING WITH SECTION
<br /> o TO RETURN TO A LIFTED POSITION. SEATS SHALL BE 2 INCHES (51 MM) HIGH SIGNS SHALL BE LOCATED ON THE NEAREST ADJACENT WALL. SIGNS Cl) - "' L
<br /> 11B-703.7.2.1. SIGNS IDENTIFYING VAN PARKING SPACES SHALL CONTAIN Cl) ch ^,
<br /> 75 ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGN WITH THE DESIGNATION "VAN MAXIMUM. CONTAINING TACTILE CHARACTERS SHALL BE LOCATED SO THAT A CLEAR M0) W
<br /> FLOOR SPACE OF 18 INCHES 457 MM MINIMUM BY 18 INCHES 4 0
<br /> `-' ACCESSIBLE." SIGNS SHALL BE 60 INCHES (1524 MM) MINIMUM ABOVE THE FINISH ( ) ( 57 MM) MINIMUM, � � > � �
<br /> Q 11B-604.5 GRAB BARS. GRAB BARS FOR WATER CLOSETS SHALL COMPLY WITH CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OF
<br /> FLOOR OR GROUND SURFACE MEASURED TO THE BOTTOM OF THE SIGN.
<br /> U SECTION 11B-609. GRAB BARS SHALL BE PROVIDED ON THE SIDE WALL CLOSEST ANY DOOR SWING BETWEEN THE CLOSED POSITION AND 45 DEGREE OPEN O
<br /> _
<br /> TO THE WATER CLOSET AND ON THE REAR WALL. WHERE SEPARATE GRAB BARS POSITION. WHERE PERMANENT IDENTIFICATION SIGNAGE IS PROVIDED FOR 18" 39 1/2" 5 1/4" U Lp
<br /> co
<br /> v 1113-502.6.1 FINISH AND SIZE. PARKING IDENTIFICATION SIGNS SHALL BE ARE REQUIRED ON ADJACENT WALLS ATA COMMON MOUNTING HEIGHT, AN L- ROOMS AND SPACES THEY SHALL BE LOCATED ON THE APPROACH SIDE OF THE LLI U LU
<br /> ca REFLECTORIZED WITH A MINIMUM AREA OF 70 SQUARE INCHES (45161 MM2). 0� U)
<br /> SHAPED GRAB BAR MEETING THE DIMENSIONAL REQUIREMENTS OF SECTIONS DOOR AS ONE ENTERS THE ROOM OR SPACE. SIGNS THAT IDENTIFY EXITS SHALL TOILET TOILET 0 0 4-
<br /> 11B-604.5.1 AND 11 B-604.5.2 SHALL BE PERMITTED. BE LOCATED ON THE APPROACH SIDE OF THE DOOR AS ONE EXITS THE ROOM FRONT ELEVATION SIDE ELEVATION Q "�+ 0 Q
<br /> L 1113-502.6.2 MINIMUM FINE. ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGN z Q > O
<br /> BELOW THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL STATE "MINIMUM OR SPACE. 0 U
<br /> 11B-604.5.1 SIDE WALL. THE SIDE WALL GRAB BAR SHALL BE 42 INCHES (1067 MM) I- > I--- - >1
<br /> _O W FINE $250." LONG MINIMUM, LOCATED 12 INCHES (305 MM) MAXIMUM FROM THE REAR WALL U (.� U U
<br /> U U
<br /> 061113-502.6.3 LOCATION.A PARKING SPACE IDENTIFICATION SIGN SHALL BE VISIBLE AND EXTENDING 54 INCHES (1372 MM) MINIMUM FROM THE REAR WALL WITH THE =3FRONT END POSITIONED 24 INCHES (610 MM) MINIMUM IN FRONT OF THE WATER O O Ca
<br /> v FROM EACH PARKING SPACE. SIGNS SHALL BE PERMANENTLY POSTED EITHER CLOSET.
<br /> (� L
<br /> IMMEDIATELY ADJACENT TO THE PARKING SPACE OR WITHIN THE PROJECTED D_ D_ Ln U
<br /> PARKING SPACE WIDTH AT THE HEAD END OF THE PARKING SPACE. SIGNS MAY~I 11B-604.5.2 REAR WALL. THE REAR WALL GRAB BAR SHALL BE 36 INCHES (914 18 1/4" ��
<br /> MM ALSO BE PERMANENTLY POSTED ON A WALL AT THE INTERIOR END OF THE ) STORE #: 8981
<br /> LONG MINIMUM AND EXTEND FROM THE CENTERLINE OF THE WATER �
<br /> op PARKING SPACE. CLOSET 12 INCHES (305 MM) MINIMUM ON ONE SIDE AND 24 INCHES (610 MM)
<br /> 0000 MINIMUM ON THE OTHER SIDE. PROJECT #: 23870-070
<br /> 11B-502.6.4 MARKING. EACH ACCESSIBLE CAR AND VAN SPACE SHALL HAVE
<br /> SURFACE IDENTIFICATION COMPLYING WITH EITHER SECTION 11B-502.6.4.1 OR - CASEWORK CONCEPT:
<br /> m 11B-604.6 FLUSH CONTROLS. FLUSH CONTROLS SHALL BE HAND OPERATED OR co
<br /> (!)I 1113-502.6.4.2. AUTOMATIC. HAND OPERATED FLUSH CONTROLS SHALL COMPLY WITH SECTIONISSUE DATE: 02-23-2021
<br /> IIB-309 EXCEPT THEY SHALL BE LOCATED 44 INCHES (1118 MM) MAXIMUM ABOVE i,- co co PROGRAM MANAGER: <DESIGN MANAGER>
<br /> N `V
