|
CODE REQUIREMENTS (CBC) ACCESSIBILITY NOTES ACCESSIBILITY NOTES (CONT.)
<br /> ACCESSIBLE ROUTES FLOOR OR GROUND SPACES (CONT.) DOORS AND DOORWAYS (CONT.)
<br /> 11B-206.2.1 SITE ARRIVAL POINTS.AT LEAST ONE ACCESSIBLE ROUTE SHALL BE 11B-306.2.2 MAXIMUM DEPTH. TOE CLEARANCE SHALL EXTEND 25 INCHES (635 MM) �r
<br /> VO VO PROVIDED WITHIN THE SITE FROM ACCESSIBLE PARKING SPACES AND MAXIMUM UNDER AN ELEMENT, TYPE OF USE MINIMUM MANEUVERING CLEARANCE
<br /> ACCESSIBLE PASSENGER LOADING ZONES; PUBLIC STREETS AND SIDEWALKS;
<br /> AND PUBLIC TRANSPORTATION STOPS TO THE ACCESSIBLE BUILDING OR FACILITY 11B-306.2.3 MINIMUM REQUIRED DEPTH. WHERE TOE CLEARANCE IS REQUIRED AT PARALLEL TO
<br /> ,AO'C �O'C ENTRANCE THEY SERVE. WHERE MORE THAN ONE ROUTE IS PROVIDED, ALL AN ELEMENT AS PART OF A CLEAR FLOOR SPACE, THE TOE CLEARANCE SHALL APPROACH DIRECTION DOOR OR GATE SIDE PERPENDICULAR TO DOORWAY(BEYOND DOORWAY LATCH SIDE UNLESS
<br /> ROUTES MUST BE ACCESSIBLE. EXTEND 17 INCHES (432 MM) MINIMUM UNDER THE ELEMENT. NOTED)
<br /> 11B-206.2.2 WITHIN A SITE.AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT 11B-306.2.4 ADDITIONAL CLEARANCE. SPACE EXTENDING GREATER THAN 6 FROM FRONT PULL 60 INCHES (1524 MM) 13 INCHES(4.57'%:1
<br /> `DSP `DSP ACCESSIBLE BUILDINGS, ACCESSIBLE FACILITIES, ACCESSIBLE ELEMENTS, AND INCHES (152 MM) BEYOND THE AVAILABLE KNEE CLEARANCE AT 9 INCHES (229 MM) FROM FRONT PUSH 48 INCHES (1219 MM) D INCHES (0 h;l?;I; ©2020 STARBUCKS COFFEE COMPANY
<br /> ACCESSIBLE SPACES THAT ARE ON THE SAME SITE. ABOVE THE FINISH FLOOR OR GROUND SHALL NOT BE CONSIDERED TOE FROVA HINGE SIDE PULL 60 INCHES (1524 MM) 36 INCHES(914 MM',
<br /> CLEARANCE. 44 INCHES(1115 STARBUCKS'
<br /> 11B-206.2.4 SPACES AND ELEMENTS. AT LEAST ONE ACCESSIBLE ROUTE SHALL FROM HINGE SIDE PUSH 22 INCHES(559Iv1h9)°
<br /> CONNECT ACCESSIBLE BUILDING OR FACILITY ENTRANCES WITH ALL ACCESSIBLE 11B-306.2.5 WIDTH. TOE CLEARANCE SHALL BE 30 INCHES (762 MM)WIDE MINIMUM. AIM)
<br /> � SPACES AND ELEMENTS WITHIN THE BUILDING OR FACILITY, INCLUDING FROM LATCH SIDE PULL 60 IN HES (1524 A41.4) 24 INCHES(610 PAM) 2401 UTAH AVENUE SOUTH
<br /> MEZZANINES, WHICH ARE OTHERWISE CONNECTED BY A CIRCULATION PATH 11B-306.3 KNEE CLEARANCE. FROM LATCH SIDE PUSH 44 INCHES(1115 24 INCHES(610 MM) SEATTLE, WASHINGTON 98134
<br /> UNLESS EXEMPTED BY SECTION IIB-206.2.3 EXCEPTIONS 1 THROUGH 7. A'IA44
<br /> W\E ��\ ADD 12 INCHES(305 MM) IF CLOSER AND LATCH ARE PROVIDED. (206) 318-1575
<br /> 11B-306.3.1 GENERAL. SPACE UNDER AN ELEMENT BETWEEN 9 INCHES (229 MM)
<br /> 11B-206.2.5 RESTAURANTS, CAFETERIAS, BANQUET FACILITIES AND BARS. IN AND 27 INCHES (686 MM)ABOVE THE FINISH FLOOR OR GROUND SHALL BE ADD 4 INCHES(102 VM) IF CLOSER AND LATCH ARE PRDVIDED.BEYOND HINGE SIDE. THESE DRAWINGS AND THE PROJECT MANUAL
