|
PLUMBING LEGEND GENERAL PLUMBING NOTES
<br /> SYMBOL DESCRIPTION 1. ALL WORK SHALL COMPLY WITH ALL APPLICABLE CODES, SPECIFICATIONS, LOCAL VS
<br /> �'+ �'+
<br /> ORDINANCES AND INDUSTRY STANDARDS. VSAC DESI G N
<br /> SOIL, WASTE OR SANITARY SEWER BELOW GRADE OR SLAB
<br /> --GW-- GREASE WASTE BELOW GRADE 2• SEISMIC RESTRAINT: PIPING SHALL BE SUPPORTED AND BRACED IN ACCORDANCE
<br /> WITH THE CBC AND THE LATEST EDITION OF SMACNA "GUIDELINES" FOR SEISMIC P❑ BOX 163686
<br /> --AW-- ACID RESISTANT WASTE BELOW GRADE
<br /> ------- VENT PIPING RESTRAINTS OF PLUMBING SYSTEMS AND MECHANICAL SYSTEMS. Sacramento, CA 95816
<br /> COLD WATER PIPING 3. ALL INSULATION AND SEALING PRODUCTS USED IN THE BUILDING SHALL HAVE A SURFACE Tell 916,752,2022
<br /> GAS METER CSPREAD/SMOKE
<br /> DEDEVELOPED
<br /> HOT WATER PIPING MAXMUM, WHEN TESTED AS 0 POSITENSTALLL.ATIONINC UDNGINSULATION, TAPES
<br /> 50
<br /> 100-ft TDL ❑ FAN COIL
<br /> G GAS PIPING - PRESSURE NOTED FACING MATERIALS, JACKETS AND ADHESIVES.
<br /> C9 CD CONDENSATE DRAIN PIPING 4. THE ANNULAR SPACE BETWEEN PIPE SLEEVES AND THE PIPE THROUGH ALL RATED WALLS
<br /> AND FLOORS SHALL BE FIRESTOPPED. FIRESTOPPING OF ALL PIPE PENETRATIONS SHALL
<br /> D�I AUTOMATIC GAS SHUT-OFF VALVE COMPLY WITH U.L REQUIREMENTS. MANUFACTURER PREAPPROVED UL PENETRATION FOR
<br /> N I The use of these drawings and
<br /> PIPE MATERIAL AND SURFACE PENETRATED SHALL BE USED. PENETRATIONS SHALL BE
<br /> T SLOPE PIPING AS MUCH PROVIDE CLEANOUTS GCO, FCO GRADE CLEAN OUT, FLOOR CLEAN OUT 3M, PROSET, OR APPROVED EQUAL SUBMIT SHOP DRAWINGS. specifications Shall be restricted to
<br /> (E) C.W. AS POSSIBLE TOWARD IN TURNS/ENDS OF CLEANOUT, WALL CLEANOUT 5. COORDINATE THE FOLLOWING WITH ARCHITECTURAL, STRUCTURAL, PLUMBING AND ELECTRICAL the Specific site for which they were
<br /> FD FLOOR DRAIN DRAWINGS AND ELEMENTS AS INSTALLED, INCLUDING EXISTING BUILDING SYSTEMS: prepared and publication thereof
<br /> DISCHARGE TYPICAL PIPE TYPICAL FS FLOOR SINK A, EXACT LOCATION OF ALL EQUIPMENT. shall be expressly limited to such
<br /> > > B. ALL PENETRATIONS THRU ROOF, WALLS AND FLOORS.
<br /> + -l_4- POC POINT OF CONNECTION C. EXACT SIZE AND ROUTING OF DUCTWORK AND PIPING. use. Re-use, reproduction or
<br /> TYP. TYPICAL publication by any method in whole
<br /> CONDENSATE N NEW 6. ALL PIPING LOCATED IN WALLS OR ABOVE CEILING HAVING SHUTOFF VALVES OR OTHER or part is prohibited. Title to these
<br /> INDIRECT WASTE ( ) DEVICES REQUIRING ACCESS FOR OPERATION OR MAINTENANCE SHALL BE PROVIDED IanS and s ecifications shall remain
<br /> PIPING (E)F , EXISTING EXISTING TO BE FIELD VERIFIED BY CONTRACTOR WITH ACCESS DOORS OF ADEQUATE SIZE FOR SERVICE. P P
<br /> PIPING PROVIDE VENTED V, vR, VTR VENT, VENT RISER, VENT THRU ROOF with VSAC Design without prejudice,
<br /> O 7. ANY DAMAGE TO EXISTING BUILDING ARCHITECTURAL, STRUCTURAL, MECHANICAL AND and Visual contact with them Shall
<br /> W, WD WASTE, WASTE DROP ELECTRICAL SYSTEMS THAT OCCURS DURING THE WORK SHALL BE RESTORED TO THE
<br /> P-TRAP AT FAN ORIGINAL CONDITION AT THE CONTRACTOR'S EXPENSE. constitute prima facie evidence of
<br /> C HW, HWD, HWR HOT WATER, HOT WATER DROP, HOT WATER RISER acceptance of these restrictions.
