INSTALL_2022 - Laserfiche WebLink

Home Browse Search

BE Z ¢ � F IaL Z Q 7 a 2 DO �r azCSa h�� DUgN >>> a mooara o _8 s a Not Used a Not Used Not Used T4 SCALE NONE T4 SCALE NONE T4 s J Q N z WIRE SHIELDED CABLE 0¢a SUMP O 3 SUMP �5 a 3"0 x 12"LONG FIBERGIlSB PIPE BONDED }°BALL VALVE W/BARB FITTING AT TO SUMP INNER WALL USING GASOLINE FACTORY INSTALLED BUSHING COMPATIBLE EPDXY RESIN. 0 SUMP SENSOR IN HOLDER 31 (SEE NOTE�3) CONTRACTOR TO INSTALL GALVANIZED METAL }/g H 1/4 SS BUSHING OR FIBERGLASS SPACER TO ALLOW FIBERGLASS mo k PIPE TO CLEAR SUMP COLW2"LIP". IL NSTALLED AT FACTORY APEX OF FIBERGLASS CONTRACTOR TO USE GASOLINE-COMPATIBLE TANK EPO%T TO BONA SPACER TO SUMP. APE%OF FIBERGLASS a CONTRACTOR MAY USE UEQUIVALE FIBERGLASS O TANK PIPE.DR ANY OTHER ENVIRONMENT MATERIAL THAT CAN WITHSTAND ENVIRONMENT OF SUMP TO SECURE THE SUMP SENSOR 50 THAT IT CAN BE REMOVED FOR INSPECTION AND RESECURED WITHIN THE SUMP �pypF[sslq�fym Tank Sump Drain Port Detail(Typ.Fill+Turbine Sumps) T4- GALE.,-,-O Not Used Sensor Holder Detail T4- SCALE:N ONE ra- SCALE 2-=l-" a' 34•L,6 D.D. .. - MINI HYDROSTATIC 26 Sheet Notes SENSOR 32-3/4"Neck O.D. 1.- PIPE&CONDUIT PENETRATIONS: FACTORY SUPPLIED ALL PENETRATIONS OF THE TANK SUMPS SHALL BE SEALED WITH DOUBLE BULKHEAD OUNCE SHALL BE INSTALLED PERPENDICULAR ml f SUMP RESERVOIR & TO SUMP WALL TO ENSURE THE PROPER INSTALLATION OF ALL BULKHEAD FWATER ITTINGS AND RESULTANT ER TIGHTNESS,ALL PIPING, MANOMETER 3D"I.O. HOPE METER TO CONDUIT AND GROUNDS THAT PENETRATE THE SUMP SIDE WALLS MUST BE SEALED IN SUMPS.SUMPS SHALL BE HYDROSTATICALLY TEST PORT FOR TESTED WITH STANDING WATER FOR A PERIOD OF 24 HOURS TO INSURE THAI THE SUMPS ARE WATERTIGHT. y isi ^gg CONTINUITY TESTING 2.- PIPING TESTING: a p Y TESTING OF THE SECONDARY CONTAINMENT PIPING IS REQUIRED.WE CONTAINMENT TERMINATION FITTING IN THE SUMP IS TO BE INSTALLED .H THE VALVE TURNED DOWN. THE PIPING IS LD BE CONTINUOUSLY MONITORED BY VACUUM, PRESSURE OR ap ROUND BOOT H1'URO REND.THEREFORE THE VALVE UNLESS BEING TESTED SHOULD REMAIN CLOSED, N SLIP ON RISER O E%TENSION 0j 4 3.- SUMP SENSORS: E FIELD SEALED JOINT.— 54"I.D. SENSOR IT BE UMP AREA AT SIDE OF TANK WHERE PRODUCT PENETRATION INTO SUMP IS MADE AND BELOW LOWEST PENETRATION FITTING WITHIN SUMP AREA.MOUM SENSOR FLUSH TO LOWEST POINT IN SUMP BOTTOM.ALL TANK SUMP SENSORS SHALL BE (ADHESIVE SUPPLIED a W/KIT) NONWING AND POSITION SENSITIVE MANHOLE CROWNS: ALL MANHOLE OPENINGS ON THE TANK SLAB SHALL BE INSTALLED WITH A 2"%18"RUN CROWN OF CONCRETE TO PREVENT WATER ON INTO THE MANHOLE, US,GE O 3 FACTORY _-_ 5.- U.G. ONDUR: W i LAY-UP ALL U.G.CONDUIT TO TANK SUMPS SHALL BE ROBROY RIGID STEEL WC COATED SCHEDULE 40(NO SUBSTITUTIDNS).CONDUIT 1 MINIMUM BURY DEPTH IS 24"PER CODE.ALL JUNCTION BORES SHALL BE CUSS 1 DIV.2 RATED.ALL ELECTRICAL CONDUIT IN Q COLLAR BONDED SUMPS SHALL INCLUDE A SEAL-OFF ENTERING AND LEAVING,SEAL-OFFS SHALL BE INSTALLED 5"MIN,ABOVE HIGHEST TO TANKPENETRATION IN SUMP. 4B"DIA.POLYGON SUMP BODY 6.- STAINLESS STEEL FNTINGS: (8-20"X 19"FEAT PANELS) N CONTRACTOR TO PROVIDE ALL MISCELLANEOUS NET FITTINGS AND NIPPLES FOR CONNECTIONS TO TURBINES,SIPHON SYSTEM AND VAPOR RECOVERY SYSTEM.ALL STAINLESS STEEL FITTINGS SHALL BE MANUFACTURED BY"STANDARD PIPE PRODUCTS" OR EQUAL SPECIFICATIONS AS FOLLOWS: JOINT DETAILS FACTORY INSTALLED ED 5.BUSHING. FININGS DIMENSIONS MATERIAL THREAD PRESSURE RATING 5. OCONTRACTOR TO ADDITIONALLY 1-1 WRAP & LAMINATE AT "NOTE PEES,ELBOWS) CONNECTION FOLLOWING CURING OF ADHESIVE.SPECIFIC ATTENTION CONTRACTOR SHALL BE HELD RESPONSIBLE FOR PROPER CUSS 150/PN 20 ASME 816.3 ASTM A-182 ASME B.1 20.1 ASME B16.3 MUST BE GIVEN TO SURFACE PREP AS TESTING REQUIREMENTS WILL INSTALLATION & PREPARATION PER MANUFACTURERS S.S.UNIONS DETECT THE SMALLEST OF FLAWS. ALL MATERIALS MUST BE INSTRUCTIONS AND SHALL REINSTALL SUMPS IF CLASS 150/PN 20 ASME 81639 ASTM A-182 ASME AT 20.1 ASME BISS GO 13 MEA118LE WITH GASOLINE,GASOLINE WITH 15%METHANOL AND HYDROSTATIC AND SHOWS LEAKING IN THIS AREA OF S.S.PIPE 10%ETHANOL FIBERGLASS AND RESIN MUST EXTEND 1/2"BEYOND THE SUMP.TESTING OF SUMP SHALL BE PERFORMED CUSS 150/PN 20 ASTM A733 ASTM A-312 ASME B.1 20.1 ASME EMS COVERAGE OF ADHESIVE. AUER REDUCER IS INSTALLED. Not Used7�- CORROSION PROOF: Double Wall Sump Installation Detail at Tank#5 ALL TURBINE PUMP HEADS TO HAVE ADVANCED CORROSION PROOF PROTECTION WITH E-COATED FINISH, H T4- SCALE.NONE T4- scnLE:I"=1'-D"