WORK PLANS - Laserfiche WebLink

Home Browse Search

SECTION 09260 - GYPSUM WALLBOARD ASSEMBLIES 2.2 ACOUSTIC CEILING UNITS PART 2 - PRODUCTS 4. Non-Ferrous Metal A. ACOUSTICAL CEILING PANEL ACP - TYPE ACP-1 a. Gloss - Alkyd / 100% Acrylic 1. For assemblies with fire resistance ratings, provide materials and construction identical to those tested in assembly (ACP) [ ] 2.01 MANUFACTURERS: Pretreatment Supreme Chemical, Metal Clean and Etch ME 01 indicated by ASTM E 119 . 1. NAME: ECOPHON FOCUS F P ( ) 2. For assemblies with STC ratings, provide materials and construction identical to those tested in assembly indicated by 2. PHYSICAL CHARACTERISTICS A. Manufacturer's catalog names and number of paint types in this Section herein are based on products manufactured First Coat DE ULTRA-GRIP Premium Primer/Sealer (UGPR00) ASTM E 90 and ASTM E 413. a. TYPE: XII (PER ASTM E1264) or distributed by the Dunn-Edwards Corporation www.dunnedwards.com and are the basis of design. No substitutions Second Coat ARISTOSHIELD Exterior Gloss Paint (ASHL70) d ll ill be allowed.3. STEEL FRAMING: ASTM C 754, Steel Sheet Components: ASTM C 645, ASTM A 653 G60 hot dip galvanized zinc coating. b. FORM: 2 (PER ASTM E1264) wThird Coat ARISTOSHIELD Exterior Gloss Paint (ASHL70) Architecture / Development Systems: C.Minimum Base Metal Thickness: 0.0312 inch unless noted otherwise. c. PATTERN: G (PER ASTM E1264) CAcceptable Manufacturers B. Substitutions: Dunn-Edwards Paint only A. Interior S Y 4. TIE WIRE: ASTM A 641/A 641M, Class 1 zinc coating, soft temper, 0.0625 inch diameter wire, or double strand of d. SIZE: METRIC ONLY 1. Gypsum Board Soffit / Dining Room Ceiling 1. Dunn-Edwards 14901 Quorum Drive a. Eggshell - Acrylic Co-Polymer 100% Acrylic 0.0475 inch diameter wire. 1) 600 X 600 MM [=23.62"X 23.62"] 2. Sherwin-Williams of equal spec to Dunn-Edwards products specified, where Dunn-Edwards is not available. gg ry y / ry Suite 300 5. WIRE HANGERS: ASTM A 641/A 641M, Class 1 zinc coating, soft temper, 0.162 inch diameter. 2) THICKNESS: 20MM [=3/4"] First Coat SUPREME WALL Premium Primer Dallas Texas 75254 6. CARRYING CHANNELS: Cold rolled, commercial steel sheet with a base metal thickness of 0.0538 inch a minimum 1/2 e. EDGES: REINFORCED, PAINTED AND BEVELED 2.02 MATERIALS: Second Coat EVERSHIELD Paint (EVSH30) Third Coat EVERSHIELD Paint (EVSH30) (972) 84 Fa 239-5 inch wide flange, and in depth indicated. 1) TONGUE AND GROOVE (2 SUPPORTING EDGES) A. Paints: Provide ready-mixed, except field catalyzed coatings. Pigments shall be fully ground maintaining soft paste Fax: (972)239-5054 7. COLD ROLLED CHANNELS: 0.0538 inch bare steel thickness, with minimum 1/2 inch wide flange, 3/4 inch deep. 2) KERFED (2 NON-SUPPORTING EDGES) consistency, capable of being readily and uniformly dispersed to complete homogeneous mixture. Paints shall have 2. Gypsum Board Back Room, Office, Locker Room, Restrooms, 8. Steel Studs and Runners: ASTM C 645, in depth indicated. f. FINISHED SURFACE: AKUTEX FT good flowingand brushing properties and be capable of in or curing free of streaks and sags. a. Gloss - 100% Acrylic 9 P P P drying 9 9 ISSUE RECORD 9. HAT SHAPED, RIGID FURRING CHANNELS: ASTM C 645, 7/8 inch deep. g. FINISHED SURFACE COLOR: WHITE B. Accessory Materials: Linseed oil, shellac, solvents, and other materials not specified but required to achieve required First Coat SUPREME WALL Premium Primer 10. RESILIENT FURRING CHANNELS: 1/2 inch dee members designed to reduce sound transmission, and asymmetrical with h. PANEL BACKING: FIBERGLASS TISSUE finishes shall be of high quality and approved b manufacturer. Second Coat EVERSHIELD Paint EVSH50 DATE DESCRIPTION / P 9 Y g q y PP y ( ) URBAN PROTOTYPE single leg. i. CORE COMPOSITION: HIGH-DENSITY FIBERGLASS C. Colors shall be selected from color chip samples provided by manufacturer of paint system approved for use. Match Third Coat EVERSHIELD Paint (EVSH50) 11. GRID SUSPENSION SYSTEM FOR INTERIOR CEILINGS: ASTM C 645, direct hung system of interlocking main beams and j. RECYCLED CONTENT: 71% approved samples for color, texture and coverage. 3. Gypsum Board Dining Room Areas to receive Wallcovering 7-7-2020 ISSUED FOR PERMIT cross furring members. 