<br /> 0 0 FS FIN. FLOOR MIN 2" COIL, TYPICAL CW, CWD, CWR COLD WATER, COLD WATER DROP, COLD WATER RISER 8. LOCATIONS, SIZES AND DEPTHS SHOWN FOR ALL EXISTING UTILITIES AND EQUIPMENT SHOWN P
<br /> 1" HW & CW
<br /> TDL TOTAL DEVELOPED LENGTH ARE APPROXIMATE ONLY. CONTRACTOR SHALL FIELD VERIFY THE EXACT SIZE, LOCATION © VSAC Design
<br /> ° o. o o o AND ADEQUACY OF DEPTH OF ALL EXISTING UTILITIES AND/OR EQUIPMENT SHOWN TO BE
<br /> o ° ° ROUTE PIPING INCONSPICUOUSLY CONNECTED TO PRIOR TO BEGINNING WORK.
<br /> I o
<br /> € ° ° 0. 0 AND UNOBTRUSIVELY. HANG PIPE
<br /> ❑
<br /> AS REQUIRED. DO NOT INSULATE PLUMBING SCHEDULE SYMBOL DESCRIPTION PIPE MATERIAL SCHEDULE REVISIONS By
<br /> 0
<br /> ���-- --- ------------- - FLOOR SINK INDIRECT DRAIN PIPE WHEN EX-
<br /> POSED I IN FOOD SERVICE FACILITY.
<br /> PLUMBING CONTRACTOR SHALL FURNISH AND INSTALL FIXTURES IN THIS WASTE, VENT AND STORM PIPING
<br /> SCHEDULE OR THEIR APPROVED EQUIVALENT. REFER TO ARCHITECTURAL ABS (ACRYLONITRILE-BUTSFIENE-STYRENE) PLASTIC PIPE. ALL PIPE, COUPLINGS AND
<br /> DRAWINGS FOR ALL MOUNTING HEIGHTS OF FIXTURES. FITTINGS SHALL BE MANUFACTURED OF MATERIAL CONFORMING TO ASTM D 2661. PLASTIC
<br /> SOLVENT CEMENT FOR ABS PLASTIC PIPE SHALL CONFROM TO ASTM D 2235.
<br /> ❑❑
<br /> 3ACID RESISTANT WASTE & VENT
<br /> SCHEDULE 40 PVC (POLYVINYL CHORIDGE) PLATIC PIPE. ALL PIPE, COUPLINGS AND
<br /> FITTINGS SHALL BE MANUFACTURED OF MATERIAL CONFORMING TO ASTM D 1785. PLASTIC
<br /> "P" TRAP
<br /> FLOOR SINK: J.R. SMITH #345-YO3 WITH CAST IRON BODY, ENAMELED SOLVENT CEMENT FOR PVC PLASTIC PIPE SHALL CONFROM TO ASTM D 2235.
<br /> 1-1/2"G
<br /> fa INTERIOR, 10" DEEP SUMP, FLANGE AND SEEPAGE PAN, ALUMINUM CONDENSATE DRAIN PIPING:
<br /> BOTTOM DOME STRAINER, HALF GRATE, 3" OUTLET, CAULK JOINT. TYPE DWV COPPER TUBING AND FITTINGS OR SCHEDULE 40 GALVANIZED STEEL PIPE AND
<br /> MALLEABLE IRON FITTINGS. (PVC PIPING WILL NOT BE ACCEPTABLE)
<br /> EWATER PIPE (HOT AND COLD WATER):
<br /> EXISTING ELECTRIC WATER HEATER:
<br /> 50GAL TYPE L BELOW GRADE, TYPE M ABOVE GRADE, COPPER TUBING, HARD-TEMPER, WITH
<br /> WROUGHT COPPER FITTINGS. SOLDERING/BRAZING MATERIAL SHALL BE LEAD FREE, SILVER
<br /> ❑ REPLACE (1) 5.5 KW ELEMENT WITH (2) 4.5 KW ELEMENTS. SOLDER BELOW GRADE, 95-5 OR SIMILAR ABOVE GRADE. CAPPED OR PLUGGED OUTLETS
<br /> INDIRECT TO FLOOR SINK SIMULTANEOUS OPERATION - 9 KW TOTAL SHALL
<br /> 240V/1PHASE SCREWEDD SCHEDULE 40 SCREWED BRASS. ELBOWS AT BRANCH OUTLETS SHALL BE
<br /> OUTLET, WITH EARS, FOR NAILING OR SCREWING TO WALL BACKING.
