WORK PLANS - Laserfiche WebLink

Home Browse Search

CLIENT: =t 22 223 28 PRIMARY RETALIX ALLIED EC PUMP DISPa° N; POS ANDI BOX LOW #1 � BOX VOLTAGE TLS-350 26 PIB DISPENSER (SERIAL RS-485) DISP WIRING #2 200 DISCONNECT beak Detecfion System Notes (PUMP INTERFACE BOARD) >- DISP 27 233 TYP n. CAT 1. WARNING: J-BOX MSM MONITOR SENSOR & PROBE WIRING IS INTRINSICALLY SAFE WIRING AND MUST BE SEPARATE OR DEBIT FROM ALL OTHER WIRING AND INSTALLED IN SEPARATE CONDUIT. MAXIMUM CABLE LENGTH CAT RS-485 BETWEEN MONITOR CONSOLE AND SENSORS IS 1,000 FEET. INTERFACE 2. CAUTION: 120 VAC WIRING MUST NOT BE CONNECTED TO LOW VOLTAGE CONNECTIONS. DAMAGE FROM MISWIRING IS NOT COVERED BY WARRANTY. INSTALLING CONTRACTOR TO BE HELD DB9 CONTROL RESPONSIBLE. SAM TERCOM/COM CABLE RS-485 PIC DEBIT q WIRING 3. INSTALL TANK MONITOR SYSTEM PER MANUFACTURER'S INSTALLATION INSTRUCTIONS. ISCQN 4. USE BELDEN CABLE # 88760 OR APPROVED EQUAL FOR ALL SENSOR AND PROBE WIRING. DB9 CONTROL ARCO CABLE SHARED CONDUIT ETHERNET 5. RUN RIGID METAL CONDUIT FOR PROBE AND SENSOR WIRING FROM THE MONITOR CONSOLE 235 WIRING CAT 5 DISP (CAT 5 & TO THE INTRINSICALLY SAFE WIREWAY. CONDUIT MUST ENTER THE MONITOR WHERE LLC DISCONNECT1 INTERCOM) TO EACH KNOCKOUTS ARE PROVIDED. NO OTHER CONDUIT ENTRY IS PERMITTED. DB9 CONTROL >- DISPENSER CABLE < DISP (TYPICAL) 6. SPECIAL NOTE: IT IS THE INTENT OF THIS DESIGN THAT ANY DETECTED LEAK OR ANY FAILURE TERCOM/COM INTERCOM l #2 OF THE LEAK DETECTION SYSTEM, WILL RESULT IN THE INTERRUPTION OF ALL POWER TO THE 234 WIRING (BELDEN CABLE ea760) PRODUCT PUMPS. DISP TYP 7. CERTIFIED INSTALLERS- ALL MANUFACTURERS TRAINING REQUIREMENTS SHALL BE MET BY CONTRACTOR INSTALLING SENSORS/PROBES AND WIRING TO MONITORING SYSTEM. 8. IT IS THE RESPONSIBILITY OF THE INSTALLING CONTRACTOR TO NOTIFY THE VEEDER ROOT LOW VOLTAGE DISPENSER WIRING DISCONNECTS DISTRIBUTOR FOR STARTUP. PRIMARY DISCONNECT: Power Integrity Corp. Model: DDS-8DM4WPE 0 NOTE: COM DISCONNECT (PIC): Power Integrity Corp. Model: DDS-8DB4C (IF PIC is located g SEE MANUFACTURERS WIRING DIAGRAM FOR SPECIFIC WIRING AND FURTHER INFORMATION. 11, �® OPTIONAL "MSI" POS CAN In Dispenser) 10. EACH TURBINE RELAY IS TO BE WIRED INTO THE MONITOR CONTROL SO THAT AN ACTIVATION INTERCOM DISCONNECT: Power Integrity Corp. Model: DDS-8DB4C OF TURBINE SIDE SUMP SENSOR OR ANNULAR SPACE SENSOR OR LLD WILL SHUT DOWN THE BE WIRED SIMILARLY ETHERNET DISCONNECT: Power Integrity Corp. Model: DDS-EWS8D(Wall Mount) TURBINE FOR THAT TANK. . or DDS-ERS8D (Rack Mount) 18215 72ND AVENUE SOUTH KENT, WA 98032 (425)251-6222 ARCO W A Y N E " NON - e " 9N0Nee9 4 T O R E T AU X PO S (425)251-8782 FAX SCALE: NTS CML ENGINEERING, LAND PUNNING, SURVEYING, ENVIRONMENTAL