|
ACCESSIBILITY NOTES (CONT. )
<br /> CURB RAMPS (CONT.) PARKING CONT. LAVATORIES CONT.
<br /> 11B-406.5.1 LOCATION. CURB RAMPS AND THE FLARED SIDES OF CURB RAMPS "UNAUTHORIZED VEHICLES PARKED IN DESIGNATED ACCESSIBLE SPACES NOT 11B-606.5 EXPOSED PIPES AND SURFACES. WATER SUPPLY AND DRAIN PIPES �r
<br /> SHALL BE LOCATED SO THAT THEY DO NOT PROJECT INTO VEHICULAR TRAFFIC DISPLAYING DISTINGUISHING PLACARDS OR SPECIAL LICENSE PLATES ISSUED UNDER LAVATORIES AND SINKS SHALL BE INSULATED OR OTHERWISE
<br /> LANES, PARKING SPACES, OR PARKING ACCESS AISLES. CURB RAMPS AT MARKED FOR PERSONS WITH DISABILITIES WILL BE TOWED AWAY AT THE OWNER'S CONFIGURED TO PROTECT AGAINST CONTACT. THERE SHALL BE NO SHARP OR
<br /> CROSSINGS SHALL BE WHOLLY CONTAINED WITHIN THE MARKINGS, EXCLUDING EXPENSE. TOWED VEHICLES MAY BE RECLAIMED AT: ABRASIVE SURFACES UNDER LAVATORIES AND SINKS.
<br /> ANY FLARED SIDES. OR BY TELEPHONING
<br /> 11B-606.6 ADJACENT SIDE WALL OR PARTITION. LAVATORIES, WHEN LOCATED
<br /> 11B-406.5.2 WIDTH. THE CLEAR WIDTH OF CURB RAMP RUNS (EXCLUDING ANY BLANK SPACES SHALL BE FILLED IN WITH APPROPRIATE INFORMATION AS A ADJACENT TO A SIDE WALL OR PARTITION, SHALL BEA MINIMUM OF 18 INCHES
<br /> FLARED SIDES), BLENDED TRANSITIONS, AND TURNING SPACES SHALL BE 48 PERMANENT PART OF THE SIGN. (457 MM) TO THE CENTERLINE OF THE FIXTURE.
<br /> INCHES (1219 MM) MINIMUM.
<br /> 11B-606.7 SINK DEPTH. SINKS SHALL BE 6%INCHES (165 MM) DEEP MAXIMUM. ©2020 STARBUCKS COFFEE COMPANY
<br /> 11B-406.5.3 LANDINGS. LANDINGS SHALL BE PROVIDED AT THE TOPS OF CURB TOILET ROOMS
<br /> RAMPS AND BLENDED TRANSITIONS. THE LANDING CLEAR LENGTH SHALL BE 48 11B-603 TOILET AND BATHING ROOMS SIGNS STARBUCKS'
<br /> INCHES (1219 MM) MINIMUM. THE LANDING CLEAR WIDTH SHALL BE AT LEAST AS
<br /> WIDE AS THE CURB RAMP, EXCLUDING ANY FLARED SIDES, OR THE BLENDED 11B-603.2 CLEARANCES. CLEARANCES SHALL COMPLY WITH SECTION 11B-603.2. 11B-703 SIGNS 2401 UTAH AVENUE SOUTH
<br /> TRANSITION LEADING TO THE LANDING. THE SLOPE OF THE LANDING IN ALL SEATTLE, WASHINGTON 98134
<br /> DIRECTIONS SHALL BE 1:48 MAXIMUM. 11B-603.2.1 TURNING SPACE. TURNING SPACE COMPLYING WITH SECTION 11B-703.2 RAISED CHARACTERS. RAISED CHARACTERS SHALL COMPLY WITH (206) 318-1575
<br /> 11B-304 SHALL BE PROVIDED WITHIN THE ROOM. SECTION IIB-703.2 AND SHALL BE DUPLICATED IN BRAILLE COMPLYING WITH
<br /> 11B-406.5.11 GROOVED BORDER. CURB RAMPS SHALL HAVE A GROOVED BORDER SECTION I IB-703.3. RAISED CHARACTERS SHALL BE INSTALLED IN ACCORDANCE
<br /> 12 INCHES (305 MM)WIDE ALONG THE TOP OF THE CURB RAMP AT THE LEVEL 11B-603.2.2 OVERLAP. REQUIRED CLEAR FLOOR SPACES, CLEARANCE AT WITH SECTION 11B-703.4. THESE DRAWINGS AND THE PROJECT MANUAL
<br /> SURFACE OF THE TOP LANDING AND AT THE OUTSIDE EDGES OF THE FLARED FIXTURES, AND TURNING SPACE SHALL BE PERMITTED TO OVERLAP. ARE CONFIDENTIAL AND SHALL REMAIN THE
<br /> /4