1) 1% (PRE-CONSUMER) D. Aromatic Compounds: Paints and coatings shall not contain more than 1.0 percent by weight of total aromatic a. Acrylic Co-Polymer 12. DEEP LEG DEFLECTION TRACK: ASTM C 645 top runner with 2 inch deep flanges. 2) 70% (POST-CONSUMER)' compounds (hydrocarbon compounds containing one or more benzene rings). First Coat VINYLASTIC Premium, Interior Wall Sealer (VNPROO) 13. FIRESTOP TRACK: Top runner manufactured to allow partition heads to expand and contract with movement of the E. Restricted Components: Paints and coatings shall not contain any of the following: Second Coat 325 Draw-Tite Clear Manufactured by Scotch Paint. (Apply wallcovering with Gardner structure while maintaining continuity of fire resistance rated assembly indicated; in thickness not less than indicated for 2.3 ATTACHMENT 1. Acrolein. 13. Ethylbenzene. Gibson 433 Heavy Duty Clay Strippable Wallcovering Adhesive. Wallpaper should be hung studs and in width to accommodate depth of studs. A. COMPONENTS 2. Acrylonitrile. 14. Ethylene Glycol. with laser to ensure palm trees are level throughout the dining area.) 14. FLAT STRAP AND BACKING PLATE: Steel sheet for blocking and bracing in length and width indicated. a. ACOUSTIC CEILING TILE ADHESIVE 3. Antimony. 15. Formaldehyde. 4. Ferrous Metal Doors and Jams 15. GYPSUM WALLBOARD: ASTM C 36, Regular Type: In thickness indicated and with long edges tapered and featured (rounded b. FRANKLIN INTERNATIONAL'S TITEBOND ACOUSTICAL CEILING TILE ADHESIVE 4. Benzene. 16. Hexavalent chromium. a. SCOPE or beveled), Type X: In thickness indicated and with long edges tapered and featured (rounded or beveled). 2. ACCESSORIES 5. Butyl benzyl phthalate. 17. Isophorone. This specification describes a paint system of Axalto Imron Industrial Strength polyurethane primer and 16. SAG RESISTANT GYPSUM WALLBOARD: ASTM C 36, manufactured for improved sag resistance, with Ion edges tapered. a. LEVELING SPLINES 6. Cadmium. 18. Lead. P 9 9 9 P Imron Industrial Strength polyurethane high gloss topcoat. Apply on ceilings and similar interior horizontal surfaces. b. CONNECT SPLINE (#0219) 7. Di (2-ethylhexyl) phthalate. 19. Mercury. b. GENERAL 17. FIRE RESISTIVE TYPE: ASTM C 36, Type X, complying with requirements of fire resistance rated assemblies indicated, and c. CONNECT WALL SPRING SPACER (#0087) 8. Di-n-butyl phthalate. 20. Methyl ethyl ketone. Modifications must be detailed. with long edges tapered and featured (rounded or beveled) for prefilling. 3. EDGE MOLDING 9. Di-n-octyl phthalate. 21. Methyl isobutyl ketone. c. SURFACE PREPARATION 18. GLASS MAT GYPSUM SHEATHING BOARD: ASTM C 1177. a. TYPE:CERTANTEED WT-1 EDGE MOLDING. COLOR: WHITE 10. 1,2-dichlorobenzene. 22. Methylene chloride. 1. Prepare the surface in accordance with SSPC-SP2 Hand Tool Clean or SSPC-SP3 Power Tool Clean. P REVISION RECORD 19. TILE BACKING PANELS: 11. Diethyl phthalate. 23. Naphthalene. 12. Dimethyl phthalate. 24. Toluene (methyl 2. Prior to primer application solvent clean to SSPC-SP1 with T-1021 acetone. A. Glass Mat, Water Resistant Board: ASTM C 1178. PART 3 - EXECUTION Y P ( Y )• d. APPLICATION B. Cementitious Backer Board ANSI A118.9. 25. trichloroethane. 1. Handling, mixing, re-coating, dry times and application methods must be in accordance with the 20. EXTERIOR AND INTERIOR TRIM: ASTM C 1047, hot dip galvanized steel sheet or rolled zinc. 3.1 EXAMINATION 26. Vinyl chloride. manufacturers written instructions. 21. JOINT TAPE: ASTM C 475, Interior Gypum Wallboard: Paper, Glass Mat Gypsum Sheathing Board: 10 by 10 glass mesh, A. ASCERTAIN ACCEPTABILITY OF SUBSTRATES AND BUILDING CONDITIONS UNDER WHICH THE CEILING SYSTEM IS TO BE 2.04 MIXES: 2. On the same day as the surface is cleaned apply the Imron Industrial Strength polyurethane primer at Tile Backing Panels: As recommended by panel manufacturer. INSTALLED. DO NOT PROCEED WITH THE INSTALLATION UNTIL ANY AND ALL UNACCEPTABLE CONDITIONS HAVE BEEN A. Mix, prepare, and store painting and finishing materials in accordance with manufacturer's directions. 3.0 to 5.0 mils dry film thickness. 22. Joint Compound for Interior Gypsum Wallboard compatible with other compounds applied on previous or for successive RECTIFIED. 