INSTALL_2024 - Laserfiche WebLink

Home Browse Search

NOTE: NOTES: OUT OF HOLE INSTALLATION SEQUENCE: SEE TANK FUELING SITE PLAN FOR HYDROSTATIC EQUIPMENT SCHEDULE ALL STAGE I FILL AND VAPOR RISER ADAPTERS SHALL BE ELECTRICALLY GROUNDED TO PROMOTE NOTE: bp SPECIFIC TANK LAYOUT TANK #2B RESERVOIR THE RELAXATION OF STATIC CHARGE. ALL CAD WELDS W/ EXCEPTION OF "T" CONNECTIONS AT EACH TANK AND FINAL CAD WELD 0 ITEM DESCRIPTION THE BONDING AND GROUNDING FOR STATIC ELECTRICITY PROTECTION SHALL BE IN COMPLIANCE PER @ GROUND ROD NOTED IN SCHEDULE ON THIS SHEET MAY BE PREFABRICATED OUTSIDE NO. ALL APPLICABLE FEDERAL, STATE AND LOCAL CODES INCLUDING NFPA 30, FLAMMABLE AND THE TANK AREA AND BROUGHT TO SITE. COMBUSTIBLE LIQUIDS CODE, NFPA 77, RECOMMENDED PRACTICE ON STATIC ELECTRICITY, NFPA 70, HYDROSTATIC 1/2" 0 X 10' LONG COPPERBONDED GROUND ROD: CALIFORNIA ELECTRIC CODE, AND THE CALIFORNIA CODE OF REGULATIONS, SUBCHAPTER 15, 1 . MAKE "CABLE TO PIPING STEEL SURFACE" CADWELD CONNECTION CONNECTION WITH #4 RESERVOIR 0 G:) 11 ERICO" PART NO. 611300 (UL LISTED) PETROLEUM SAFETY ORDERS-REFINING, TRANSPORTATION AND HANDLING, ARTICLE 5, FIRE AND STRANDED WIRE TO EACH FILL AND STAGE I RISER OUTSIDE THE SUMP AREA. TO ASSURE OR EQUIVALENT EXPLOSIONS. 0 A COMPLETE CONNECTION, ANY PAINT OR COATING ON THE RISER SHALL BE REMOVED #4 AWG STRANDED BARE COPPER GROUND WIRE. PRIOR TO INSTALLATION OF THE CADWELD CONNECTION. PROVIDE TERMINAL CONNECTORS AT U-BOLT PER SECTION 6.4.1.3 OF NFPA 77, THE MEASURED TOTAL RESISTANCE IN THE GROUND PATH TO 2. APPLY "THERMOCAP" CATHODIC PROTECTION TO EACH OF THE CADWELDS ON RISERS. FILL SUMP 5 8 (TYP.) CONNECTIONS EARTH SHALL BE LESS THAN 1 MEGAOHM WHICH IS CONSIDERED ADEQUATE FOR RELAXATION OF TURBINE SUMP STATIC CHARGE. THE MAXIMUM ALLOWABLE GROUND PATH TO EARTH RESISTANCE FOR STATIC KE #4 STRANDED TO #4 STRANDED "T" CADWELD CONNECTIONS 6 (TYP.) CADWELD#4 WIRE CABLE TO GROUND ROD ELECTRICITY GROUNDING APPLICATIONS SHALL NOT EXCEED 100,000 OHMS. TO MAIN GROUND WIRE BACK TO GROUND ROD. THE CONDUCTORS SHALL HAVE 18" CONNECTION "ERICO" PART NO. GTT14AlL, USE MINIMUM COVER. EACH TANK SHALL HAVE SEPARATE GROUND WIRE TO GROUND ROD TO VENT STACK WELD METAL#32 PER SECTION 6.4.1.3 OF NFPA 77, THE RESISTANCE IN METALLIC BONDING AND OR GROUNDING 3. MAKE #4 STRANDED WIRE TO GROUND ROD CADWELD CONNECTION. CADWELD BOND GROUND WIRE TO CADWELD "T" CONNECTION FOR#4 BARE STRANDED SYSTEMS SHALL BE LESS THAN 10 OHMS. RESISTANCE HIGHER THAN 10 OHMS INDICATES