<br /> RESTAURANTS, CAFETERIAS, BANQUET FACILITIES, BARS, AND SIMILAR CONSIDERED KNEE CLEARANCE AND SHALL COMPLY WITH SECTION I IB-306.3. ADD 4 INCHES(102 MIND IF CLOSER IS PROVIDED. ARE CONFIDENTIAL AND SHALL REMAIN THE
<br /> FACILITIES, AN ACCESSIBLE ROUTE SHALL BE PROVIDED TO ALL FUNCTIONAL ADD 6 INCHES(152 MM)AT EXTERIOR SIDE OF EXTERIOR DOORS. SOLE PROPERTY OF STARBUCKS
<br /> AREAS, INCLUDING RAISED OR SUNKEN AREAS, AND OUTDOOR AREAS. 11B-306.3.2 MAXIMUM DEPTH. KNEE CLEARANCE SHALL EXTEND 25 INCHES (635 CORPORATION, WHICH IS THE OWNER OF THE
<br /> MM) MAXIMUM UNDER AN ELEMENT AT 9 INCHES (229 MM)ABOVE THE FINISH COPYRIGHT IN THIS WORK. THEY SHALL NOT
<br /> 11B-206.2.8 EMPLOYEE WORK AREAS. COMMON USE CIRCULATION PATHS WITHIN FLOOR OR GROUND.
<br /> EMPLOYEE WORK AREAS SHALL COMPLY WITH SECTION 11B-402. 11B-404.2.4 MANEUVERING CLEARANCES. MINIMUM MANEUVERING CLEARANCES BE REPRODUCED (IN WHOLE OR IN PART),
<br /> 11B-306.3.3 MINIMUM REQUIRED DEPTH. WHERE KNEE CLEARANCE IS REQUIRED AT DOORS AND GATES SHALL COMPLY WITH SECTION IIB-404.2.4. MANEUVERING SHARED WITH THIRD PARTIES OR USED IN ANY
<br /> 11B-402.2 COMPONENTS.ACCESSIBLE ROUTES SHALL CONSIST OF ONE OR MORE UNDER AN ELEMENT AS PART OF A CLEAR FLOOR SPACE, THE KNEE CLEARANCE CLEARANCES SHALL EXTEND THE FULL WIDTH OF THE DOORWAY AND THE MANNER ON OTHER PROJECTS OR
<br /> OF THE FOLLOWING COMPONENTS: WALKING SURFACES WITH A RUNNING SLOPE SHALL BE 11 INCHES (279 MM) DEEP MINIMUM AT 9 INCHES (229 MM)ABOVE THE REQUIRED LATCH SIDE OR HINGE SIDE CLEARANCE. EXTENSIONS TO THIS PROJECT WITHOUT THE
<br /> NOT STEEPER THAN 1:20, DOORWAYS, RAMPS, CURB RAMPS EXCLUDING THE FINISH FLOOR OR GROUND, AND 8 INCHES (203 MM) DEEP MINIMUM AT 27 INCHES 11B-404.2.4.1 SWINGING DOORS AND GATES. SWINGING DOORS AND GATES PRIOR WRITTEN CONSENT OF STARBUCKS
<br /> EQ EQ9" NOTE: FLARED SIDES, ELEVATORS,AND PLATFORM LIFTS.ALL COMPONENTS OF AN (686 MM)ABOVE THE FINISH FLOOR OR GROUND. SHALL HAVE MANEUVERING CLEARANCES COMPLYING WITH TABLE IIB-404.2.4.1. CORPORATION. THESE DRAWINGS AND
<br /> ACCESSIBLE ROUTE SHALL COMPLY WITH THE APPLICABLE REQUIREMENTS OF SPECIFICATIONS ARE INTENDED TO EXPRESS
<br /> DOOR-MOUNTED RESTROOM DIVISION 4. 11B-306.3.4 CLEARANCE REDUCTION. BETWEEN 9 INCHES (229 MM)AND 27 INCHES 11B-404.2.7 DOOR AND GATE HARDWARE. HANDLES, PULLS, LATCHES, LOCKS, DESIGN INTENT FOR A PROTOTYPICAL
<br /> SIGNAGE TO COMPLY WITH AND OTHER OPERABLE PARTS ON DOORS AND GATES SHALL COMPLY WITH STARBUCKS STORE (WHICH IS SUBJECT TO
<br /> (686 MM)ABOVE THE FINISH FLOOR OR GROUND, THE KNEE CLEARANCE SHALL BE