<br /> 11B-502.6.4.1 THE PARKING SPACE SHALL BE MARKED WITH AN INTERNATIONAL THE FLOOR. FLUSH CONTROLS SHALL BE LOCATED ON THE OPEN SIDE OF THE
<br /> p SYMBOL OF ACCESSIBILITY COMPLYING WITH SECTION 1113-703.7.2.1 IN WHITE ON WATER CLOSET EXCEPT IN AMBULATORY ACCESSIBLE COMPARTMENTS STORE DESIGNER: JESSICA RAMOS
<br /> N A BLUE BACKGROUND A MINIMUM 36 INCHES WIDE BY 36 INCHES HIGH (914 MM X COMPLYING WITH SECTION 11B-604.8.2. ` LEED�AP: N/A
<br /> U) 914 MM). THE CENTERLINE OF THE INTERNATIONAL SYMBOL OF ACCESSIBILITY CHECKED BY: <CHECKED BY>
<br /> 0 SHALL BE A MAXIMUM OF 6 INCHES (152 MM) FROM THE CENTERLINE OF THE HAND SINK HAND SINK
<br /> PARKING SPACE, ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACE
<br /> 11B-604.7 DISPENSERS. TOILET PAPER DISPENSERS SHALL COMPLY WITH SIDE ELEVATION FRONT ELEVATION COAT MCG PROJECT#:
<br /> SECTION IIB-309.4 AND SHALL BE 7 INCHES (178 MM) MINIMUM AND 9 INCHES (229 HOOK ELEVATION
<br /> AND ITS LOWER CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THE MM) MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO THE MCG PROJ. MANAGER:
<br /> PARKING SPACE LENGTH. CENTERLINE OF THE DISPENSER. THE OUTLET OF THE DISPENSER SHALL BE MCG PROJ. SPECIALIST:
<br /> O 1113-502.6.4.2 THE PARKING SPACE SHALL BE OUTLINED OR PAINTED BLUE AND BELOW THE GRAB BAR, 19 INCHES (483 MM) MINIMUM ABOVE THE FINISH FLOOR 4„
<br /> SHALL BE MARKED WITH AN INTERNATIONAL SYMBOL OF ACCESSIBILITY AND SHALL NOT BE LOCATED BEHIND GRAB BARS. DISPENSERS SHALL NOT BE Revision Schedule
<br /> COMPLYING WITH SECTION 11 B-703.7.2.1 A MINIMUM 36 INCHES WIDE BY 36 INCHES OF A TYPE THAT CONTROLS DELIVERY OR THAT DOES NOT ALLOW CONTINUOUS
<br /> C) PAPER FLOW. ® Rev Date B Description
<br /> N HIGH (914 MM X 914 MM) IN WHITE OR A SUITABLE CONTRASTING COLOR. THE O Y p
<br /> N CENTERLINE OF THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL BE A
<br /> MAXIMUM OF 6 INCHES (152 MM) FROM THE CENTERLINE OF THE PARKING SPACE, LAVATORIES /
<br /> 0
<br /> z ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACE AND ITS LOWER -
<br /> CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THE PARKING SPACE. IIB-606 LAVATORIES AND SINKS
<br /> 11B-502.8 ADDITIONAL SIGNAGE. AN ADDITIONAL SIGN SHALL BE POSTED EITHER- 11B-606.2 CLEAR FLOOR SPACE.A CLEAR FLOOR SPACE COMPLYING WITH m M
<br /> M M
<br /> 75; 1) IN A CONSPICUOUS PLACE AT EACH ENTRANCE TO AN OFF-STREET PARKING SECTION I IB-305, POSITIONED FOR A FORWARD APPROACH, AND KNEE AND 00 00
<br /> IZ FACILITY OR 2) IMMEDIATELY ADJACENT TO ON-SITE ACCESSIBLE PARKING AND TOE CLEARANCE COMPLYING WITH SECTION I IB-306 SHALL BE PROVIDED. N N SHEET TITLE:+�+ �+
<br /> 00 VISIBLE FROM EACH PARKING SPACE. ACCESSIBILITY NOTES
<br /> 11B-606.3 HEIGHT. LAVATORIES AND SINKS SHALL BE INSTALLED WITH THE
<br /> N 11B-502.8.1 SIZE. THE ADDITIONAL SIGN SHALL NOT BE LESS THAN 17 INCHES (432 FRONT OF THE HIGHER OF THE RIM OR COUNTER SURFACE 34 INCHES (864 DIAPER CHANGING DIAPER CHANGING PAPER HAND TOWEL
<br /> j MM)WIDE BY 22 INCHES (559 MM) HIGH. MM) MAXIMUM ABOVE THE FINISH FLOOR OR GROUND. STATION SIDE ELEVATION STATION FRONT ELEVATION DISPENSER FRONT ELEVATION SCALE:AS SHOWN
<br /> 11B-606.4 FAUCETS. CONTROLS FOR FAUCETS SHALL COMPLY WITH SECTION
<br /> 11B-502.8.2 LETTERING. THE ADDITIONAL SIGN SHALL CLEARLY STATE IN LETTERS 11B-309. HAND-OPERATED METERING FAUCETS SHALL REMAIN OPEN FOR 10
<br /> N WITH A MINIMUM HEIGHT OF 1 INCH (25 MM)THE FOLLOWING: SECONDS MINIMUM. MOUNTING HEIGHTS FOR RESTROOM ACCESSORIES SHEET NUMBER:
<br /> N
<br /> Scale: 3/8" = V-0"
<br /> G005
<br />
|