Laserfiche WebLink
M8.1DETAILSDATE REVISION/ SET05.06.21PERMIT APPLICATIONWMB PROJECT:PUBLISH HISTORY5757 Pacific AvenueSuite 226Stockton, CA 952072000 L StreetSuite 125Sacramento, CA 95811209.944.9110 T209.944.5711 Fwww.wmbarchitects.comDAVID'S PIZZA T.I.4755 Quail Lakes Dr. - Ste. AStockton, CA 9520720-068MECHANICALHOOD STYLEFOR WALL CANOPIESIN THE FOLLOWING LOCATIONSHANGING ANGLES WILL BE LOCATED(24" High 2.25"4.125"DIM FROMHood)FRONT(24" High DIM REAR FROMFROMHood)SIDESDIM ND-2 (-WI)Exhaust onlyVHB (-B)2.25"2.25"2.25"2.25"UNITS SHALL INCLUDE STAINLESS STEEL HANDLES AND A FASTENING DEVICE TO SECURE THE TWOCAPTRATE FILTERS ARETEA BUILT IN COMPLIANCE WITHINT. MECH. CODE (IMC)UL STANDARD #1046NSFNSF STANDARD #2ACCORDANCENo. 96NFPAWITHBUILTINSLIDTERONFPA #96CHBNRANI,ORM.YRORLAIGNTSBATTO DELIVER EXCEPTIONAL FILTRATION EFFICIENCY.2-INCH DEEP HOOD CHANNEL(S).COMPONENTS WHEN ASSEMBLED.PARTICLES FIVE MICRONS IN SIZE, AND 90% GREASE PARTICLES SEVEN MICRONS IN SIZE AND***GREASE EXTRACTION EFFICIENCY PERFORMANCE SHALL REMOVE AT LEAST 75% OF GREASEFILTER IS CONSTRUCTED OF 430 STAINLESS STEEL, AND SIZED TO FIT INTO STANDARDLARGER, WITH A CORRESPONDING PRESSURE DROP NOT TO EXCEED 1.0 INCHES OF WATER GAUGE.THE CAPTRATE GREASE-STOP SOLO FILTER IS A SINGLE-STAGE FILTER FEATURINGA UNIQUE S-BAFFLE DESIGN IN CONJUNCTION WITH A SLOTTED REAR BAFFLE DESIGN,SPECIFICATION: CAPTRATE GREASE-STOP SOLO FILTERRRFILTRATION EFFICIENCY (%)00.1102030401PARTICLE DIAMETER (um)10FILTER COLLECTION EFFICIENCY90506080701002" Captrate Grease-Stop Solo FilterRRRESISTANCE VS. AIRFLOW - 0.8RESISTANCE (in. H20)0.2000.40.611.21.61.4600AIRFLOW (cfm)20040080010002" Captrate Grease-Stop Solo FilterRRLDIESTR(H x W x D)ACTUAL DIMENSIONS9-5/8" x 19-5/8" x 1-7/8"9-5/8" x 15-5/8" x 1-7/8"19-5/8" x 19-5/8" x 1-7/8"19-5/8" x 15-5/8" x 1-7/8"15-5/8" x 19-5/8" x 1-7/8"15-5/8" x 15-5/8" x 1-7/8"11-5/8" x 19-5/8" x 1-7/8"11-5/8" x 15-5/8" x 1-7/8"12 x 2010 x 2010 x 1612 x 1616 x 2016 x 1620 x 16NOMINAL SIZE(H x W)20 x 20(FEET PER MINUTE)1.236.81.000.780.965.64.65.61.781.391.789.17.48.9(SQ. FEET)FREE AREA(POUNDS)2.2811WEIGHTR2002502752251501751250.901.301.501.000.450.750.35STATIC PRESSURE(WATER GAUGE)VELOCITY100R0.25ALL OTHER HOOD MODELS CONTACTCAPTIVE AIRE FOR HANGING ANGLELOCATIONSdrain through a concealed grease troughand into this removeable cup.Grease cup will be supported by 2 studson the inside wall of the hood. The grease willBatton Strip Detail1-3/8"finish S/S of the same guage and material as theBacksplash is to be manufactured from #3 or #4hoods. It will be supplied with Batton strips andend strips as needed to close all seams and edges.Stainless Steel Backsplash1/2"and Sidesplash8' 0"NOM./8' 0.00"OD.60"12"24"6"10"24"48"6"10"24"§24"30"Ø12"48"24"30"Ø12"U.L. LISTED L55 SERIES E26 CANOPY LIGHTFIXTURE - HIGH TEMP ASSEMBLY.LATERAL BRACING DETAILREFER TO KITCHEN HOOD HANGER ANDDRAIN FULL PERIMETER GUTTER.SEE HOOD TABLE.§EXHAUST RISER.HANGING ANGLE.L55 SERIES E26 CANOPY LIGHT FIXTURE -HIGH TEMP ASSEMBLY, INCLUDES CLEAR THERMALAND SHOCK RESISTANT GLOBE (L55 FIXTURE).23.5% OPEN STAINLESSSTEEL PERFORATED PANEL.ATTACHING PLATES.SUPPLY RISER WITHVOLUME DAMPER.6"2 3/4"12"18"BACKSPLASH 80.00" HIGHX 96.00" LONG.FIELD WRAPPER 17.00" HIGH(SEE HOOD OPTIONS TABLE).EQUIPMENTBY OTHERS.80"24" NOM.60"IT IS THE RESPONSIBILITYOF THE ARCHITECT/OWNER TOENSURE THAT THE HOOD CLEARANCEFROM LIMITED-COMBUSTIBLEAND COMBUSTIBLE MATERIALSIS IN COMPLIANCE WITHLOCAL CODE REQUIREMENTS.SEE DETAILREFER TO KITCHENHOOD MTG. DETAIL:FRAMING AND INSULATION, ETC.DRAWING FOR DETAIL OF WALLBACKSPLASH, REFER TO STAINLESS STEEL BACKSPLASHDETAIL THIS SHEET & ARCH.SEE DETAIL