WORK PLANS - Laserfiche WebLink

Home Browse Search

REVISIONS BY HOOD SYSTEM NOTES 1-1/2" x 1-1/2" x 3/6"ANGLE 1. HOOD PERFORMANCE TEST IS REQUIRED PER CMC 509.11. BLOCKING, AS REQUIRED 2. MAINTAIN A CLEARANCE FROM COMBUSTIBLE MATERIALS OF NOT LESS THAN 18" FROM THE HOOD. THIS MAY BE REDUCED TO NOT LESS THAN 3" PROVIDED THE COMBUSTIBLE MATERIAL IS PROTECTED WITH ONE-HOUR RATED MATERIAL PER CMC SEC. 507.2.1. %4" O x 2-1/2" SDS SCREW 3. OUTLET OF FAN SHALL TERMINATE A MINIMUM OF 10'-0" AWAY FROM ANY AIR INLET OR TOP AND BOTTOM CORNERS AIR-INTAKE AND 10'-0" FROM ANY PROPERTY LINE. OF HOOD, TYPICAL (4 LOCATIONS) 4. MAINTAIN A MINIMUM 10'-0" SEPARATION BETWEEN EXHAUST OUTLET AND MAKE-UP AIR INTAKES. #12 SMS TYPICAL AT HOOD CANOPY z DETAIL A 10'-0" MINIMUM UP-BLAST EXHAUST FAN W tO SEE MECHANICAL SCHEDULE APPROVED BY THE L.A. MECHANICAL Ln r- 2x12 BLOCKING WITH SIMPSON 'B' HANGAR TESTING LABORATORY APPROVAL#RR-7851 Vm 00 AT EACH END, TYPICAL, AS REQUIRED w Ln � MAKE-UP AIR UNIT L NSF In SEE MECHANICAL SCHEDULE IN-TAKE I GREASE TROUGH LISTED In - FILE#24 MU L] Q 00 ------ HINGE KIT B --- - NOTE: V GENERAL CONTRACTOR TO Lu Q SEE DETAIL PROVIDE THE DUCTWORK i � ;� � � THAT CONNECTS FROM THE � � N MAKE-UP AIR RETURN SYSTEM Q / ON THE ROOF TO THE SUPPLY F_ AIR REGISTER(S) AS SHOWN J L] X = o w Q 3" X 13" X 1/4" L-BRACKET WITH > Q LL DOUBLE NUT CONNECTION AT TOP El Q EXISTING ROOF FRAMING TO REMAIN -VERIFY SPACING AND SPAN Z Q Q n VENTILATOR SYSTEM NOTES m WLn W Ln EXHAUST FAN MOUNTING CURB TO j w BE PROVIDED BY THE EXHAUST 1. EXHAUST AIR VOLUMES SHOWN ON THIS DRAWING ARE CRITICAL TO SYSTEM PERFORMANCE. FAN SYSTEM MANUFACTURER VOLUMES MUST BE MAINTAINED WITHIN -5%, +10%TOLERANCE. STATIC PRESSURE SHOWN ARE a w ' FOR VENTILATOR AND DUCT COLLAR ONLY. 0� w A. ADD STATIC PRESSURE OF DUCTWORK SUPPLIED BY OTHERS TO OBTAIN TOTAL I DETAIL'A' SYSTEM PRESSURE FOR FAN SELECTION. Ln NOTE: 2. DUCTWORK MUST BE FULLY WELDED LIQUID-TIGHT AND PITCHED TOWARDS VENTILATOR. DO .-. IF HOOD IS ADEQUATELY o SUPPLY AIR REGISTER NOT CONNECT NON-COOKING EQUIPMENT EXHAUSTS TO THIS SYSTEM. PROVISIONS FOR 0 a) ATTACHED TO THE WALL, N SEE CAPTIVE AIRE HOOD DRAWINGS BALANCING STATIC PRESSURES MUST BE MADE WHEN CONNECTING VENTILATORS OF W wTHEN LATERAL BRACING IS DETAIL'A' NOT REQUIRED ------- DIFFERENT STATIC RATINGS. I N (SIM) 3. ELECTRICAL CONNECTIONS SHOWN CONSISTING OF: ... A. POWER SUPPLY(S) k I B. INTERCONNECTING CONTROLS AND SWITCH FOR HOOD. C. LIGHT IS NOT PROVIDED BY HOOD MANUFACTURER UNLESS SPECIFICALLY a 1/2" DIAMETER ALL THREAD ROD NOTED ON DRAWINGS. LOCATED AT CORNERS OF EXHAUST 0 MINIMUM 3" SEPARATION FROM HOOD CANOPY TO HOOD AND RETURN AIR PLENUMS WALL PER 2016 CBC 507.3 DOUBLE NUT NOTE: VERIFY WITH HOOD MANUFACTURER'S SPECIFICATIONS CONNECTION AT BOTTOM STAINLESS STEEL TRIM/ENCLOSURE TO COVER El THE EXHAUST HOOD AND RETURN AIR PLENUMS SEE ARCHITECTURAL DRAWINGS FOR FINSH MATERIALS BEHIND COOKING ��SED JA BCy�T EQUIPEMTN oOP� Rye J I ~ C-25449 p -III -III -III -III -III -III -III -III -III -III -III -III -III -IIIH HIII III III IIII I H H H H H IHI IHI I IL H H H IFS RENEWAL DATE =1 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I ii 111 I i1 111 I i1 111 I i1 111 I i1 111 I i1 i 11 I i1 i 11 I i1 i 11 I i1 i 11 I i1 i 11 111 i 11 111 i 11 111 i 11 111 i 11 111 i 11 111 i 11 111 i 11 111 i 11 111 � � I 1=1 I 1-1 111 I 1-1 111 I I1 111 I I1 111 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I 1-1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I I1 111 I L �T� O� OF CAL�� SCALE: 1 EXHAUST HOOD SECTION v crumbl 6„ cookies BLOCKING, MINIMUM 2x6 @ 8'-0" SPAN p MIN. INTERIOR TENANT B OR (2) 2x6 @ 10'-0" SPAN IMPROVEMENT EXISTING 2x6 RAFTER LOCATION EXISTING 2x6 RAFTER TO REMAIN (2)Y2" 864 W. BENJAMIN HOLT DR. TO REMAIN THROUGH BOLTS — STOCKTON, CA 95207 d A.P.N.: 09741060 w L rFln0 0 FRANCHISE OWNER o M KTK CO. V _____ 2 x 6 BLOCKING ------------- 3966 GLEN ABBY CIRCLE STOCKTON, CA (2) 1/2" 0 THROUGH BOLTS 95219 WITH NUTS AND WASHERS L 3 x 3 x 1/4" 6" LONG AT EACH VERTICAL ROD — SIMPSON LUS HANGER DRAWN TAF \ 1/2" O THREADED SIMPSON LUS HANGER CHECKED I EQ• ROD (MIN.) \ 1/2" 0 THREADED ROD (MIN.) SLW DATE L3 x 3 x 1/4" -6" LONG AT 5/25/2021 EACH VERTICAL ROD SCALE AS SHOWN ATTACHMENT AT BLOCKING HANGER ATTACHMENT JOB NO. A B 21-136 SHEET 2 EXHAUST HOOD MOUNTING 1 SCALE-1 -o" OF SHEETS