3. After the prime coat has dried sufficiently for re-coat, depending on film thickness, temperature and coats. 3.2 PREPARATION PART 3-EXECUTION humidity, apply a top coat of Imron Industrial Strength high gloss polyurethane at 2.0 to 3.0 mils dry 23. JOINT COMPOUND FOR TILE BACKING PANELS: Water Resistant Gypsum Backing Board: Use setting type taping and setting A. UNLESS OTHERWISE DIRECTED BY THE REFLECTED CEILING PLAN, MEASURE THE SPACE IN WHICH THE CEILING SYSTEM film thickness. type, sandable topping compounds. IS TO BE INSTALLED AND ESTABLISH A LAYOUT THAT BALANCES BORDER WIDTHS AT OPPOSITE ENDS OF THE CEILING. 3.01 EXAMINATION: 4. Total dry film thickness must be at least 5.0 mils minimum. Maximum dry film thickness is 8.0 mils. 24. Acoustical Sealant for Exposed and Concealed Joints ASTM E 90and ASTM C 834 Nonsag, paintoble, nonstaining, latex B. WHEN POSSIBLE, COORDINATE THE CEILING SYSTEM LAYOUT TO AVOID THE USE OF LESS THAN HALF WIDTH PANELS AT A. Examine surfaces to be painted before beginning painting work. Work of other trades that has been left or installed e. INSPECTION sealant. THE PERIMETER. in a condition not suitable to receive paint, stain other specified finish shall be repaired or corrected by the 25. SOUND ATTENUATION BLANKETS: ASTM C 665, Type I blankets without membrane facing. Comply with mineral fiber applicable trade before painting. Paintingof defective or unsuitable surface implies acceptance of the surfaces. 1. All prepared surfaces can be inspected and approved by an owners representative prior to primer YP g' P y PP P g' P P application and prior to topcoat application and after primer and topcoat application. requirements of fire resistance rated assemblies. 3.3 INSTALLATION B. Beware of a condition known as critical lighting. This condition causes shadows that accentuate even the slightest 26. Non load bearingsteel framing installation. ASTM C 754, and ASTM C 840 requirements for framing installation. A. INSTALL THE CEILING SYSTEM IN ACCORDANCE WITH THE FOLLOWING: surface variations. A 2. Dry film thickness of each coat must be measured as described y ASTM unifoD118rm (ferrous substrates). 9 q 9 pigmented sealer will provide tooth for succeeding decorative coating, but does not equalize 3. The completed system must be inspected visually for skips, holidays and uniform color. Defects shall 27. Gypsum wallboard installation, ASTM C 840 and GA-216. 1. MANUFACTURER'S PRINTED INSTRUCTIONS smoothness or surface texture. Any corrective action to drywall must be done by the drywall contractor prior to be repaired before final acceptance. 28. INSTALLING TRIM ACCESSORIES: For trim with back flanges intended for fasteners, attach to framing with some fasteners a. AVAILABLE ONLINE AT WWW.CERTAINTEED.COM/COMMERCIAL-CEILINGS APPLICABLE LOCAL CODE REQUIREMENTS decorating. used for panels. Otherwise, attach trim according to manufacturer's written instructions. 2. APPLICABLE LOCAL CODE REQUIREMENTS SSPC-Steel Structures Paint Council 29. LEVELS OF GYPSUM BOARD FINISH; Gypsum Association GA-214. 3.02 PROTECTION: NOTICE Level 0: Not used 3.4 INSTALLATION METHOD A. Protect previously installed work and materials, which may be affected by Work of this Section. Availability of products listed in this specification may be affected by local, state, or federal regulatory requirements for Level 1: Wall Spaces above Ceilings. A. TEMPERATURE OF ADHESIVE AND SUBSTRATE MUST BE OVER 50-DEGREES F 1.Protect prefinished surfaces, lawns, shrubbery and adjacent surfaces against paint and damage. architectural coatings. Consult our Dunn-Edwards representative for information on current product availability. Level 2: Fire Riser Room, Electrical Room, and locations to receive wall tile or F.R.P. B. PLACE THE PANEL FACE-DOWN ON A FLAT WORK SURFACE TAKING CARE NOT TO DAMAGE THE FINISHED SURFACE. 