<br /> ==n
<br /> GAS PIPING:
<br /> SCALE: N.T.S. BLACK STEEL, STM A-53, WITH MALEABLE STEEL FITTINGS. PIPE SIZES 3" AND OVER
<br /> GREASE TRAP: AUTOMATIC BIG DIPPER W-350-IS 35 GPM FLOW SHALL HAVE WELDED JOINTS; SIZES 2-1/2" AND SMALLER MAY BE THREADED OR
<br /> STI RATE, 3" INLET AND OUTLET. 115 VAC, 50/60 Hz, 1173 W, WELDED, AT CONTRACTOR'S OPTION, EXCEPT THAT ALL PIPING UNDERGROUND SHALL BE
<br /> 10.2 A WELDED, REGARDLESS OF SIZE.
<br /> NOTE:
<br /> 1. PIPING INSTALLED IN, OR OUTSIDE, WALL BEHIND THE OR ABOVE THE COOK LINE
<br /> SHALL BE METALLIC.
<br /> 2. PROVIDE METALLIC PENETRATIONS AT 1-HR. WALLS AND ALL METALLIC PIPE IN
<br /> 2-HR WALLS
<br /> WATER & GAS PLAN
<br /> SCALE: 1/4" - 1'-0" 1 FIXTURE CONNECTION SCHEDULE w
<br /> Q
<br /> WASTE WATER GAS � 7
<br /> HYDROMECHANICAL SYMBOL FIXTURE DESCRIPTION VENT DIRECT IND. CW HW BTUH L
<br /> GREASE INTERCEPTOR (HGI) SIZING - Q
<br /> 3-COMP SINK 2 - 3 1/2 1/2 - r ) O
<br /> GAS PIPING EXPOSED ALONG BACK WALL BEHIND KITCHEN EQUIPMENT. CPC TABLE 1014.2.1: PREP SINK - - 2 1/2 1/2 V
<br /> HAND SINK 1-1/2 - 1-1/2 1/2 1/2 - z J
<br /> FOR 2-MIN DRAINAGE PERIOD:
<br /> SHUTOFF VALVE-TYPICAL. p 3"0 GREASE WASTE PIPE W/ MAX FULL PIPE FLOW OF 60 GFM Q Q
<br /> Vag REQUIRES 35 GPM HGI 2i 0
<br /> DRIP LEG-TYPICAL.
<br /> 2"0 GREASE WASTE PIPE W/ MAX FULL PIPE FLOW OF 20 GFM Q
<br /> REQUIRES 10 GPM HGI r/1
<br /> SWIVEL 360°ROTATION FITTING.
<br /> 2" V CONNECTED TO
<br /> \\
<br /> (E) VTR \ (� w
<br /> GAS PRESSURE REGULATOR-
<br /> ff. ff ttl.
<br /> ❑ TYPICAL.
<br /> 0 0 \ PROVIDE BLOCKING BEHIND ®' z
<br /> FS WALL TO SECURE- ®�®
<br /> TYPICAL. ®9� ® � ® Z
<br /> T j ®0� a ®® ® GAS PIPE SIZING CALCULATION BTU/H CFH PIPiN SIZE WATER AND WASTE SERVICE CALCULATIONS C
<br /> E�nlRESTRAINING CABLE-TYPICAL. ® JOB NAME: JJs HAWAIAN BBQ&TEA DATE: 12116120 C
<br /> ®p DEMAND: TOTAL
<br /> WASTE COLDVW►TER HOT WATER VOTER
<br /> 24"GRIDDLE 60,000 60 314 FIXTURE TYPE NO. Fu TOTAL Fu TOTAL Fu TOTAL Fu
<br /> ElHOSE GAS CONNECTOR,HEAVY DUTY, 4-BURNER RANGE 155,000 155 1 LAVATORY(SINGLE) 1 1 1 1 1 1 1 1.3
<br /> FLEXIBLE,CORRUGATED TYPE 304 FRYER 70,000 70 3/4
<br /> r -- --- ------------- STAINLESS STEEL TUBING WITH STAINLESS (E)RTU-1 100,000 100 3/4 MOP SINK 1 3 3 3 3 3 3 4
<br /> STEEL BRAID AND ANTIMICROBIAL PVC (E)RTU-2 100,000 100 3/4 FLOOR DRAIN 1 2 2 0 0 0 ?