<br /> SIDES. THE GROOVED BORDER SHALL CONSIST OF A SERIES OF GROOVES ' INCH 11B-703.2.1 DEPTH. RAISED CHARACTERS SHALL BE 1/32 INCH (0.8 MM) MINIMUM SOLE PROPERTY OF STARBUCKS
<br /> (6.4 MM)WIDE BY'/4 INCH (6.4 MM) DEEP, AT 3/4 INCH (19 MM)ON CENTER. 11B-603.2.3 DOOR SWING. DOORS SHALL NOT SWING INTO THE CLEAR FLOOR ABOVE THEIR BACKGROUND. CORPORATION, WHICH IS THE OWNER OF THE
<br /> SPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE. OTHER THAN THE DOOR COPYRIGHT IN THIS WORK. THEY SHALL NOT
<br /> 11B-406.5.12 DETECTABLE WARNINGS. CURB RAMPS AND BLENDED TRANSITIONS TO THE ACCESSIBLE WATER CLOSET COMPARTMENT,A DOOR, IN ANY 11B-703.2.2 CASE. CHARACTERS SHALL BE UPPERCASE. BE REPRODUCED (IN WHOLE OR IN PART),
<br /> SHALL HAVE DETECTABLE WARNINGS COMPLYING WITH SECTION 11 B-705. POSITION, MAY ENCROACH INTO THE TURNING SPACE BY 12 INCHES (305 MM) SHARED WITH THIRD PARTIES OR USED IN ANY
<br /> MAXIMUM. 11B-703.2.3 STYLE. CHARACTERS SHALL BE SANS SERIF. CHARACTERS SHALL MANNER ON OTHER PROJECTS OR
<br /> NOT BE ITALIC, OBLIQUE, SCRIPT, HIGHLY DECORATIVE, OR OF OTHER UNUSUAL EXTENSIONS TO THIS PROJECT WITHOUT THE
<br /> PARKING SPACES 11B-603.3 MIRRORS. MIRRORS LOCATED ABOVE LAVATORIES OR FORMS. PRIOR WRITTEN CONSENT OF STARBUCKS
<br /> 11B-502 PARKING SPACES COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE CORPORATION. THESE DRAWINGS AND
<br /> REFLECTING SURFACE 40 INCHES (1016 MM) MAXIMUM ABOVE THE FINISH 11B-703.2.4 CHARACTER PROPORTIONS. CHARACTERS SHALL BE SELECTED SPECIFICATIONS ARE INTENDED TO EXPRESS
<br /> 11B-502.1 GENERAL. CAR AND VAN PARKING SPACES SHALL COMPLY WITH FLOOR OR GROUND. MIRRORS NOT LOCATED ABOVE LAVATORIES OR FROM FONTS WHERE THE WIDTH OF THE UPPERCASE LETTER "O" IS 60 PERCENT DESIGN INTENT FOR A PROTOTYPICAL
<br /> COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE MINIMUM AND 110 PERCENT MAXIMUM OF THE HEIGHT OF THE UPPERCASE STARBUCKS STORE (WHICH IS SUBJECT TO
<br /> SECTION 2. WHERE PARKING SPACES ARE MARKED WITH LINES, WIDTH REFLECTING SURFACE 35 INCHES (889 MM) MAXIMUM ABOVE THE FINISH FLOOR LETTER"I" CHANGE AT ANYTIME)AND DO NOT REFLECT
<br /> MEASUREMENTS OF PARKING SPACES AND ACCESS AISLES SHALL BE MADE . ACTUAL SITE CONDITIONS. NEITHER PARTY
<br /> FROM THE CENTERLINE OF THE MARKINGS. OR GROUND. SHALL HAVE ANY OBLIGATION NOR LIABILITY TO
<br /> 11B-703.2.5 CHARACTER HEIGHT. CHARACTER HEIGHT MEASURED VERTICALLY THE OTHER (EXCEPT STATED ABOVE) UNTIL A
<br /> 11B-502.2 VEHICLE SPACES. CAR AND VAN PARKING SPACES SHALL BE 216 INCHES 11B-603.5 ACCESSORIES. WHERE TOWEL OR SANITARY NAPKIN DISPENSERS, FROM THE BASELINE OF THE CHARACTER SHALL BE 5/8 INCH (15.9 MM) MINIMUM WRITTEN AGREEMENT IS FULLY EXECUTED BY
<br /> (5486 MM) LONG MINIMUM. CAR PARKING SPACES SHALL BE 108 INCHES (2743 MM) WASTE RECEPTACLES, OR OTHER ACCESSORIES ARE PROVIDED IN TOILET AND 2 INCHES (51 MM) MAXIMUM BASED ON THE HEIGHT OF THE UPPERCASE BOTH PARTIES.