2. Furnish sufficient drop cloths, shields, and protective equipment to prevent spray or splatter from fouling g Y P P Y Level 3: Not used. C. SCOOP A QUANTITY OF TITLEBOND ACOUSTICAL CEILING TILE ADHESIVE FROM THE CONTAINER WITH A TROWEL. surfaces not being painted. SECTION 10155 - TOILET COMPARTMENTS Level 4: Dining Room and any locations to receive wall paper. D. SPREAD ADHESIVE - EACH APPLICATION SHOULD BE A MINIMUM OF 5 INCHES X 5 INCHES AND BEGIN APPROXIMATELY 3. Protect surfaces, equipment, and fixtures from damage resulting from use of fixed, movable and hanging 1. Subject to compliance with requirements, provide products by the following: Level 5: All locations where painted gypsum board is to be the final finish. 1.5 INCHES OF THE PANEL EDGE scaffolding, planking, and staging. E. RETURN TO EACH ADHESIVE SPOT AND USE THE TOOTHED END TOF THE TROWEL TO CREATE RIDGES OVER THE B. Provide wet paint signs, barricades, and other devices required to protect newly finished surfaces. Remove temporary A. Laminating Technologies, a CA Division of YTI Enterprises, Inc. SECTION 09310 - CERAMIC TILE ENTIRETY OF EACH ADHESIVE SPOT protective wrappings provided by others for protection of their work after completion of painting operations. 1260 S. State College Pkwy, Anaheim, CA. 92806 1. Furnish extra materials matching, products installed. Package with protective covering for storage and identify with labels F. IMMEDIATELY LIFT PANEL INTO PLACE AND PRESS FIRMLY AGAINST THE SUBSTRATE TAKING CARE TO MOVE THE PANEL Contact: Jair Rochverger Tel 714-632-8696 Fax 714-632-8685; email: laminatingtech®sbcglobal.net PROFESSIONAL SEAL describing contents. Furnish quantity of full size tile and trim units equal to 3 percent of amount installed, for each SLIGHTLY IN A HORIZONTAL DIRECTION TO SET THE ADHESIVE. 3.03 PREPARATION: type, composition, color, pattern, and size. 1. THE HOLD SHOULD BE ALMOST IMMEDIATE A. Perform preparation and cleaning procedures in strict accordance with coating manufacturer's instructions for each 2. Core Material Doors, Panels and Pilasters consists of moisture-resistant honeycomb core with a 5WL Diamondt►Is RC�jr� 2. Waterproof, Crack Suppression Membranes for Thin Set Tile Installations ANSI A118.10 Manufacturer's standard. 2. IF IT IS NOT, RE-EVALUATE THE INSTALLATION APPLICATION AND THE SUBSTRATE. substrate condition. Texture Stainless Steel Finish. �tk 3. PORTLAND CEMENT MORTAR THICKSET INSTALLATION MATERIALS: ANSI A108.1A. B. Concrete and Masonry: Surfaces shall be dry, clean, and free of dirt, efflorescence, encrustation, and other foreign 3. PILASTER SHOES AND SLEEVES (CAPS): Stainless steel, not less than 3 inches high with an integral heel. F 0 4. DRY SET PORTLAND CEMENT MORTAR THIN SET: ANSI A118.1. 3.4 MAINTENANCE matter. Glazed surfaces on concrete shall be roughened or etched to uniform texture. 4. STIRRUP BRACKETS: Stainless Steel supplied with 3 per connection 0 back of wall only. G 5. CHEMICAL RESISTANT, WATER CLEANABLE, TILE SETTING AND GROUTING EPDXY: ANSI A118.3. A. REPLACE ANY AND ALL DAMAGED CEILING SYSTEM COMPONENTS C. Ferrous Metal: Clean oil, grease, and foreign matter with solvent. Surface shall be primed within 3 hours after 5. CONTINUOUS BRACKETS: Stainless Steel 57" High at front of stalls for Privacy from the outside. * I,* 6. WATER CLEANABLE, TILE SETTING EPDXY ADHESIVE: ANSI A118.3. B. CLEAN ANY AND ALL EXPOSED SURFACES IN ACCORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS preparation. 6. TOILET COMPARTMENTS: Floor mounted overhead braced. 7. LATEX ADHESIVE: ANSI A136.1, Type I. D. Sand and scrape metal to remove loose primer and rust. 7. URINAL SCREENS: Wall hung. $E 30 11 8. STANDARD SANDED CEMENT GROUT: ANSI A118.6, color as selected by Architect. E. Non-Ferrous Metal: Chemically or solvent clean and then treat with an etching-type solution if recommended by the I t 8. DOORS: Unless otherwise indicated, 24" wide in swinging doors for standard toilet compartments and 36" wide out swinging 9. SAND PORTLAND CEMENT GROUT: ANSI A108.10, color as selected by Architect. finish manufacturer. Cleaned and retreated Non-Ferrous Metal shall be primed the same day that cleaning has been 10. Elastomeric Sealants One Part, Mildew Resistant Silicone ASTM C 920; Type S; Grade NS; Class 25; Uses NT, G, A, and, performed. doors with a min. wide clear opening for compartments indicated to be accessible to people with disabilities. OF SECTION 09900 - PAINTING P 9. PANELS: Interior Panels ls are to