SERVICES NO. DATE REVISION DESCRIPTION 1 2 3 4 o a L� CAT 5 C a � e � n sto � � a f i 0 n Gu ' d e IST-VFC MOTES VEEDER-ROOT TLS-350 NOTES 1. EXCESSIVE FORCE SHOULD NOT BE USED TO PULL IN NEW CABLE. PULL FORCE SHOULD NOT EXCEED REQUIREMENTS FOR THIS SYSTEM: ® WARNING: IN INSTALLATION AND USE OF THIS PRODUCT, 25 LBS. 1. TWO OR MORE VFC CONTROL BOXES WITH LATEST SOFTWARE. PLEASE CONTACT FE PETRO FOR COMPLY WITH THE NATIONAL ELECTRICAL CODE: FEDERAL, 2. CABLE SHALL NOT BE KINKED, KNOTTED, OR OTHERWISE DEFORMED DURING INSTALLATION. AVAILABILITY. STATE AND LOCAL CODES. IN ADDITION, TURN OFF POWER 2. VEEDER-ROOT TLS-350 WITH LATEST TLS-350 SOFTWARE. PLEASE CONTACT VEEDER-ROOT FOR AND TAKE OTHER NECESSARY PRECAUTIONS DURING 3. PROPER CABLE SUPPORT HARDWARE SUCH AS J-HOOKS SHALL BE USED TO PREVENT RIPPING OR AVAILABILITY. INSTALLATION, SERVICE AND REPAIR TO PREVENT PERSONAL z FRAYING OF CABLE. WHERE USED, STAPLES SHALL BE NON-METALLIC PLASTIC. STAPLE SHOULD BE 3. SET THE VFC WITH THE PLLD TRANSDUCER INSTALLED IN ITS PUMP TO BE THE MASTER VFC. INJURY, PROPERTY LOSS AND EQUIPMENT DAMAGE. SEAL LOOSE ENOUGH SUCH THAT CABLE JACKET IS NOT CRIMPED. 4. 18 AWG 3-WIRE SHIELDED COMMUNICATION CABLE (300 V MINIMUM) CONNECTING VFCS. Q�pF E S�/® 5. AN FE PETRO MODEL 65 PSI CHECK VALVE OR ANON-VENTED CHECK VALVE SHALL BE WARNING: DISCONNECT ALL POWER BEFORE MAKING AN 4. CABLE BUNDLES MAY BE SECURED WITH LOOSE FITTING WIRE TIE OR VELCRO TIE WRAPS. CABLES INSTALLED ON THE SLAVE PUMPS (IF USED). CONNECTIONS TO PREVENT DEATH, SERIOUS INJURY, SHALL NOT BE OVER TIGHTENED SUCH THAT CRUSH STRESS IS EVIDENT. 6. WIRE VFC CONTROLLERS ACCORDING TO THE LATEST FE PETRO TECHNICAL BULLETIN. EXPLOSION ELECTRICAL SHOCK. MONITOR MUST NEVER BE 7. INSTALLATION MANUALS FOR BOTH VEEDER-ROOT TLS-350 & FE PETRO VFC WILL BE AVAILABLE OPERATED UNLESS THE FRONT COVER IS CLOSED OVER THE C-0 5. CABLE SHALL BE ROUTED TO PERMIT SWEEPING BENDS, NOT RIGHT ANGLES OR SHARP BENDS. CABLE DURING INSTALLATION. BARRIER TERMINALS IN THE INTRINSICALLY SAFE AREA. W C 1 rn RUNS SHALL BE INDIVIDUALLY SUPPORTED. BASIC OPERATION FOR THIS CONFIGURATION: NOTES: 6. A MINIMUM OF CABLE JACKET SHALL BE REMOVED WHEN TERMINATING. CABLE JACKET SHALL EXTEND AS CLOSE AS PRACTICAL TO THE TERMINATION POINT, LEAVING NO MORE THAN 3/4 INCH OF WIRE 1. THE VEEDER-ROOT TLS-350 SYSTEM MONITOR THE TANK PRODUCT LEVELS. 1. WIRING TO PROBES, SENSORS, & PLLD MUST BE SHIELDED MULTI-STRAND, GAS AND '�� / V 1 EXPOSED. 2. WHEN DEMAND FOR PRODUCT IS CALLED FOR, A 120 VAC HOOK SIGNAL FROM DISPENSER IS PRESENT, THE VEEDER-ROOT TLS-350 SYSTEM WILL TURN ON A PUMP ACCORDING TO THE PRODUCT OIL RESISTANT SIZES FROM AWG X18 TO AWG #14. BARRIER GROUND WIRING MUST BE � OF CA�-\F® 7. MAINTAIN TWISTED CONFIGURATION OF WIRE PAIRS TO WITHIN 1/2 INCH OF THE TERMINATION POINT. LEVEL IN THE TANKS, DICTATED BY CONSOLE CONFIGURATION. AWG ESI#12 OR LARGER. 