Laserfiche WebLink
METAL TEA SHELF MOUNTING <br />Scale 6" = 1'-0" <br />01POS CABINET W/ CUP DISPENSER <br />Scale 1 1/2" = 1'-0" <br />04 <br />DIEWALL ASSEMBLY @ BAR <br />Scale 1 1/2" = 1'-0" <br />08 <br />ESPRESSO PUMP MOUNT @ CABINET <br />Scale 1 1/2" = 1'-0" <br />09U/C FRIDGE STOP INSTALLATION <br />Scale 1 1/2" = 1'-0" <br />12 FINISH APP. (MAD 100-H) PLANK <br />Scale 3/4" = 1'-0" <br />06 FINISH PANEL/ ESP SHROUD DETAIL <br />Scale 6" = 1'-0" <br />03 <br />DIRECTION OF GRAIN, TYP. ALL PLANKS <br />TONGUE-IN-GROOVE PLANKS <br />MIN. 12" END PIECES <br />METAL TRIM @ CORNER AND <br />BOTTOM <br /> A <br />-HEIGHT VARIESB. ELEVATION <br />2'-0'' TO 8'-0'' LENGTH PLANKS RANDOMLY PLACED <br />RANDOM PLANK LAYOUT WITH NO VISIBLE <br />CONTINUOUS VERTICAL SEAMS UNLESS <br />OTHERWISE DETAILED <br />A. ENLARGED SECTION PROFILE <br />(N.T.S.)INTERIOR SIDECUSTOMER SIDEINTERIOR SIDE TO <br />BE SECURED TO <br />SUBSTRATE/ <br />STRUCTURE PER <br />DETAILS <br />MICROBEVEL PROFILE AT JOINT <br />(TYP.) <br />TONGUE-IN-GROOVE PLANKS <br />SECURED TO SUBSTRATE / <br />STRUCTURE AND MECHANICALLY <br />FASTENED AS REQUIRED <br />1/4" BACKER (TYP.) ACTUAL <br />SIZE/MATERIAL SPEC. <br />DETERMINED BY CASEWORK <br />SUPPLIER. <br />13/16'' <br />9/16'' <br />HARDWOOD WEAR LAYER <br />PLYWOOD5'' (TYP.)COVE DETAIL ON THIS SIDE ONLY <br />'U' SHAPED ALUMINUM GLAZING <br />SEAT SECURE TO BLOCKING <br />BELOW <br />BLOCKING <br />MIN. 1/16" GAP AT GLASS FILLED <br />WITH CLEAR SILICONE BOTH <br />SIDES, TYP. <br />1 1/2"6"4"ESPRESSO CAP <br />METAL ANGLE, TYP. <br />COUNTERTOP SUBSTRATE <br />ALUM. Z-CLIPS, TYP. <br />FINISH PANEL <br />DIEWALL <br />CORIAN COUNTERTOP <br />VARIES <br />NOTE: <br />ALL COMPONENTS FURNISHED BY <br />OTHERS AND INSTALLED BY GC, <br />U.O.N.1 3/4"4" <br />TYP.1/2"34" MAX. AFFCORIAN SHROUD <br />3/8" TEMPERED GLASS. VERIFY <br />MIN. GLASS HEIGHT WITH LOCAL <br />CODES <br />GREENBOARD (TYP.) <br />WALL FINISH AS SCHEDULED <br />STEEL PLATE BY STARBUCKS <br />VENDOR AT BACK OF SHELF <br />METAL SHELF UNIT BY <br />STARBUCKS VENDOR <br />2X10 BLOCKING CENTERED ON <br />SHELF SURFACE MOUNTING <br />HEIGHT. SECURE TO EACH NAILER <br />USING (3) # 10 3" WOOD SCREWS <br />@ 4" (100 MM) O.C. <br />2X2 NAILERS, 14" (355 MM) LONG <br />SECURED TO WALL STUDS USING <br />(4) #10 3" WOOD SCREWS AT 4" <br />(100 MM) O.C. PER NAILER <br />(11 TOTAL) #10 2 1/2" WOOD <br />SCREWS MOUNTED TO BLOCKING <br />THRU PRE-DRILLED HOLES IN <br />PLATE, TYP. <br />WALL STUDSHELF SURFACE AT60" (1525 MM) A.F.F.CUSTOMER <br />SIDE <br />ADJUSTABLE SHELF <br />MELAMINE UNDERSIDE OF <br />COUNTERTOP <br />BASE CABINET <br />HOLE INSIDE FOR ELEC. SUPPLY <br />P-LAM DRAWER FRONT ON 