be re-inforced for ADA grab bar placement. as applicable to nonporous joint substrates indicated, 0; formulated with fungicide, intended for in service exposures of F. Wood Surfaces: Remove dust, grit and foreign matter. Sand surfaces and dust clean. Spot coat knots, pitch streaks, 1D-15 �u�v high humidity and extreme temperatures. PARTS 1 - GENERAL and sappy section with pigmented stain sealer when surfaces are to be painted. Fill nail holes, cracks and other 10. DOOR HARDWARE: Cast Stainless Steel with surface mounted latch. Provide units that comply with accessibility requirements of 11. Trowelable Underlayments and Patching Compounds: Latex modified, portland cement based formulation provided or defects after priming and spot prime repairs when fully cured. authorities having jurisdiction at compartments indicated to be accessible to people with disabilities. ADA doors shall have approved by manufacturer of tile setting materials. 1.01 SUMMARY: G. Remove hardware and accessories, machined surfaces, plates, lighting fixtures and similar items in place and double door pulls. 11 12. Remove coatings, curing compounds and other substances that contain soap, wax, oil, or silicone, that are incompatible A. SECTION INCLUDES: PAINTING AND FINISHING OF ALL INTERIOR AND EXTERIOR ITEMS AND SURFACES UNLESS OTHERWISE not-to-be-finish painted, or provide surface-applied protection. Reinstall removed items upon completion of work in . Install units rigid, straight, level, and plumb, with not more than 1, a between pilasters and panels and not more than a � with the setting materials. Fill cracks, holes, and depressions with trowelable leveling and patching compound according INDICATED OR each area. between panels and walls. Provide brackets, pilaster shoes, bracing, and other components required for a complete installation. to tile setting material manufacturer's written instructions. Remove protrusions, bumps, and ridges by sanding or LISTED UNDER EXCLUSIONS BELOW: H. Existing surfaces to be recoated shall be thoroughly cleaned and deglossed by sanding or other means prior to pointin Use theft resistant exposed fasteners finished to match hardware. Use stainless steel tors bolts for through bolt applications. grinding. 1. PAINT ALL EXPOSED SURFACES, EXCEPT AS OTHERWISE INDICATED, WHETHER OR NOT COLORS ARE DESIGNATED. Patched and bare areas shall be spot primed with same primer as specified for new work. 12. STIRRUP BRACKETS: Align brackets at pilasters with brackets at walls. Locate wall brackets so holes for wall anchors occur in 13. Comply with TCA Installation Guidelines Handbook for Ceramic Tile Installation. INCLUDE FIELD PAINTING OF EXPOSED EXTERIOR AND INTERIOR PLUMBING, MECHANICAL AND ELECTRICAL WORK, EXCEPT I. Thoroughly backpaint all surfaces of exterior and interior finish lumber and millwork, including doors and window frames masonry or the joints. There are 3 brackets per connection. 14. Extend tile work into recesses and under or behind equipment and fixtures to form complete covering without AS INDICATED BELOW. trim, cabinetwork, etc., which will be concealed after installation. Backpoint items to be painted or enameled with the 13. Set hinges on in swinging doors to hold open approximately 30 degrees from closed position when unlatched. Set hinges on interruptions, unless otherwise indicated. Terminate work neat) at obstructions, edges, and corners without disrupting 2. PAINT EXTERIOR STUCCO WHERE INDICATED ON DRAWINGS. priming coat. Use a clear sealer for backpriming where transparent finish is required. out swinging doors and swing doors in entrance screens to return to fully closed position. P Y 9 P 9 PROTOTYPE VERSION pattern or joint alignments. J. Bare and covered pipes, ducts, hangers, exposed steel and ironwork, and primed metal surfaces of equipment installed SECTION 10800 - TOILET ACCESSORIES 16U.2.61 15. Lay tile in grid pattern, unless otherwise indicated. Align joints when adjoining tiles on floor, base, walls, and trim are B. Work Included: under mechanical and electrical work shall be cleaned prior to priming. some size. Lay out tile work and center tile fields in both directions in each space or on each wall area. Adjust to 1. The intent and requirements of this Section is that all work, items and surfaces which are normally painted and K. Preparation of other surfaces shall be performed following specific recommendations of the coatings manufacturer. 