<br /> WIDE MINIMUM AND VAN PARKING SPACES SHALL BE 144 INCHES (3658 MM) WIDE FACILITIES, AT LEAST ONE OF EACH TYPE SHALL BE LOCATED ON AN LETTER"I".
<br /> MINIMUM, SHALL BE MARKED TO DEFINE THE WIDTH, AND SHALL HAVE AN ACCESSIBLE ROUTE. ALL OPERABLE PARTS, INCLUDING COIN SLOTS, SHALL BE 11B-703.2.6 STROKE THICKNESS. STROKE THICKNESS OF THE UPPERCASE STARBUCKS TEMPLATE VERSION: i2020-01-31.1
<br /> ADJACENT ACCESS AISLE COMPLYING WITH SECTION I IB-502.3. 40 INCHES (1016 MM) MAXIMUM ABOVE THE FINISH FLOOR. LETTER"I" SHALL BE 15 PERCENT MAXIMUM OF THE HEIGHT OF THE CHARACTER.
<br /> 11B-502.3 ACCESS AISLE.ACCESS AISLES SERVING PARKING SPACES SHALL 11B-703.2.7 CHARACTER SPACING. CHARACTER SPACING SHALL BE MEASURED ARCHITECT OF RECORD
<br /> COMPLY WITH SECTION I IB-502.3. ACCESS AISLES SHALL ADJOIN AN ACCESSIBLE WATER CLOSETS BETWEEN THE TWO CLOSEST POINTS OF ADJACENT RAISED CHARACTERS
<br /> ROUTE. TWO PARKING SPACES SHALL BE PERMITTED TO SHARE A COMMON WITHIN A MESSAGE, EXCLUDING WORD SPACES. WHERE CHARACTERS HAVEN _ i>
<br /> 11B-604 WATER CLOSETS " > °' - 0110 ACCESS AISLE. RECTANGULAR CROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISED
<br /> CHARACTERS SHALL BE 1/8 INCH (3.2 MM) MINIMUM AND 4 TIMES THE RAISED " "
<br /> 11B-502.3.2 LENGTH.ACCESS AISLES SHALL EXTEND THE FULL REQUIRED LENGTH 11B-604.2 LOCATION. THE WATER CLOSET SHALL BE POSITIONED WITH A WALL CHARACTER STROKE WIDTH MAXIMUM. WHERE CHARACTERS HAVE OTHER cn
<br /> OF THE PARKING SPACES THEY SERVE. OR PARTITION TO THE REAR AND TO ONE SIDE. THE CENTERLINE OF THE WATER CROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISED CHARACTERS SHALL
<br /> CLOSET SHALL BE 17 INCHES (432 MM) MINIMUM TO 18 INCHES (457 MM) BE 1/16 INCH (1.6 MM) MINIMUM AND 4 TIMES THE RAISED CHARACTER STROKE
<br /> 11B-502.3.3 MARKING. ACCESS AISLES SHALL BE MARKED WITH A BLUE PAINTED MAXIMUM FROM THE SIDE WALL OR PARTITION, EXCEPT THAT THE WATER WIDTH MAXIMUM AT THE BASE OF THE CROSS SECTIONS, AND 1/8 INCH (3.2 MM) m c g a r c h i t e c u r e
<br /> BORDERLINE AROUND THEIR PERIMETER. THE AREA WITHIN THE BLUE CLOSET SHALL BE 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) MINIMUM AND 4 TIMES THE RAISED CHARACTER STROKE WIDTH MAXIMUM AT THE 15635 Alton Parkway, Suite 100, Irvine,CA 92618
<br /> BORDERLINES SHALL BE MARKED WITH HATCHED LINES A MAXIMUM OF 36 INCHES MAXIMUM FROM THE SIDE WALL OR PARTITION IN THE AMBULATORY ACCESSIBLE TOP OF THE CROSS SECTIONS. CHARACTERS SHALL BE SEPARATED FROM P: 949.553.1117 F: 949.474.7056
<br /> (914 MM)ON CENTER IN A COLOR CONTRASTING WITH THAT OF THE AISLE TOILET COMPARTMENT SPECIFIED IN SECTION 11B-604.8.2. WATER CLOSETS RAISED BORDERS AND DECORATIVE ELEMENTS 3/8 INCH (9.5 MM) MINIMUM.