<br /> CALIFORNIA TITLE 24 A.D.A. O REDUCE AT A RATE OF 1 INCH (25 MM) IN DEPTH FOR EACH 6 SECTION 11B-309.4. OPERABLE PARTS OF SUCH HARDWARE SHALL BE 34 INCHES CHANGE AT ANYTIME)AND DO NOT REFLECT
<br /> PERMITTED T
<br /> 18 REQUIREMENTS. FLOOR OR GROUND SPACES INCHES ED O IN HEIGHT. (864 MM) MINIMUM AND 44 INCHES (1118 MM) MAXIMUM ABOVE THE FINISH FLOOR ACTUAL SITE CONDITIONS. NEITHER PARTY
<br /> 000 OR GROUND. WHERE SLIDING DOORS ARE IN THE FULLY OPEN POSITION, SHALL HAVE ANY OBLIGATION NOR LIABILITY TO
<br /> GC TO VERIFY COMPLIANCE 11B-302 FLOOR OR GROUND SURFACES 11B-306.3.5 WIDTH. KNEE CLEARANCE SHALL BE 30 INCHES (762 MM)WIDE OPERATING HARDWARE SHALL BE EXPOSED AND USABLE FROM BOTH SIDES. THE OTHER (EXCEPT STATED ABOVE) UNTIL A
<br /> OMINIMUM. WRITTEN AGREEMENT IS FULLY EXECUTED BY ral
<br /> AND PROVIDE ADDITIONAL
<br /> , `GG 11B-302.1 GENERAL. FLOOR AND GROUND SURFACES SHALL BE STABLE, FIRM, AND 11B-404.2.10 DOOR AND GATE SURFACES. SWINGING DOOR AND GATE SURFACES BOTH PARTIES.
<br /> VJ SIGNAGE AS NECESSARY. SLIP RESISTANT AND SHALL COMPLY WITH SECTION IIB-302. WITHIN 10 INCHES (254 MM) OF THE FINISH FLOOR OR GROUND MEASURED
<br /> 5E�� REACH RANGES VERTICALLY SHALL HAVE A SMOOTH SURFACE ON THE PUSH SIDE EXTENDING STARBUCKS TEMPLATE VERSION: i2020-01-31.1
<br /> `_O I INI R 11B-303 CHANGES IN LEVEL THE FULL WIDTH OF THE DOOR OR GATE. PARTS CREATING HORIZONTAL OR
<br /> 11B-308 REACH RANGES VERTICAL JOINTS IN THESE SURFACES SHALL BE WITHIN 1/16 INCH (1.6 MM) OF�PARCHITECT OF RECORD V UNISEX SIGNAGE 11B-303.1 GENERAL. WHERE CHANGES IN LEVEL ARE PERMITTED IN FLOOR OR THE SAME PLANE AS THE OTHER AND BE FREE OF SHARP OR ABRASIVE EDGES. _
<br /> SHOWN, GROUND SURFACES, THEY SHALL COMPLY WITH SECTION 11B-303. 11B-308.1.1 ELECTRICAL SWITCHES. CONTROLS AND SWITCHES INTENDED TO BE CAVITIES CREATED BY ADDED KICK PLATES SHALL BE CAPPED. o a °'
<br /> i>
<br /> G �` DESIGNATED SIGNAGE USED BY THE OCCUPANT OF A ROOM OR AREA TO CONTROL LIGHTING AND > o - •
<br /> V� 11B-303.2 VERTICAL. CHANGES IN LEVEL OFINCH (6.4 MM) HIGH MAXIMUM SHALL RECEPTACLE OUTLETS, APPLIANCES OR COOLING, HEATING AND VENTILATING U_
<br /> '/4
<br /> �.0 V FOR MENS&WOMEN'S BE PERMITTED TO BE VERTICAL AND WITHOUT EDGE TREATMENT. EQUIPMENT, SHALL COMPLY WITH SECTION 11 B-308 EXCEPT THE LOW REACH RAMPS
<br /> - RESTROOMS USED
<br /> CD
<br /> WHEN SHALL BE MEASURED TO THE BOTTOM OF THE OUTLET BOX AND THE HIGH REACH
<br /> 11B-303.3 BEVELED. CHANGES IN LEVEL BETWEEN % INCH (6.4 MM) HIGH MINIMUM SHALL BE MEASURED TO THE TOP OF THE OUTLET BOX. 11B-405.2 SLOPE. RAMP RUNS SHALL HAVE A RUNNING SLOPE NOT STEEPER
<br /> APPLICABLE. AND '/2 INCH (12.7 MM) HIGH MAXIMUM SHALL BE BEVELED WITH A SLOPE NOT THAN 1:12.