1. STAINLESS STEEL: ASTM A 666, Type 304, No. 4 satin finish, unless otherwise indicated. minimize tile cutting. Provide uniform joint widths, unless otherwise indicated. finished in a building of this type andquality, shall be so included in this contract whether or not said work g g p p 2. BRASS CASTINGS: ASTM B 19, ASTM r 16, or ASTM B 30. g j g yp L. Bond breakers and curing agents shall be removed and the surface cleaned before rimers, sealers or finish amts ca PROJECT NAME 16. Grout tile per ANSI A108.10, unless otherwise indicated. item or surface is specifically called out and included in the schedules and notes on the drawings, or is, or is be applied. 3. CHROMIUM PLATING: ASTM B 456, Service Condition Number SC 2 (moderate service). 17. Install waterproofing per ANSI A108.13 and manufacturer's written instructions to produce waterproof membrane of not, specifically mentioned in these specifications. M. All drywall surfaces shall be completely dry and dust free before painting. Skim coated drywall shall be sealed with a 4. MIRROR GLASS: ASTM C 1036, Type I, Class 1, Quality q2, with silvering, electroplated copper coating, and protective organic P g P P P p y p sealer recommended b the point manufacturer for this surface. Use theappropriate Ii ht or medium tack masking coating complying with FS DD-M-411. Repair or replace mirrors that develop visible silver spoilage defects within 15 years IN-N-OUT uniform thickness bonded securely to substrate. C. The following general categories of work and items that are included under other sections shall not be a part of this tae y P9 g from date of Substantial Completion. 18. Exterior floor installation on concrete TCA F102 thick set portland cement mortar, or Latex Portland cement mortar. section: tape. Sand portland cement grout. 1. Shop prime painting of structural and miscellaneous iron or steel. 5. GALVANIZED STEEL MOUNTING DEVICEs: ASTM A 153/A 153M, hot dip galvanized after fabrication. BURGER 04 APPLICATION: 19. Interior floor installation on concrete TCA F113, Thin Set Dry set portland cement mortar with latex additive. Standard 2. Shop prime painting of hollow metal work. 3. 6. Use fasteners appropriate to substrate tamper and theft resistant when exposed, and of galvanized steel when concealed. sanded cement grout. 3. Shop finished items. A. Apply painting and finishing materials in accordance with the manufacturer's recommendations. Install units level, plumb, and firmly anchored in locations and at heights indicated. 20. Interior floor installation on waterproof crack suppression membrane over concrete; TCA F122. Thin Set Latex ortlond D. The Room Finish Schedules indicated on the drawings indicates the location of interior room surfaces to be pointed The number of coats specified is the minimum that shall be applied. Apply additional coats when undercoats, stains 7. Install grab bars to withstand all loads per applicable Codes. P PP P g P or other conditions show through final paint coat, until paint film is of uniform finish, color and appearance. 8. Adjust accessories for unencumbered, smooth operation & proper function. Remove temporary labels and protective coatings. � cement mortar, Polymer modified sanded grout. or finished. The schedule indications are general and do not necessarily define the detail requirements. Include all STO C�(f�� 0 N 21. Exterior wall installation over masonry or concrete; TCA W202. Thin Set Mortar: Dry set portland cement mortar. Sand detailed refinements and further instructions as may be given for the required complete finishing of all spaces and B. Apply each material at not less than the manufacturer's recommended spreading rate: portland cement grout. rooms. C. Apply prime coat to surface which is required to be painted or finished. SECTION 11090 - KNOX BOX 22. Interior d location wall installation; thin set mortar; over sum board; TCA W243 or over cementitious backer units; D. Finish exterior doors on tops, bottoms, and edges some as exterior faces, after fitting. 