3. WHEN DEMAND FOR PRODUCT RISES, MORE PEOPLE DISPENSING PRODUCT, WHICHEVER VFC IS IN THE LEAD POSITION CAN CALL FOR ADDITIONAL VFC TO TURN ON. 2. CONNECT WITH #12 AWG (OR LARGER) CONDUCTOR THE BARRIER GROUND TO THE 8. WIRES SHALL NOT BE SPLICED. DAMAGED CABLE SHALL BE REPLACED, NOT REPAIRED. 4. WHEN THE DEMAND FOR PRODUCT GOES AWAY, THE VEEDER-ROOT SYSTEM WILL PERFORM A LINE EARTH GROUND BUS AT THE POWER DISTRIBUTION PANEL. LEAK TEST USING THE VFC DESIGNATED AS THE MASTER ACCORDING TO VEEDER-ROOT'S LINE TEST 3. QDENOTES FIELD WIRING CONNECTION USING WATERPROOF CONNECTORS SUPPLIED 9. LEAVE APPROXIMATELY 18 INCHES OF SPARE WIRE AT OUTLET AND CONNECTION POINT. PROTOCOL. 5. IN THIS CONFIGURATION, IF THERE ARE ANY FAULTS IN THE SYSTEM THE WHOLE SYSTEM WILL BE WITH THE PROBE(S) AND SENSOR(S). 10. ENSURE ADEQUATE SEPARATION WHEN RUNNING CAT 5 CABLE PARALLEL TO POWER WIRING. CABLE SHUT DOWN. SHALL NOT BE ROUTED THROUGH SAME BORE HOLES AS POWER WIRING. WHERE POSSIBLE CAT 5 4. INTRINSICALLY SAFE WIRING SHALL BE INSTALLED IN ACCORDANCE WITH THE CURRENT CABLES SHOULD CROSS POWER WIRES AT 90 DEGREE ANGLES. MAINTAIN SEPARATION BETWEEN CABLE THE WIRING DIAGRAM IN FIGURE 1 SHOWS THE CONNECTIONS BETWEEN THE VEEDER-ROOT POWER BAY VERSION OF THE NEC AND NFPA CODES.. AND OTHER WIRING AS FOLLOWS: CONSOLE AND THE MASTER SLAVE VFCS. 5. TO MAINTAIN INTRINSIC SAFETY AND PROPER SYSTEM OPERATION, PROBE AND 1. FOLLOW ALL SAFETY AND INSTALLATION INSTRUCTIONS IN THE VEEDER-ROOT SITE PREP AND SENSOR WIRING MUST BE INSTALLED WITHIN SEALED CONDUIT. DEVELOPMENT INFORMATION: INSTALLATION INSTRUCTIONS FOR THE VEEDER-ROOT TLS-350. ARCO HT PURPOSE TYPE OF WIRE MIN. SEPARATION 2. FOLLOW ALL SAFETY AND INSTALLATION INSTRUCTIONS IN THE IST-VFC INSTALLATION AND OWNERS 6. ELECTRICAL RATING POWER INPUT - 120VAC, 50/60 HZ, 600 WATTS MAX. MANUAL FOR WIRING NOT SHOWN IN FIGURE 1. 30M a tmf /pm OPEN WIRING LESS THAN 300 VOLTS 2 INCHES 3. SET SW3 SWITCHES ACCORDING TO MASTER-SLAVE CONFIGURATION NOT FOR MASTER-SLAVE 7. REFER TO THE LATEST "SITE PREPARATION AND INSTALLATION INSTRUCTIONS,- MANUAL ALTERNATING CIRCUIT (M-S/AC). IF VFCS ARE SET IN M-S/AC THE PUMPS WILL NOT TURN ON IN A FOR ACTUAL LOCATION OF CONDUIT ENTRY INTO TLS-350 MONITOR. FUEL CANOPY POWER SUPPLY WIRE IN CONDUIT OR ARMORED OR PREDICTABLE MANNER. v� 65 M PD9 NON-METALLIC SHEATH CABLE/POWER NONE 4. CALIBRATE CONTROLLERS ACCORDING TO CALIBRATION INSTRUCTIONS IN IST-VFC INSTALLATION AND 8. REFER TO THE LATEST LINE LEAK DETECTOR "SITE PREPARATION AND INSTALLATION" GROUND WIRES OWNERS MANUAL. MANUAL. 