<br /> W\E,
<br /> STEEPER THAN 1:2. 11B-308.1.2 ELECTRICAL RECEPTACLE OUTLETS. ELECTRICAL RECEPTACLE mcg architecure
<br /> OUTLETS ON BRANCH CIRCUITS OF 30 AMPERES OR LESS AND COMMUNICATION 11B-405.4 FLOOR OR GROUND SURFACES. FLOOR OR GROUND SURFACES OF 15635 Alton Parkway, Suite 100, Irvine,CA 92618
<br /> 11B-304 TURNING SPACE SYSTEM RECEPTACLES SHALL COMPLY WITH SECTION 11B-308 EXCEPT THE LOW RAMP RUNS SHALL COMPLY WITH SECTION IIB-302. CHANGES IN LEVEL OTHER P: 949.553.1117 F: 949.474.7056
<br /> REACH SHALL BE MEASURED TO THE BOTTOM OF THE OUTLET BOX AND THE HIGH THAN THE RUNNING SLOPE AND CROSS SLOPE ARE NOT PERMITTED ON RAMP
<br /> 11B-304.3 SIZE. TURNING SPACE SHALL COMPLY WITH SECTION 11B-304.3.1 OR REACH SHALL BE MEASURED TO THE TOP OF THE OUTLET BOX. RUNS. ARCHITECT STAMP
<br /> I IB-304.3.2.
<br /> 11B-308.2 FORWARD REACH. 11B-405.5 CLEAR WIDTH. THE CLEAR WIDTH OF A RAMP RUN SHALL BE 48 INCHES SED A c
<br /> CIRCULAR
<br /> RR DOOR SIGNAGE NCHES (1524MM) DIAMETER SPACE
<br /> ER MINIMUM THE SPACESHAL SHALLBE A SPACE OF 60 (1219 MM)) PERMITTED TO 11B-308.2.1 UNOBSTRUCTED. WHERE A FORWARD REACH IS UNOBSTRUCTED, THE 11B-405.6 RISE. PGE�NIN� �
<br /> HE RISE FOR ANY RAMP RUN SHALL BE 30 INCHES (762 MM) GUM. ��
<br /> 15 INCLUDE KNEE AND TOE CLEARANCE COMPLYING WITH SECTION IIB-306. HIGH FORWARD REACH SHALL BE 48 INCHES (1219 MM) MAXIMUM AND THE LOW MAXIMUM. A
<br /> Scale: 1/2"=1'=0" ELEVATION FORWARD REACH SHALL BE 15 INCHES (381 MM) MINIMUM ABOVE THE FINISH - 1839
<br /> 11B-304.3.2 T-SHAPED SPACE. THE TURNING SPACE SHALL BE A T-SHAPED SPACE FLOOR OR GROUND. 11B-405.7 LANDINGS. RAMPS SHALL HAVE LANDINGS AT THE TOP AND THE g� 1
<br /> WITHIN A 60 INCH (1524 MM)SQUARE MINIMUM WITH ARMS AND BASE 36 INCHES BOTTOM OF EACH RAMP RUN. LANDINGS SHALL COMPLY WITH SECTION IIB-405.7.