1. REFERENCE STANDARDS: Comply with the current edition of applicable provisions of the following published specifications CALIFORNIA dry gyp E. Sand lightly and dust clean between succeeding coats. P Y PP P 9 P P thin set portland cement mortar with latex additive, TCA W244, standard sanded cement grout. 1.02 SUBMITTALS: 9 Y 9 and standards unless noted otherwise. Key boxes shall bear UL label. 23. Interior damp locations installation over glass mat, water resistant backer board; TCA B419 and TCA W245 thin set A. Product Data: Submit complete manufacturer's descriptive literature and specifications in accordance with the F. Back roll all stucco painting while spraying. 2. Order key boxes from manufacturer using original authorization/order form signed by authority having jurisdiction. Deliver mortar portland cement mortar, Standard sanded cement grout. provisions of Section 01 30 00. key boxes to site in good condition, in original unopened packaging, and with labels intact. Inspect materials upon 5202 PACIFIC AVE 24. Interior wet location installation TCA B415 and TCA W244; over cementitious backer units; or TCA B420 and TCA W245 3.05 CLEANING, TOUCH-UP AND REFINISHING: deliveryand replace damaged or contaminated materials. Ke boxes shall be shipped to contractor. Keys shall be 1. Materials List: Submit complete lists of materials proposed for use, giving the manufacturers name, catalog A. Careful) remove all spattering, sots and blemishes caused b work under this section from surfaces throughout the P 9 Y PP Y over glass mat, water resistant backer board portland cement mortar; standard sanded cement grout. number, and catalog cut for each item when applicable. y P g' p y g shipped directly to authority having jurisdiction. STOCKTION, CA 95207 project. 3. KEY BOXES: Provide Model 3200-RTS recessed mounted heavy duty Ke Boxes, 1 2" solid late door and 1 4" steel B. Samples: In accordance with provisions of Section 01300, submit, on 8-1/2 inch by 11 inch hardboard, samples of Y Y Y / P / B. Upon completion of painting work remove all rubbish, paint cans, and accumulated materials resulting from work in case in aluminum finish, or as required b authority having jurisdiction. SECTION 09513 - DIRECT-APPLIED ACOUSTICAL CEILINGS each color, gloss, texture and material selected by the Architect from standard colors available for the coatings q Y Y 9 each space or room. All areas shall be left in a clean, orderly condition. 4. Locate keybox as shown on drawings. required. B. Runs, sags, misses, holidays, stains and other defects in the painted surfaces, including inadequate coverage and mil PART 1 - GENERAL 1. For natural and stained finishes, provide sample on each type and quality of wood used on the project. thickness shall be satisfactorily touched up, or refinished, or repainted as necessary. 5. Install materials in accordance with accepted shop drawings and manufacturer's printed instructions. 1.1 RELATED DOCUMENTS C. Manufacturer's Instructions: Submit the manufacturer's current recommended methods of installation, including A. DRAWINGS AND GENERAL PROVISIONS OF THE CONTRACT APPLY TO THIS SECTION. THIS INCLUDES GENERAL AND relevant limitations, safety and environmental cautions, application rates, and composition analysis. 3.06 FINISH SCHEDULE: SUPPLEMENTARY CONDITIONS OF DIVISION 01 (1) SPECIFICATION SECTIONS. A. Apply the following finishes to the surfaces specified on the finish schedule or on the drawings. Apply all materials in 1.03 QUALITY ASSURANCE: manufacturer's instructions on properly prepared surfaces and foundation coats. All intermediate IP01111111111114 1.2 DELIVERY, STORAGE AND HANDLING A. Regulatory Requirements: Comply with applicable codes and regulations of governmental agencies having jurisdiction undercoats must accordance with maa tinted to approximate the final color. A. DELIVERY OF ACOUSTIC CEILING PRODUCTS WILL BE IN THE ORIGINAL UNOPENED PACKAGES WITH THE including those having jurisdiction over airborne emissions and industrial waste disposal. Where those requirements 1. Architect will issue n color schedule prior to start l painting