<br /> SURFACE, PREFERABLY BLUE OR WHITE. THE WORDS "NO PARKING" SHALL BE SHALL BE ARRANGED FOR A LEFT-HAND OR RIGHT-HAND APPROACH.
<br /> PAINTED ON THE SURFACE WITHIN EACH ACCESS AISLE IN WHITE LETTERS A 11B-703.2.8 LINE SPACING. SPACING BETWEEN THE BASELINES OF SEPARATE ARCHITECT STAMP
<br /> MINIMUM OF 12 INCHES (305 MM) IN HEIGHT AND LOCATED TO BE VISIBLE FROM 11B-604.3 CLEARANCE. CLEARANCES AROUND WATER CLOSETS AND IN TOILET LINES OF RAISED CHARACTERS WITHIN A MESSAGE SHALL BE 135 PERCENT D A
<br /> THE ADJACENT VEHICULAR WAY. ACCESS AISLE MARKINGS MAY EXTEND BEYOND COMPARTMENTS SHALL COMPLY WITH SECTION IIB-604.3. MINIMUM AND 170 PERCENT MAXIMUM OF THE RAISED CHARACTER HEIGHT. IgE
<br /> THE MINIMUM REQUIRED LENGTH. V� PGE WIN�IC�`/�`
<br /> 11B-604.3.1 SIZE. CLEARANCE AROUND A WATER CLOSET SHALL BE 60 INCHES 11B-703.4 INSTALLATION HEIGHT AND LOCATION. SIGNS WITH TACTILE 'A n
<br /> 11B-502.3.4 LOCATION.ACCESS AISLES SHALL NOT OVERLAP THE VEHICULAR (1524 MM) MINIMUM MEASURED PERPENDICULAR FROM THE SIDE WALL AND 56 CHARACTERS SHALL COMPLY WITH SECTION 11B-703.4. - _
<br /> WAY.ACCESS AISLES SHALL BE PERMITTED TO BE PLACED ON EITHER SIDE OF INCHES (1422 MM) MINIMUM MEASURED PERPENDICULAR FROM THE REAR WALL. - 1839
<br /> THE PARKING SPACE EXCEPT FOR VAN PARKING SPACES WHICH SHALL HAVE A MINIMUM 60 INCHES (1524 MM) WIDE AND 48 INCHES (1219 MM) DEEP 11B-703.4.1 HEIGHT ABOVE FINISH FLOOR OR GROUND. TACTILE CHARACTERS 9/ 1
<br /> MANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET. ON SIGNS SHALL BE LOCATED 48 INCHES 1219 MM MINIMUM ABOVE THE FINISH
<br /> ACCESS AISLES LOCATED ON THE PASSENGER SIDE OF THE PARKING SPACES. ( ) ` y
<br /> FLOOR OR GROUND SURFACE, MEASURED FROM THE BASELINE OF THE LOWEST
<br /> 11B-604.3.2 OVERLAP.THE REQUIRED CLEARANCE AROUND THE WATER CLOSET BRAILLE CELLS AND 60 INCHES 1524 MM MAXIMUM ABOVE THE FINISH FLOOR OR F CAI_1 O
<br /> 11B-502.4 FLOOR OR GROUND SURFACES. PARKING SPACES AND ACCESS AISLES SHALL BE PERMITTED TO OVERLAP THE WATER CLOSET, ASSOCIATED GRAB ( )
<br /> -
<br /> SERVING THEM SHALL COMPLY WITH SECTION IIB-302. ACCESS AISLES SHALL BE GROUND SURFACE, MEASURED FROM THE BASELINE OF THE HIGHEST LINE OF
<br /> AT THE SAME LEVEL AS THE PARKING SPACES THEY SERVE. CHANGES IN LEVEL BARS, DISPENSERS, SANITARY NAPKIN DISPOSAL UNITS, COAT HOOKS, SHELVES, RAISED CHARACTERS.