<br /> NOTE: (914 MM)WIDE MINIMUM. EACH ARM OF THE T SHALL BE CLEAR OF OBSTRUCTIONS 11B-308.2.2 OBSTRUCTED HIGH REACH. WHERE A HIGH FORWARD REACH IS OVER 9� tiP
<br /> WALL MOUNTED SIGNAGE TO BE LOCATED ON 12 INCHES (305 MM) MINIMUM IN EACH DIRECTION AND THE BASE SHALL BE CLEAR AN OBSTRUCTION, THE CLEAR FLOOR SPACE SHALL EXTEND BENEATH THE F CAI_1 O-o �
<br /> LATCH SIDE OF DOOR CLEAR OF DOOR-SWING. OF OBSTRUCTIONS 24 INCHES (610 MM) MINIMUM. THE SPACE SHALL BE PERMITTED ELEMENT FOR A DISTANCE NOT LESS THAN THE REQUIRED REACH DEPTH OVER CURB RAMPS
<br /> MOUNT AT 60" MAX TO BASELINE OF THE HIGHEST TO INCLUDE KNEE AND TOE CLEARANCE COMPLYING WITH SECTION 11B-306 ONLY THE OBSTRUCTION. THE HIGH FORWARD REACH SHALL BE 48 INCHES (1219 MM)
<br /> LINE OF RAISED CHARACTERS PER 11 B-703. AT THE END OF EITHER THE BASE OR ONE ARM. MAXIMUM WHERE THE REACH DEPTH IS 20 INCHES (508 MM) MAXIMUM. WHERE 11B-406.2 PERPENDICULAR CURB RAMPS. PERPENDICULAR CURB RAMPS SHALL
<br /> THE REACH DEPTH EXCEEDS 20 INCHES (508 MM), THE HIGH FORWARD REACH COMPLY WITH SECTIONS 11B-406.2 AND 11B-406.5.
<br /> 11B-305.7 MANEUVERING CLEARANCE. WHERE A CLEAR FLOOR OR GROUND SHALL BE 44 INCHES (1118 MM) MAXIMUM AND THE REACH DEPTH SHALL BE 25
<br /> LETTERING RAISED 1/32" LL GENDER SPACE IS LOCATED IN AN ALCOVE OR OTHERWISE CONFINED ON ALL OR PART OF INCHES (635 MM) MAXIMUM. 11B-406.2.1 SLOPE. RAMP RUNS SHALL HAVE A RUNNING SLOPE NOT STEEPER
<br /> THREE SIDES, ADDITIONAL MANEUVERING CLEARANCE SHALL BE PROVIDED IN THAN 1:12.
<br /> ACCORDANCE WITH SECTIONS 11B-305.7.1 AND 11B-305.7.2. 11B-308.3 SIDE REACH.
<br /> HEIGHT OF LETTERING 5/8" RESTROOM 11B-406.2.2 SIDES OF CURB RAMPS. WHERE PROVIDED, CURB RAMP FLARES
<br /> MIN. TO 2" MAX. 11B-305.7.1 FORWARD APPROACH.ALCOVES SHALL BE 36 INCHES (914 MM)WIDE 11B-308.3.1 UNOBSTRUCTED. WHERE A CLEAR FLOOR OR GROUND SPACE SHALL NOT BE STEEPER THAN 1:10.
<br /> ��Q MINIMUM WHERE THE DEPTH EXCEEDS 24 INCHES (610 MM). ALLOWS A PARALLEL APPROACH TO AN ELEMENT AND THE SIDE REACH IS
<br /> ` CORRESPONDING GRADE II BRAILLE. PER UNOBSTRUCTED, THE HIGH SIDE REACH SHALL BE 48 INCHES (1219 MM) MAXIMUM 11B-406.3 PARALLEL CURB RAMPS. PARALLEL CURB RAMPS SHALL COMPLY WITH
<br /> O� V CBC 11 B-703.3.2 BRAILLE SHALL BE FLUSH 11B-305.7.2 PARALLEL APPROACH.ALCOVES SHALL BE 60 INCHES (1524 MM)WIDE AND THE LOW SIDE REACH SHALL BE 15 INCHES (381 MM) MINIMUM ABOVE THE SECTIONS 11 B-406.3 AND 11 B-406.5.