<br /> 0
<br /> COATING-TYPICAL. (E)WATER HEATER 36,000 36 FLOOR SINK RECEPTOR 2 3 6 0 0 0 0 0
<br /> UNDER EACH CASTER-TYPICAL. HAND SINK 2 2 4 1 2 1 2 2.7
<br /> ® TYPICAL GAS FIRED KITCHEN
<br /> TOTAL 521,000 521 PREP SINK 1 0 2 2 2 2 2.7
<br /> T0o:
<br /> SAFETY-SET POSITIONING SYSTEM EQUIPMENT. 3-COMP SINK 1 3 3 3 3 225 225 4.0
<br /> DEVELOPED LENGTH 100® URINAL,1.0 GPF 2 0 20 0 0 0 0
<br /> PIPE SIZE AS PER CPC TABLE 1216.2(l) 1-112" WATER CLOSET,1.6 TANK 1 6 6 3.5 3.5 0 0 3.5
<br /> (E) 3" W 1
<br /> 3 GAS APPLIANCE NOTE: Drawing
<br /> = I TOTAL FU 25.0 14.5 10.3 1 18.2
<br /> M EQUIVALENT COLD WW4TER FLOW RATE(GPM):
<br /> 14
<br /> 1. APPLIANCE AND/OR LINE GAS REGULATORS ARE DORMONT BRAND OR EQUIV. ADDITIONAL DEMAND LOAD(GPM) 0
<br /> APPLIANCE GAS REGULATOR IS TO CONFORM TO ANSI Z21.18 PRESSURE AVAILABLE ATMAIN(PSI): 40
<br /> LINE GAS REGULATOR IS TO CONFORM TO ANSI Z21.80 MINIMUM REQUIRED FIXTURE PRESSURE(PSI): 8 PLUMBING PLANS
<br /> ELEVATION RISE(FT): 6
<br /> METER LOSS(PSI): 4
<br /> 2. PROVIDE RESTRAINING CABLE & DORMONT BLUE HOSE CONNECTOR BACKFLOWPREVENTERLOSS(PSI): 12
<br /> FOR MOVEABLE GAS APPLIANCES. CONNECTOR TO CONFORM W/ ANSI Z21.69 ADDITIONAL LOSSES(PSI): 0
<br /> & NSF/ANSI 169 EQUIVALENT PIPE LENGTH FROM METER TO MOST REMOTE FIXTURE(FT): 120
<br /> FRICTION LOSS PRESSURE AVAILABLE(PSI): 13.40
<br /> MAXIMUM ALLOWABLE FRICTION LOSS(PSI/100 FT): 11.16
<br /> WATER FLOW VELOCITY(FPS): 5.44
<br /> CALCULATED FRICTION HEAD LOSS(PSI/100 FT): 6.49
<br /> MINIMUM REQUIRED'WATER'PIPE SIZE(INCHES): 1.0
<br /> MINIMUM REQUIRED'WASTE'PIPE SIZE(INCHES): 3 QROFESS/0/9
<br /> (CALCULATIONS PER THE UPC/CPC) c` '`C� N D. l
<br /> WASTE 8c VENT PLAN NO60696
<br /> WATER PIPE SIZING CHART :* . ;
<br /> S ' EXP. 12/31/20
<br /> SCALE: 1 Q ;
<br /> PIPE SIZES CALCULATED BASED ON UPC/CPC APPENDIX A
<br /> yTF .
<br /> SIZE_TYPE L COPPER CW MAX FLOW CW FIXTURE UNIT VALUES HW MAX FLOW HWFU of CA`\�Qi"
<br /> NOMINAL INTERNAL GPM FPS FLUSH TANK FLUSHVALVE GPM FPS HOT WATER
<br /> DIAMETER DIAMETER
<br /> 112' 0.545 2.4 3.3 1 0 24 33 1
<br /> 314" 0.785 6.3 4.1 7 0 6.3 4.1 7
<br /> 1" 1.025 12.6 4.9 16 0 12.6 4.9 16
<br /> Proj. No.
<br /> 1-114" 1.265 21.9 5.6 32 0 19.6 5.0 26
<br /> 1-117' 1.505 34.7 6.2 63 18 27.7 5.0 46 Drawn HDV
<br /> 2" 1.985 71.8 7.4 1 231 1 112 1 48.2 5.0 1 119 :F
<br /> Date 12/16/2020 0
<br /> Q
<br /> Scale 0
<br /> Sheet
<br /> P 1
<br /> Sheet No. of Total Sheets
<br />
|