<br /> ARE NOT PERMITTED. ACCESSIBLE ROUTES, CLEAR FLOOR SPACE AND CLEARANCES REQUIRED AT
<br /> OTHER FIXTURES, AND THE TURNING SPACE. NO OTHER FIXTURES OR 11B-703.4.2 LOCATION.WHERE A TACTILE SIGN IS PROVIDED AT A DOOR, THE
<br /> 11B-502.5 VERTICAL CLEARANCE. PARKING SPACES, ACCESS AISLES AND OBSTRUCTIONS SHALL BE LOCATED WITHIN THE REQUIRED WATER CLOSET SIGN SHALL BE LOCATED ALONGSIDE THE DOOR AT THE LATCH SIDE. WHERE A
<br /> VEHICULAR ROUTES SERVING THEM SHALL PROVIDE A VERTICAL CLEARANCE OF CLEARANCE. TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGN
<br /> 98 INCHES (2489 MM) MINIMUM. SHALL BE LOCATED ON THE INACTIVE LEAF. WHERE A TACTILE SIGN IS PROVIDED
<br /> 11B-604.4 SEATS. THE SEAT HEIGHT OF A WATER CLOSET ABOVE THE FINISH AT DOUBLE DOORS WITH TWO ACTIVE LEAFS, THE SIGN SHALL BE LOCATED TO
<br /> 11B-502.6 IDENTIFICATION. PARKING SPACE IDENTIFICATION SIGNS SHALL INCLUDE FLOOR SHALL BE 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) THE RIGHT OF THE RIGHT HAND DOOR. WHERE THERE IS NO WALL SPACE AT THE
<br /> THE INTERNATIONAL SYMBOL OF ACCESSIBILITY COMPLYING WITH SECTION MAXIMUM MEASURED TO THE TOP OF THE SEAT. SEATS SHALL NOT BE SPRUNG LATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT SIDE OF DOUBLE DOORS,
<br /> > TO RETURN TO A LIFTED POSITION. SEATS SHALL BE 2 INCHES(51 MM) HIGH SIGNS SHALL BE LOCATED ON THE NEAREST ADJACENT WALL. SIGNS
<br /> L IIB-703.7.2.1. SIGNS IDENTIFYING VAN PARKING SPACES SHALL CONTAIN
<br /> E ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGN WITH THE DESIGNATION "VAN MAXIMUM. CONTAINING TACTILE CHARACTERS SHALL BE LOCATED SO THAT A CLEAR
<br /> 12 ACCESSIBLE." SIGNS SHALL BE 60 INCHES (1524 MM) MINIMUM ABOVE THE FINISH FLOOR SPACE OF 18 INCHES (457 MM) MINIMUM BY 18 INCHES (457 MM) MINIMUM,
<br /> U) FLOOR OR GROUND SURFACE MEASURED TO THE BOTTOM OF THE SIGN. 11B-604.5 GRAB BARS. GRAB BARS FOR WATER CLOSETS SHALL COMPLY WITH CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OF
<br /> SECTION 11B-609. GRAB BARS SHALL BE PROVIDED ON THE SIDE WALL CLOSEST ANY DOOR SWING BETWEEN THE CLOSED POSITION AND 45 DEGREE OPEN
<br /> 11B-502.6.1 FINISH AND SIZE. PARKING IDENTIFICATION SIGNS SHALL BE TO THE WATER CLOSET AND ON THE REAR WALL. WHERE SEPARATE GRAB BARS POSITION. WHERE PERMANENT IDENTIFICATION SIGNAGE IS PROVIDED FOR LU
<br /> +� ARE REQUIRED ON ADJACENT WALLS ATA COMMON MOUNTING HEIGHT, AN L- ROOMS AND SPACES THEY SHALL BE LOCATED ON THE APPROACH SIDE OF THE = f n N
