Laserfiche WebLink
SHERWI <br />WILLIAM <br />Condition of ISO 8501-1 Swedish Std. <br />Surface BS7079:A1 SIS055900 SSPC NACE <br />Sa 3 Sa 3 SP 5 <br />Sa 2.5 Sa 2.5 SP 10 2 <br />Sa 2 Sa 2 SP 6 3 <br />Sal Sal SP 7 4 <br />C St 2 C St 2 SP 2 <br />D St 2 D St 2 SP 2 <br />C St 3 C St 3 SP 3 <br />D St 3 D St 3 SP 3 <br />White Metal <br />Near White Metal <br />Commercial Blast <br />Brush-Off Blast <br />Rusted <br />Pitted & Rusted <br />Rusted Power Tool Cleaning Pitted FL Rusted <br />Hand Tool Cleaning <br />AnnorSeal ARMORSEAL HS POLYURETHANE <br />Heavy FLOOR ENAMEL <br />Duty Floor <br />Coatings <br />PART A <br /> <br />B65-220 <br /> <br />SERIES <br />PART B <br /> <br />B65V220 <br /> <br />HARDENER <br />Revised: March 24, 2022 PRODUCT INFORMATION 8.46 <br />RECOMMENDED SYSTEMS <br />Concrete/Wood: <br />1 ct. ArmorSeal 1000HS (reduced 1 <br />Dry Film Thickness / ct. <br />Mils (Micronsl <br />pt/gal with R7K54) <br />2 cts. ArmorSeal HS Polyurethane 2.0-3.0 (50-75) <br />Floor Enamel <br />Steel: <br />1 ct. Recoatable Epoxy Primer 4.0-5.0 (100-125) <br />2 cts. ArmorSeal HS Polyurethane 2.0-3.0 (50-75) <br />Floor Enamel <br />Painted Surfaces in Sound Condition: <br />1-2 cts. ArmorSeal HS Polyurethane 2.0-3.0 (50-75) <br />Floor Enamel <br />The systems listed above are representative of the products use, <br />other systems may be appropriate. <br />SURFACE PREPARATION <br />Surface must be clean, dry, and in sound condition. Remove all <br />oil, dust, grease, dirt, loose rust, and other foreign material to <br />ensure ad-equate adhesion. <br />Refer to product Application Bulletin for detailed surface prepara- <br />tion information. <br />Minimum recommended surface preparation: <br />Iron & Steel: SSPC-SP6/NACE 3 <br />Concrete: SSPC-SP13/NACE 6, or ICRI <br />No. 310.2R, CSP 1-3 <br />Primer required <br />Surface Preparation Standards <br />TINTING <br />Tint Part A with Maxitoner Colorant at 100% tint strength (white tint <br />base and ultradeep tint base only). Five minutes minimum mixing <br />on a mechanical shaker is required for complete mixing of color. <br />APPLICATION CONDITIONS <br />40°F (4.5°C) minimum, 100°F (38°C) <br />maximum <br />(air, surface, and material) <br />At least 5°F (2.8°C) above dew point <br />75% maximum <br />Refer to product Application Bulletin for detailed application information. <br />ORDERING INFORMATION <br />Temperature: <br />Relative humidity: <br />Packaging: <br />Part A: <br />Part B: <br />1 gal (3.78L) and 5 gal (18.9L) <br />1 gal (3.78L) and 5 gal (18.9L) <br />DISCLAIMER <br />The information and recommendations set forth in this Product Data Sheet are <br />based upon tests conducted by or on behalf of The Sherwin-Williams Company. <br />Such information and recommendations set forth herein are subject to change and <br />pertain to the product offered at the time of publication. Consult your Sherwin- <br />Williams representative to obtain the most recent Product Data Information and <br />Application Bulletin. <br />Weight: 10.45 ± 0.2 lb/gal ; 1.25 Kg/L mixed, <br />may vary with color <br />SAFETY PRECAUTIONS <br />Refer to the SDS sheet before use. <br />Published technical data and instructions are subject to change without notice. <br />Contact your Sherwin-Williams representative for additional technical data and <br />instructions. <br />WARRANTY <br />The Sherwin-Williams Company warrants our products to be free of manufactur- <br />ing defects in accord with applicable Sherwin-Williams quality control procedures. <br />Liability for products proven defective, if any, is limited to replacement of the defec- <br />tive product or the refund of the purchase price paid for the defective product as <br />determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE <br />OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED, <br />STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER- <br />CHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE. <br />www.sherwin-williams.com/protective