<br /> U) A` LEFT OR CENTERED AND PLACED A MIN. OF MINIMUM WHERE THE DEPTH EXCEEDS 15 INCHES (381 MM). FINISH FLOOR OR GROUND. Q
<br /> `v 3/8" INCH AND MAXIMUM OF 1/2 INCH BELOW Q 11B-406.3.1 SLOPE. THE RUNNING SLOPE OF THE CURB RAMP SEGMENTS SHALL
<br /> RAISED CHARACTERS OR SYMBOLS 11B-305 CLEAR FLOOR OR GROUND SPACE 11B-308.3.2 OBSTRUCTED HIGH REACH. WHERE A CLEAR FLOOR OR GROUND BE IN-LINE WITH THE DIRECTION OF SIDEWALK TRAVEL. RAMP RUNS SHALL HAVE
<br /> ` " 0 ? SPACE ALLOWS A PARALLEL APPROACH TO AN ELEMENT AND THE HIGH SIDE A RUNNING SLOPE NOT STEEPER THAN 1:12. = W
<br /> N 11B-305.2 FLOOR OR GROUND SURFACES. FLOOR OR GROUND SURFACES OF A REACH IS OVER AN OBSTRUCTION, THE HEIGHT OF THE OBSTRUCTION SHALL BE
<br /> UI �`\`O`" co CLEAR FLOOR OR GROUND SPACE SHALL COMPLY WITH SECTION 11B-302. 34 INCHES (864 MM) MAXIMUM AND THE DEPTH OF THE OBSTRUCTION SHALL BE 24 11B-406.3.2 TURNING SPACE.A TURNING SPACE 48 INCHES (1219 MM) MINIMUM BY Q
<br /> .( CHANGES IN LEVEL ARE NOT PERMITTED. INCHES (610 MM) MAXIMUM. THE HIGH SIDE REACH SHALL BE 48 INCHES (1219 MM) 48 INCHES (1219 MM) MINIMUM SHALL BE PROVIDED AT THE BOTTOM OF THE CURB 06 C'4
<br /> m `�` MAXIMUM FOR A REACH DEPTH OF 10 INCHES (254 MM) MAXIMUM. WHERE THE RAMP. THE SLOPE OF THE TURNING SPACE IN ALL DIRECTIONS SHALL BE 1:48 ~ LO
<br /> 06 `'P FINISHED FLOOR EXCEPTION: SLOPES NOT STEEPER THAN 1:48 SHALL BE PERMITTED. REACH DEPTH EXCEEDS 10 INCHES (254 MM), THE HIGH SIDE REACH SHALL BE 46 MAXIMUM. W z CY)
<br /> INCHES (1168 MM) MAXIMUM FOR A REACH DEPTH OF 24 INCHES (610 MM) J O Q
<br /> 11B-305.3 SIZE. THE CLEAR FLOOR OR GROUND SPACE SHALL BE 30 INCHES (762 MAXIMUM. 11B-406.5 COMMON REQUIREMENTS. CURB RAMPS AND BLENDED TRANSITIONS LU ! ,
<br /> �.
<br /> W\E,
<br /> MM) MINIMUM BY 48 INCHES (1219 MM) MINIMUM. SHALL COMPLY WITH SECTION 11 B-406.5. W LLL U
<br /> 11B-309 OPERABLE PARTS p
<br /> FU 11B-305.4 KNEE AND TOE CLEARANCE. UNLESS OTHERWISE SPECIFIED, CLEAR Z Q Q
<br /> pl ACCESSIBLE I D WALL SYMBOLS FLOEAORANCR OR COMPLYINGNDSPA CE WITSHALL BE H SECTION RMI TED TO INCLUDE KNEE AND TOE 11B-309.1 GENERAL. OPERABLE PARTS SHALL COMPLY WITH SECTION IIB-309. z T � Q
<br /> m 11B-309.2 CLEAR FLOOR SPACE.A CLEAR FLOOR OR GROUND SPACE COMPLYING U y U O Q
<br /> 141Scale: 1 1/2" = V-0" LIJ LU CO
<br /> X 11B-305.5 POSITION. UNLESS OTHERWISE SPECIFIED, CLEAR FLOOR OR GROUND WITH SECTION 11B-305 SHALL BE PROVIDED. O O 00 O
<br /> OO �O OO OOcl�
<br /> m SPACE SHALL BE POSITIONED FOR EITHER FORWARD OR PARALLEL APPROACH TO 0 0 (=)
<br /> U)I AN ELEMENT. 11B-309.3 HEIGHT. OPERABLE PARTS SHALL BE PLACED WITHIN ONE OR MORE OF W 0-
<br /> m THE REACH RANGES SPECIFIED IN SECTION IIB-308.