<br /> REFLECTORIZED WITH A MINIMUM AREA OF 70 SQUARE INCHES (45161 MM2). SHAPED GRAB BAR MEETING THE DIMENSIONAL REQUIREMENTS OF SECTIONS V
<br /> N DOOR AS ONE ENTERS THE ROOM OR SPACE. SIGNS THAT IDENTIFY EXITS SHALL
<br /> U� 11B-502.6.2 MINIMUM FINE.ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGN 11B-604.5.1 AND IIB-604.5.2 SHALL BE PERMITTED. BE LOCATED ON THE APPROACH SIDE OF THE DOOR AS ONE EXITS THE ROOMQ
<br /> OR SPACE. 06
<br /> 00 BELOW THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL STATE "MINIMUM LOz
<br /> m FINE$250." 11B-604.5.1 SIDE WALL. THE SIDE WALL GRAB BAR SHALL BE 42 INCHES (1067 MM)
<br /> 06 LONG MINIMUM, LOCATED 12 INCHES (305 MM) MAXIMUM FROM THE REAR WALL
<br /> N AND EXTENDING 54 INCHES (1372 MM) MINIMUM FROM THE REAR WALL WITH THE J O
<br /> 11B-502.6.3 LOCATION.A PARKING SPACE IDENTIFICATION SIGN SHALL BE VISIBLE (n Q
<br /> FROM EACH PARKING SPACE. SIGNS SHALL BE PERMANENTLY POSTED EITHER FRONT END POSITIONED 24 INCHES (610 MM) MINIMUM IN FRONT OF THE WATER LU 00 ! ,
<br /> IMMEDIATELY ADJACENT TO THE PARKING SPACE OR WITHIN THE PROJECTED CLOSET. v
<br /> PARKING SPACE WIDTH AT THE HEAD END OF THE PARKING SPACE. SIGNS MAY 11B-604.5.2 REAR WALL. THE REAR WALL GRAB BAR SHALL BE 36 INCHES (914 Q Q
<br /> ALSO BE PERMANENTLY POSTED ON A WALL AT THE INTERIOR END OF THE z Q
<br /> p� PARKING SPACE. MM) LONG MINIMUM AND EXTEND FROM THE CENTERLINE OF THE WATER F--- T � 07
<br /> CLOSET 12 INCHES (305 MM) MINIMUM ON ONE SIDE AND 24 INCHES (610 MM) U y U Q
<br /> m MINIMUM ON THE OTHER SIDE. W I� W CO
<br /> FT 11B-502. 6.4 MARKING. EACH ACCESSIBLE CAR AND VAN SPACE SHALL HAVE `- O O Q
<br /> m O SURFACE IDENTIFICATION COMPLYING WITH EITHER SECTION 11B-502.6.4.1 OR 11B-604.6 FLUSH CONTROLS. FLUSH CONTROLS SHALL BE HAND OPERATED OR 0
<br /> �I 11B 502.6.4.2. AUTOMATIC. HAND OPERATED FLUSH CONTROLS SHALL COMPLY WITH SECTION w
<br /> 11B-502.6.4.1 THE PARKING SPACE SHALL BE MARKED WITH AN INTERNATIONAL IIB-309 EXCEPT THEY SHALL BE LOCATED 44 INCHES (1118 MM) MAXIMUM ABOVE
<br /> C) THE FLOOR. FLUSH CONTROLS SHALL BE LOCATED ON THE OPEN SIDE OF THE
<br /> SYMBOL OF ACCESSIBILITY COMPLYING WITH SECTION 11B-703.7.2.1 IN WHITE ON WATER CLOSET EXCEPT IN AMBULATORY ACCESSIBLE COMPARTMENTS STORE #: 65246
<br /> N A BLUE BACKGROUND A MINIMUM 36 INCHES WIDE BY 36 INCHES HIGH (914 MM X COMPLYING WITH SECTION IIB-604.8.2.