to designate the various colors and NmNmOUT MANUFACTURER'S LABEL INTACT conflict with this Specification, comply with the more stringent provisions. locations required for the work. `BURGER B. HANDLING AND STORAGE SHOULD BE IN ACCORDANCE WITH THE MANUFACTURER'S SAFETY DATA SHEETS (SDS) Regulatory changes may affect the formulation, availability, or use of specified coatings. Confirm availability of B. Exterior Systems: coatings to be used prior to job going out to bid and before start of painting project. C. INDIVIDUAL PANELS SHOULD BE HANDLED CAREFULLY TO AVOID DAMAGE g PY p g g g p g p � ( ) 1. Masonry Concrete GOD BLESS AMERICA a. Comply with the current applicable re regulations of the California Air Resources Board CARB and the Environmental a. Gloss - 100% Acrylic 1.3 PROJECT CONDITIONS Protection Agency (EPA). First Coat DE ULTRA-GRIP Premium Primer/Sealer (UGPR00) A. ENVIRONMENTAL LIMITATIONS b. Comply with South Coast Air Quality Management District (SCAQMD) Rule 1113. A copy of this Second Coat ARISTOSHIELD Exterior Gloss Paint (ASHL70) 1. INSTALL ACOUSTIC PANELS ONLY IN CONDITIONS THAT ARE WITHIN THE MANUFACTURER'S PUBLISHED LIMITS FOR regulation can be obtained from http://www.aqmd.gov/rules/reg/reg11/r1113.pdf. Third Coat ARISTOSHIELD Exterior Gloss Paint (ASHL70) TEMPERATURE AND HUMIDITY B. FIELD SAMPLE: WHEN AND AS DIRECTED BY THE ARCHITECT, APPLY ONE COMPLETE COATING SYSTEM FOR EACH COLOR, b. Gloss- 100% Acrylic (Belly Band) 2. AREAS RECEIVING CEILING PANELS SHOULD BE FREE OF CONSTRUCTION DEBRIS AND DUST GLOSS AND First Coat DE ULTRA-GRIP Premium Primer/Sealer (UGPR00) 3. MECHANICAL, SPRINKLER AND ELECTRICAL TRADES SHALL HAVE COMPLETED THEIR WORK ABOVE THE CEILING TEXTURE REQUIRED. WHEN APPROVED, THE SAMPLE PANEL AREAS WILL BE DEEMED INCORPORATED INTO THE WORK AND Second Coat ARISTOSHIELD Exterior Gloss Paint (ASHL70-0-221-1) PROJECT NUMBER STRUCTURE PRIOR TO COMMENCEMENT OF THE CEILING PANEL INSTALLATION WILL SERVE AS THE STANDARDS BY WHICH THE SUBSEQUENT WORK OF THIS SECTION WILL BE JUDGED. Third Coat ARISTOSHIELD Exterior Gloss Paint (ASHL70-0-221-1) 190955 1.4 COORDINATION 2. CONCRETE BLOCK - CMU A. COORDINATE THE INSTALLATION OF THE ACOUSTIC CEILING SYSTEM WITH ANY AND ALL TRADES WHOSE WORK IS 1.04 DELIVERY, STORAGE, AND HANDLING: a. GLOSS - 100% ACRYLIC SHEET TITLE IMPACTED BY THAT INSTALLATION A. STORAGE AND PROTECTION: USE ALL MEANS NECESSARY TO PROTECT THE MATERIALS OF THIS SECTION BEFORE, DURING, FIRST COAT SMOOTH BLOCFIL PREMIUM CONCRETE BLOCK FILLER (SBPR00) AND AFTER SECOND COAT ARISTOSHIELD EXTERIOR GLOSS PAINT (ASHL70) SPECIFICATIONS 1.5 EXTRA MATERIALS INSTALLATION. THIRD COAT ARISTOSHIELD EXTERIOR GLOSS PAINT (ASHL70) A. PROVIDE EXTRA MATERIALS IN THE MANUFACTURER'S UNOPENED PACKAGING, WITH THE MANUFACTURER'S LABEL B. DELIVER MATERIALS TO JOB SITE IN NEW, ORIGINAL, AND UNOPENED CONTAINERS BEARING MANUFACTURER'S NAME AND b. GLOSS- 100% ACRYLIC (BELLY BAND) INTACT, AS DETAILED BELOW TRADE NAME. FIRST COAT DE ULTRA-GRIP PREMIUM PRIMER/SEALER (UGPROO) LO Cp 1. ACOUSTIC PANELS - MINIMUM 5% OF EACH TYPE INSTALLED STORE WHERE DIRECTED IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS. SECOND COAT ARISTOSHIELD EXTERIOR GLOSS PAINT (ASHL70-0-221-1) zd- PART 2 - PRODUCTS 1.05 PROJECT CONDITIONS: THIRD COAT ARISTOSHIELD EXTERIOR GLOSS PAINT (ASHL70-0-221-1) A. DO NOT APPLY EXTERIOR MATERIALS DURING FOG, RAIN OR MIST, OR WHEN INCLEMENT WEATHER IS EXPECTED WITHIN THE 3. FERROUS METAL 0 2.1 MANUFACTURER DRY TIME a. GLOSS - WATERBORNE ALKYD / 100% ACRYLIC CD Of `D A. SAINT-GOBAIN / CERTAINTEED CEILINGS (NO ALTERNATES ACCEPTED) SPECIFIED BY THE MANUFACTURER. NO EXTERIOR OR INTERIOR PAINTING SHALL BE DONE UNTIL THE SURFACES ARE FIRST COAT AXALTA IMRON IND 9P01 PRIMER SHEET NUMBER CD CD � 1. ADDRESS: 20 MOORES ROAD, MALVERN, PA 19355 THOROUGHLY DRY SECOND COAT AXALTA IMRON IND 9T01 FINISH COAT 2. TELEPHONE: 800-233-8990 AND CURED. DO NOT APPLY PAINT WHEN TEMPERATURE IS BELOW 50' F. AVOID PAINTING SURFACES WHEN EXPOSED TO THIRD COAT AXALTA IMRON IND 9T01 FINISH COAT Q 3. WEB: WWW.CERTAINTEED.COM/CEILINGS DIRECT o 4. INOB PREFERRED PRICING CAN BE OBTAINED THROUGH WESTSIDE BUILDING SUPPLY (CA) SUNLIGHT. Al ■ zz � Q__