<br /> O
<br /> O CBC 1010.1.1 - DOOR SIZE 11B-305.6 APPROACH. ONE FULL UNOBSTRUCTED SIDE OF THE CLEAR FLOOR OR
<br /> O GROUND SPACE SHALL ADJOIN AN ACCESSIBLE ROUTE OR ADJOIN ANOTHER 11B-309.4 OPERATION. OPERABLE PARTS SHALL BE OPERABLE WITH ONE HAND O O - STORE #: 65246
<br /> N T-0" DOOR WIDTH CLEAR FLOOR OR GROUND SPACE. AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE
<br /> 4 6'-8" HEIGHT WRIST. THE FORCE REQUIRED TO ACTIVATE OPERABLE PARTS SHALL BE 5 PROJECT #: 88584-001
<br /> 32" CLEAR WIDTH11B-305.7 MANEUVERING CLEARANCE. WHERE A CLEAR FLOOR OR GROUND POUNDS (22.2 N) MAXIMUM. O OO OO OO ISSUE DATE: 50% CD 1-29-21
<br /> Ln
<br /> E CBC 11 B-404.2.9- DOOR OPENING FORCE SPACE IS LOCATED IN AN ALCOVE OR OTHERWISE CONFINED ON ALL OR PART OF N DESIGN MANAGER: J. RAMOS
<br /> TYPE OF HARDWARE: PUSH/PULL THREE SIDES, ADDITIONAL MANEUVERING CLEARANCE SHALL BE PROVIDED IN DOORS AND DOORWAYS O O O OO PRODUCTION DESIGNER:
<br /> O0 ACCORDANCE WITH SECTIONS IIB-305.7.1 AND 11B-305.7.2.
<br /> p MAX. EFFORT FOR EXT. DOORS = 5 LBS CHECKED BY: SKIM
<br /> E MAX. EFFORT FOR INT. DOORS = 5 LBS. 12" DIA 1'-0" 1'-0" 11B-305.7.1 FORWARD APPROACH.ALCOVES SHALL BE 36 INCHES (914 MM)WIDE 11B-404.2 MANUAL DOORS, DOORWAYS,AND MANUAL GATES. MANUAL DOORS
<br /> REQUIRED FIRE DOORS, MAX. EFFORT = 15 LBS. AND DOORWAYS AND MANUAL GATES INTENDED FOR USER PASSAGE SHALL 0.45"AT TOP TYPICAL PLAN
<br /> INTERIOR WOMEN MINIMUM WHERE THE DEPTH EXCEEDS 24 INCHES (610 MM). COMPLY WITH SECTION IIB-404.2. 90"AT BASE
<br /> UNISEX SIGNAGE IS FOR ALL 2.35" Revision Schedule
<br /> CBC 11B-404.2.10- SMOOTH SURFACE MEN SINGLE ACCOMMODATION 11B-305.7.2 PARALLEL APPROACH.ALCOVES SHALL BE 60 INCHES (1524 MM)WIDE
<br /> SANITARY FACILITIES IDENTIFICATION SYMBOLS RESTROOMS MINIMUM WHERE THE DEPTH EXCEEDS 15 INCHES (381 MM). 11B-404.2.2 DOUBLE-LEAF DOORS AND GATES.AT LEAST ONE OF THE ACTIVE Rev Date By Description
<br /> 10" KICKPLATE OR SMOOTH LEAVES OF DOORWAYS WITH TWO LEAVES SHALL COMPLY WITH SECTIONS
<br /> 2 MEN'S: AN EQUILATERAL TRIANGLE WITH EDGES 12" LONG AND A VERTEXGR
<br /> LU OUT BED.
<br /> . . 11B-404.2.4.
<br /> FULL WIDTH OF DOOR 11B-40423 AND
<br /> U POINTING UPWARD. (11 B-703.7.2.6.1) 11B-306 KNEE AND TOE CLEARANCE = JOINT COLOR TO MATCH TILES.