<br /> U) 914 MM). THE CENTERLINE OF THE INTERNATIONAL SYMBOL OF ACCESSIBILITY PROJECT #: 88584-001
<br /> N SHALL BE A MAXIMUM OF 6 INCHES (152 MM) FROM THE CENTERLINE OF THE 11B-604.7 DISPENSERS.TOILET PAPER DISPENSERS SHALL COMPLY WITH ISSUE DATE: 50% CD 1-29-21
<br /> E PARKING SPACE, ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACE SECTION 118-309.4 AND SHALL BE 7 INCHES (178 MM) MINIMUM AND 9 INCHES (229
<br /> AND ITS LOWER CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THE MM) MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO THE DESIGN MANAGER: J. RAMOS
<br /> PARKING SPACE LENGTH. CENTERLINE OF THE DISPENSER. THE OUTLET OF THE DISPENSER SHALL BE PRODUCTION DESIGNER:
<br /> 0 BELOW THE GRAB BAR, 19 INCHES (483 MM) MINIMUM ABOVE THE FINISH FLOOR CHECKED BY: SKIM
<br /> E 11B-502.6.4.2 THE PARKING SPACE SHALL BE OUTLINED OR PAINTED BLUE AND AND SHALL NOT BE LOCATED BEHIND GRAB BARS. DISPENSERS SHALL NOT BE
<br /> •\�- SHALL BE MARKED WITH AN INTERNATIONAL SYMBOL OF ACCESSIBILITY
<br /> COMPLYING WITH SECTION 11 B-703.7.2.1 A MINIMUM 36 INCHES WIDE BY 36 INCHES PAPER FLOW.OF A TYPE THAT CONTROLS DELIVERY OR THAT DOES NOT ALLOW CONTINUOUS Revision Schedule
<br /> HIGH (914 MM X 914 MM) IN WHITE OR A SUITABLE CONTRASTING COLOR. THE
<br /> N CENTERLINE OF THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL BE A Rev Date By Description
<br /> V) MAXIMUM OF 6 INCHES (152 MM) FROM THE CENTERLINE OF THE PARKING SPACE, LAVATORIES
<br /> ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACE AND ITS LOWER
<br /> (j CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THE PARKING SPACE. 11B-606 LAVATORIES AND SINKS
<br /> 11B-502.8 ADDITIONAL SIGNAGE.AN ADDITIONAL SIGN SHALL BE POSTED EITHER; 11B-606.2 CLEAR FLOOR SPACE. A CLEAR FLOOR SPACE COMPLYING WITH
<br /> 1) IN A CONSPICUOUS PLACE AT EACH ENTRANCE TO AN OFF-STREET PARKING SECTION I IB-305, POSITIONED FOR A FORWARD APPROACH, AND KNEE AND
<br /> FACILITY OR 2) IMMEDIATELY ADJACENT TO ON-SITE ACCESSIBLE PARKING AND TOE CLEARANCE COMPLYING WITH SECTION I IB-306 SHALL BE PROVIDED.
<br /> VISIBLE FROM EACH PARKING SPACE.
<br /> SHEET TITLE:
<br /> 00 11B-606.3 HEIGHT. LAVATORIES AND SINKS SHALL BE INSTALLED WITH THE ACCESSIBILITY NOTES
<br /> N 11B-502.8.1 SIZE. THE ADDITIONAL SIGN SHALL NOT BE LESS THAN 17 INCHES (432 FRONT OF THE HIGHER OF THE RIM OR COUNTER SURFACE 34 INCHES (864
<br /> MM)WIDE BY 22 INCHES (559 MM) HIGH. MM) MAXIMUM ABOVE THE FINISH FLOOR OR GROUND.
<br /> O 11B-606.4 FAUCETS. CONTROLS FOR FAUCETS SHALL COMPLY WITH SECTION
<br /> 11B-502.8.2 LETTERING. THE ADDITIONAL SIGN SHALL CLEARLY STATE IN LETTERS I IB-309. HAND-OPERATED METERING FAUCETS SHALL REMAIN OPEN FOR 10 SCALE: AS SHOWN
<br /> j WITH A MINIMUM HEIGHT OF 1 INCH (25 MM)THE FOLLOWING: SECONDS MINIMUM.
<br /> CD SHEET NUMBER:
<br /> N
<br /> N
<br /> 005
<br /> N
<br />
|