4 INCHES RADIO & TELEVISION ANTENNA LEAD & GROUND WIRES ADDITIONAL NOTES: 9. RS-232 MODULE IS LOCATED IN THE COMMUNICATIONS COMPARTMENT AND MUST BE SITE ADDRESS: WITHOUT GROUNDED SHIELD ORDERED SEPARATELY. 1. FOR ADDITIONAL INFORMATION, REFERENCE THE LATEST VEEDER-ROOT SITE PREPARATION AND ESCALM AMUE SIGNAL & CONTROL WIRE OPEN WIRING NOT OVER 300 VOLTS NONE INSTALLATION MANUAL FOR INSTALLATION INSTRUCTIONS OF PLLD USING A MASTER/SLAVE 10. BONDING LOCKNUTS AND OR BONDING BUSHINGS SHALL BE USED AT ALL CONDUIT ©K 4JAv O CONFIGURATION. ENTRANCES TO THE TLS-350R ENCLOSURE AND AT ANY JUNCTION BOX/WIREWAYS IN THE ERCALGiAGA COMMUNITY TELEVISION SYSTEMS NON-HAZARDOUS AREA TO ENSURE POSITIVE CONDUIT GROUNDING. CATV CABLES COAXIAL CABLES WITH GROUNDED NONE 2. ANON-VENTED CHECK VALVE, VEEDER-ROOT PART NUMBER VR-330020-416, OR FE PETRO SHIELD MODEL 65-PSI CHECK VALVE MUST BE INSTALLED ON THE SLAVE TANK TURBINE TO ENSURE PROPER 11. SOFTWARE ENHANCEMENT MODULE REQUIRED (#330160-012) AND MUST BE FAC0 OPERATION OF SYSTEM AND PROVIDE ADEQUATE LINE LEAK PROTECTION. REFER TO THE LATEST FE ORDERED SEPARATELY. PETRO TECHNICAL SERVICE BULLETIN, FOR MORE SPECIFIC DETAILS. DESIGNED BY: ALLIANCE z&DM: TELEPHONE SERVICE 12. FOR 2 PUMPS IN SINGLE TANK OPERATION, PUMP SENSE MODULE REQUIRED A DROP WIRE AERIAL OR BURIED 2 INCHES 3. THE VEEDER-ROOT TLS-350 SYSTEM MUST BE PROGRAMMED USING THE CORRECT DISPENSER (#847490-204) AND MUST BE ORDERED SEPARATELY, IF USING PLLD, PUMP SENSE CHECKED BY: OV BP REPM: MODE. THE PROGRAMMER MUST SELECT THE MANIFOLDED ALTERNATE MODE IN THE PLLD SET-UP MODULE IS NOT ALLIANCEREQUIRED (ELECTRONIC LINE LEAK DETECTOR IS DOING THE PUMP DRAWN BY: AL ALLIANCE PM: SIGN NEON SIGNS AND ASSOCIATED WIRING SECTION. REFER TO THE LATEST VEEDER-ROOT SYSTEM SET-UP MANUAL FOR SPECIFIC PROGRAMMING SENSE). VERSION: PROJECT No FROM TRANSFORMER 6 INCHES INSTRUCTIONS. V-12a0 �� 4. THE VEEDER-ROOT TLS-350 MUST BE PROGRAMMED USING THE MANIFOLDED TANK SET-UP. THE 13. NO SPLICING OF PROBE/SENSOR WIRE EXCEPT AT THE DEVICE ITSELF. 12/14/2 FLUORESCENT LIGHTING FLUORESCENT LIGHTING WIRE 5 INCHES PROGRAMMER MUST ASSIGN THE MASTER TANK T-1 TO LINE LEAK DETECTOR Q-1. THE SLAVE TANK DRAV4NG TITLE: T-2 TO LINE LEAK DETECTOR Q-2. SPECIFIC PROGRAMMING QUESTIONS SHOULD BE DIRECTED TO 14. CONTRACTOR MUST COMPLY WITH ALL THE TRAINING REQUIREMENTS OF LIGHTNING SYSTEM LIGHTNING RODS AND WIRES 6 FEET VEEDER-ROOT TECHNICAL SUPPORT DEPARTMENT. VEEDER-ROOT. 9��E VEEDER-HOOT� 15. SPECIFIC PROGRAMMING FOR VEEDER ROOT TLS-350 CONSOLE SHALL BE OBTAINED NOTES FROM THE LOCAL ENVIRONMENTAL COMPLIANCE MANAGER. SHEET NO: NM ITEMS ON MATERIALSIC ISTSSHEETS M.5 3D01O XX & M.53.02