<br /> 2 - 11B-404.2.3 CLEAR WIDTH. DOOR OPENINGS SHALL PROVIDE A CLEAR WIDTH OF o
<br /> W CBC 11 B-404.2.5-THRESHOLDS WOMEN'S: A CIRCLE, 12" IN DIAMETER. (11 B-703.7.2.6.2) 11B-306.1 GENERAL. WHERE SPACE BENEATH AN ELEMENT IS INCLUDED AS PART 32 INCHES (813 MM) MINIMUM. CLEAR OPENINGS OF DOORWAYS WITH SWINGING N RECESS CONC. PER MFR.
<br /> Of OF CLEAR FLOOR OR GROUND SPACE OR TURNING SPACE, THE SPACE SHALL DOORS SHALL BE MEASURED BETWEEN THE FACE OF THE DOOR AND THE RECOMMENDATIONS. TYPICAL SECTION A
<br /> Q 1/2" MAX. THRESHOLD WITH 1/4" BEVEL UNISEX: A CIRCLE SYMBOL 12" DIAMETER WITH AN EQUILATERAL TRIANGLE COMPLY WITH SECTION 118-306. ADDITIONAL SPACE SHALL NOT BE PROHIBITED
<br /> M 1:48 MAX. SLOPE STOP, WITH THE DOOR OPEN 90 DEGREES. OPENINGS MORE THAN 24 INCHES
<br /> Q p SUPERIMPOSED ON AND GEOMETRICALLY INSCRIBED WITHIN THE 12" BENEATH AN ELEMENT BUT SHALL NOT BE CONSIDERED AS PART OF THE CLEAR NOTE: SHEET TITLE:
<br /> 00 DIAMETER. (11B-703.7.2.6.3) FLOOR OR GROUND SPACE OR TURNING SPACE. (610 MM) DEEP SHALL PROVIDE A CLEAR OPENING OF 36 INCHES (914 MM) 1. DETECTABLE WARNING SHALL BE OF CONTRASTING COLOR WITH
<br /> LO Q MINIMUM. THERE SHALL BE NO PROJECTIONS INTO THE REQUIRED CLEAR ADJACENT ACCESSIBILITY NOTES
<br /> e� EXTERIOR IDENTIFICATION SYMBOLS SHALL BE 1/4"THICK AND OF CONTRASTING COLOR 11B-306.2 TOE CLEARANCE. OPENING WIDTH LOWER THAN 34 INCHES (864 MM)ABOVE THE FINISH FLOOR SURFACE: LIGHT-ON-DARK OR DARK-ON-LIGHT. MATERIAL SHALL BE
<br /> OR GROUND. PROJECTIONS INTO THE CLEAR OPENING WIDTH BETWEEN 34
<br /> p WITH THE COLOR OF THE DOOR OR SURFACE MOUNTED UPON. SYMBOLS INTEGRAL PART OF THE WALKING SURFACE.
<br /> INCHES (864 MM)AND 80 INCHES (2032 MM)ABOVE THE FINISH FLOOR OR
<br /> SHALL BE MOUNTED ON THE DOOR AT A HEIGHT OF +60"AFF TO THE 11B-306.2.1 GENERAL. SPACE UNDER AN ELEMENT BETWEEN THE FINISH FLOOR OR GROUND SHALL NOT EXCEED 4 INCHES (102 MM). 2. TRUNCATED DOMES TO BE: "INTERLOCK SAN DIEGO"TACTILE STONE, SCALE: AS SHOWN
<br /> N SECTION @ ENTRY DOOR CENTERLINE OF SIGN. GROUND AND 9 INCHES (229 MM)ABOVE THE FINISH FLOOR OR GROUND SHALL BE CARLSBAD, CALIFORNIA(760)434-5566 OR APPROVED EQUAL.
<br /> ADA COMPIANCE DETAIL ACCESSIBLE ID DOOR SYMBOLS CONSIDERED TOE CLEARANCE AND SHALL COMPLY WITH SECTION 118-306.2. TRUNCATED DOMES SHEET NUMBER:
<br /> N1 Scae:N.T.S scale: 1 1/2" = V-0" 1 scale: 6" = 1'-0" G004
<br /> N
<br />
|