3/4" <br />SUBSTRATE <br />BULLNOSE SANITARY 3/8" MIN <br />COVED TILE BASE <br />PARTNER SIDE <br />POS BANK <br />DIEWALL <br />3'-4" <br />REMOVABLE FINISH PANEL W/ <br />ELECTRICAL CHASE BEHIND <br />GROMMET HOLE FOR COFFEE <br />SHUTTLE CORD <br />5" <br />I520 <br />03 <br />I520 <br />01 <br />NOTE: <br />ALL COMPONENTS FURNISHED BY <br />OTHERS AND INSTALLED BY GC, <br />U.O.N. <br />BARISTA BAR DIE WALL <br />SEAL SOLID SURFACE STEAL <br />SIDESLASH TO TOP CAP <br />CORIAN COUNTERTOP <br />GROMMET HOLE IN SS <br />COUNTERTOP <br />4" X 4" ELECTRICAL J-BOXES <br />MOUNTED TO WALL W/ <br />INTERCONNECTING CONDUIT <br />CASEWORK BASE <br />BULLNOSE SANITARY 3/8" MIN <br />COVED TILE BASE <br />AX.X <br />0 <br />CW SUPPLY. ALL PLUMBING LINES <br />TO BE MOUNTED 1" (NOMINAL) <br />FROM WALL FOR CLEANING <br />NOTE: <br />ALL COMPONENTS FURNISHED BY <br />OTHERS AND INSTALLED BY GC, <br />U.O.N. <br />REMOVABLE CABINET BACK <br />PANEL <br />FRP INTERIOR SURFACE <br />ABS 2" WASTE LINE, 1/4" PER <br />FEET FALL <br />AX.X <br />0 <br />VARIES1"1"1'-5"2'-2"BARISTA BAR DIE WALL <br />SEAL SOLID SURFACE STEAL <br />SIDESLASH TO TOP CAP <br />CORIAN COUNTERTOP <br />GROMMET HOLE IN SS <br />COUNTERTOP <br />4" X 4" ELECTRICAL J-BOXES <br />MOUNTED TO WALL W/ <br />INTERCONNECTING CONDUIT <br />CASEWORK BASE <br />BULLNOSE SANITARY 3/8" MIN <br />COVED TILE BASE <br />I520 <br />03 <br />CW SUPPLY. ALL PLUMBING LINES <br />TO BE MOUNTED 1" (NOMINAL) <br />FROM WALL FOR CLEANING <br />NOTE: <br />ALL COMPONENTS FURNISHED BY <br />OTHERS AND INSTALLED BY GC, <br />U.O.N. <br />REMOVABLE CABINET BACK <br />PANEL <br />FRP INTERIOR SURFACE <br />ABS 2" WASTE LINE, 1/4" PER <br />FEET FALL <br />I502 <br />03 <br />VARIES1"1"1'-5"2'-2"6"NOTES: <br />1.LOCATE PUMP WITHIN CORD LENGTH LIMIT. ORIENT WITH PUMP HEAD LEFT, RIGHT AND AT BOTTOM. LOOSEN PUMP <br />HEAD CLAMP, ROTATE AND RE-TIGHTEN AS REQUIRED PER ORIENTATION TO PROVIDE FRONT ACCESS TO FLOW. <br />ADJUSTMENT WITHIN CORD LENGTH LIMIT. <br />2.USE LOCKTITE ON ISOLATOR THREADS. DO NOT OVER TIGHTEN. <br />3.LOOSEN PUMP HEAD CLAMP, ROTATE AND RE-TIGHTEN AS REQUIRED FOR PUMP ORIENTATION. <br />4.BACKER BOARD ASSEMBLY INCLUDES: <br />(1) BACKER BOARD <br />(4) TENETS, 1/4-20 VENDOR MOUNTED <br />(8) WOOD SCREWS #8 1-1/4" (32MM) <br />(4) NEOPRENE ISLOATORS, KARMAN RUBBER, K84-60 NEOPRENE <br />(4) LOCK NUTS, 1/4-20 NYLON <br />(4) WASHERS, 1/4" (7MM) FLAT <br />EXTERIOR FACE OF CABINET <br />FINISHED FLOOR <br />PUMP ATTACHED TO BACKER <br />BOARD WITH ASSEMBLY <br />COMPONENT <br />SEE NOTES ABOVE FOR <br />ASSEMBLY ITEMS <br />BASE CABINET <br />SECOND PUMP STACKED ABOVE <br />UNIT BELOW <br />10"X10" (250MMX250MM) BACKER <br />BOARD. ATTACH TO DIE WALL <br />WITH SILICONE ADHESIVE AND <br />WOOD SCREWS. SILICONE <br />PERIMETER <br />DO NOT BLOCK GROMMET <br />OPENING CUT ANGLE AS <br />REQUIRED TO MAINTAIN MIN. 1/2" <br />(13MM) CLEAR AROUND OPENING <br />MECHANICALLY FASTEN <br />COUNTER-SUNK CORROSION <br />RESISTANT FASTENERS AT <br />6"(150MM) O.C. WITH 3/4" (19MM) <br />EMBEDMENT. <br />MECHANICALLY FASTEN ANGLE <br />TO COUNTERTOP SUBSTRATE OR <br />EPOXY FASTEN IT TO <br />COUNTERTOP <br />1 1/2" X 1 1/2" (38MM X 38MM) <br />CORROSION RESISTANT STEEL <br />ANGLE <br />1/2" (13MM) PREFERRED OFFSET <br />DISTANCE FROM EDGE OF <br />COUNTERTOP <br />COUNTERTOP DEPTH MAY VARY <br />STEEL ANGLE CENTERED ON <br />REFRIGERATOR <br />EQ.2'-5" <br />A. PLAN VIEW <br />NOTES: <br />1. 24" (610MM) 1 1/2" X 1 1/2" <br />(38MM X 38MM) STEEL ANGLE TO <br />BE USED WITH SINGLE DOOR <br />REFRIGERATORS <br />2. 48" (1220MM) 1 1/2" X 1 1/2" <br />(38MM X 38MM) STEEL ANGLE TO <br />BE USED WITH DOUBLE DOOR <br />REFRIGERATORS <br />COUNTERTOP ABOVE <br />3/4"UNDERCOUNTER REFRIGERATOR <br />B. SECTION VIEW <br />UNDERCOUNTER REFRIGERATOREQ.- <br />B <br />- <br />B <br />SHEET NUMBER: <br />SHEET TITLE: <br />SCALE: AS SHOWN <br />STORE #: <br />PROJECT #:PROJECT NAME:PROJECT ADDRESS:C 2020 STARBUCKS COFFEE COMPANY <br />R <br />ISSUE DATE: <br />2401 UTAH AVENUE SOUTH <br />SEATTLE, WASHINGTON 98134 <br />(206) 318-1575 <br />THESE DRAWINGS AND THE PROJECT MANUAL <br />ARE CONFIDENTIAL AND SHALL REMAIN THE <br />SOLE PROPERTY OF STARBUCKS <br />CORPORATION, WHICH IS THE OWNER OF THE <br />COPYRIGHT IN THIS WORK. THEY SHALL NOT <br />BE REPRODUCED (IN WHOLE OR IN PART), <br />SHARED WITH THIRD PARTIES OR USED IN ANY <br />MANNER ON OTHER PROJECTS OR <br />EXTENSIONS TO THIS PROJECT WITHOUT THE <br />PRIOR WRITTEN CONSENT OF STARBUCKS <br />CORPORATION. THESE DRAWINGS AND <br />SPECIFICATIONS ARE INTENDED TO EXPRESS <br />DESIGN INTENT FOR A PROTOTYPICAL <br />STARBUCKS STORE (WHICH IS SUBJECT TO <br />CHANGE AT ANYTIME) AND DO NOT REFLECT <br />ACTUAL SITE CONDITIONS. NEITHER PARTY <br />SHALL HAVE ANY OBLIGATION NOR LIABILITY TO <br />THE OTHER (EXCEPT STATED ABOVE) UNTIL A <br />WRITTEN AGREEMENT IS FULLY EXECUTED BY <br />BOTH PARTIES. <br />STARBUCKS TEMPLATE VERSION: i2020-07-27 <br />R <br />SR. DESIGN MANAGER: <br />DESIGN MANAGER: <br />CHECKED BY: <br />R <br />I502 <br />23871-068 <br />02-05-2021HIGHWAY 99 & WATERLOO4426 EAST WATERLOO ROADSTOCKTON, CA 95215COUNTRY OF SAN JOAQUIN7957 <br />JESSICA RAMOS <br />JESSICA RAMOS <br />JOSE LAROCCA <br />CASEWORK DETAILS <br />Revision Schedule <br />Rev Date By Description <br />01/28/21 JGR FINAL REVIEW SET <br />02/05/21 JGR PERMIT SET <br />1 <br />2 <br />3