INSTALL_2021 - Laserfiche WebLink

Home Browse Search

& was able to access again without any problem) we can overnight hard copies or a usb drive including all plans & documents to your office, if manufacturer's cut sheets are still not the correct ones, please advise specifically which ones are acceptable & which ones you are still missing. utas for the following were not submitted: • tank STP sump and tank fill sump Under Dispenser Containment —The application lists B-925x-FXL BD -AB but that is not one of the part numbers on the Bravo B-9000 cut sheet. This cut sheet also states that this is a single walled UDC. Will you be installing a single walled UDC? Electrical penetrations F -17 -RR -D and F -10 -RR -D - not listed on the Bravo cut sheet submitted. • Franklin Fueling FF10X12HMX346 flex connect is not listed on the Flex-ing Flex Connector cut sheet. Or is the end of this part supposed to be "...F346"? Then it woLA fit something on this cut sheet. 3) Provide tank charts for the tanks being used. Please follow the link to access updated plans, see sheets M.5.3.04, M.5.3.05, M.5.3.06. These page with values that list the that list the dipstick value associated with the gallons in the tank. See example below of a tank chart. There are multiple pages that list various values of the fuel level and volume of the fuel. Sheets M.5.3.04, M.5.3.05, M.5.3.06 are diagrams of the tank with details. <image003.jpg> 4) The section on vacuum zones on M.5.3.09 lists vapor recovery under 87 Zone 1 only. Please include documentation for 91 vapor recovery piping. 91 on this page only shows vacuum zones for product (zone 5), vent (zone 6) and crossover (zone 7). Please follow the link to access updated plans, see revised sheet M.5.3.0 (Detail D). The install plans in the link does not have a page M.5.3.0. There are 5.3.0,, M.5.3.02, M.5.3.04, M.5.3.05, M.5.3.06, and M.5.3.09 but no pages that are a plain Q 5) Provide line length information for verifying line leak detector compatibility. 1 don't see the line length information on G.0.2.0. Please follow the link to access updated plans, see revised sheet M.5.3.0 (Detail DSR). The install plans in the link does not have a page M.5.3.0. There are M.77770? M S-04, M.5.3.05, M.5.3.06, and M.5.3.09 but no pages that are a plain M.5.3.0 6) Provide completed UPCF Underground Storage Tanks — Facility form (A) and UPCF Underground Storage Tanks (B) —Tank (one form per tank). Can this be a condition that forms for ust system/equipment installed will be submitted prior to final nn this one with a sup jML 7) Tank sizes on the application does not match tank sizes in the installation plans. page 3 and 6 of the application list that there will be two 20,000 gallon tanks and one 25,000 gallon tank. The installation plans (page M.5.3.01) list two 25,000 gallon tanks and one 20,000 gallon tank. Please clarify by updating the application or updating the install plans. 8) Striker plates are not shown on the tank section detail for the 8,000 gallon tank (M.5.6.03). Striker plates or drop tube -mounted bottom protectors should be illustrated below all accessible openings. 9) 1 wanted to verify: a. All the tank fill sumps will have OPW spill containers, except for the Diesel only tanks which will have both OPW and Franklin Fueling spill containers? b. Will all the OPW spill containers be OPW 1-2100-EVR? This is the cut sheet submitted but the listed part number on the application is PK2-40FLMP-S. Is that a packaged part number that includes the 1-2100-EVR? c. The install plans for the tank section details for OPW fill sumps show to look at A, B, C on M.5.3.17, but that page only has A, D, E, F, G (no B or C). Are there B and C on an updated page? 20