CONNECTION MODEL NUMBER PER NUMBER OF TANKS. FILL SUMP ALL METALLIC RISERS AS WIRE CABLES. "ERICO" PART NO. TAC1 Ll L, USE#32 INADEQUATE CONNECTIONS. REQUIRED (TYP.)SEE CK) WELD METAL. A GROUNDING SYSTEM PER CEC CODE FOR CURRENT CARRYING CONDUCTORS SHALL BE NOTE: GROUND ROD BONDING DETAIL CONSIDERED MORE THAN ADEQUATE FOR A STATIC ELECTRICITY GROUNDING SYSTEM. ELECTRICAL CONDUIT, FUELING SYSTEM HARDWARE OR THE STATION ELECTRICAL GROUNDING 1 3 SYSTEM SHALL NOT BE USED FOR GROUNDING OR BONDING FILL AND VAPOR RISERS. INSTALL OUTSIDE OFCDCD--_�/ CLAMP, LIND EQUIPMENT P/N JR-1 50-6 (905)475-5086 PER THE NFPA 30, SECTION 5-6.3.4 ALL PARTS OF THE FILL PIPE ASSEMBLY, INCLUDING THE DROP TANK EXCAVATION IN NATIVE SOIL 4 TESTING: ARCO 4" NPT ADJUSTABLE COPPER GROUND CLAMPS, THE MINIMUM WIRE SIZE FOR BONDING AND GROUNDING SHALL BE COPPER AWG#4 MANNER.THAT WOULD POTENTIALLY PRODUCE STATIC DISCHARGE OR SPARKS OF ANY KIND. BP WEST COAST PRODUCTS,LLC 2 (TYP.) BURNDY GAR224C 4AWG GROUND CONNECTOR A 1/2" 0 BY 10' LONG COPPER CLAD STEEL GROUND ROD SHALL BE DRIVEN INTO NATIVE SOIL ONLY. FILL SUMP PLACING THE GROUND ROD INTO TANK PIT PEA GRAVEL SHALL NOT BE PERMITTED UNDER ANY THE FILL AND VAPOR RISERS SHALL BE TESTED AFTER INSTALLATION AND PERIODICALLY TO - OPW 104A-120OWT 12" H-20 RATED, BOLT DOWN WATER CONDITIONS. THE CONTRACTOR IS RESPONSIBLE FOR CLEARING ANY UNDERGROUND UTILITIES VERIFY BONDING AND GROUNDING COMPETENCY. 0 PRIOR TO INSTALLATION OF THE GROUND. 0 -14 TIGHT ACCESS COVER(USED IN DRIVE AREAS) THE MAXIMUM RESISTANCE FROM ANY FILL OR VAPOR ADAPTER TO THE BODY OF THE OPW 104A-1200 12" H-20 RATED, GRAVITY LID ACCESS THE GROUND ROD TO GROUND WIRE CONNECTION SHALL BE ACCESSIBLE THROUGH A H-20 RATED GROUND ROD SHALL NOT EXCEED 10 OHMS FOR A METALLIC RISER PIPE, SPILL CONTAINMENT 0 COVER(USED IN PLANTER AREAS) 12" DIAMETER MINIMUM ACCESS COVER TO ASSIST INSPECTION, MAINTENANCE AND TESTING. THE AND ADAPTER ASSEMBLIES. TURBINE SUMP x SCREW TYPE GROUND ROD CLAMP SHALL BE UL LISTED FOR DIRECT BURIAL. THE RESISTANCE THROUGH ANY COMPOSITE OR NONMETALLIC STAGE I CONTAINMENT FITTING ONE MAIN STRANDED#4 THHN CONDUCTOR SHALL BE RUN PAST EACH FILL SUMP. ONE STRANDED#4 SHALL BE MEASURED WITH A OHMMETER CAPABLE OF READING UP TO 10 MEGAOHMS. THE TANK #2A TANK #1 THHN CONDUCTOR SHALL BE ROUTED TO EACH FILL SUMP. INSTALLATION AT SUMP SHALL BE AS SUM COLLECTIVE RESISTANCE OF THESE SEMI-CONDUCTIVE ELEMENTS SHALL NOT EXCEED 3/4" DOUBLE WALL ENTRY FITTING. FOLLOWS AND MUST BE COMPLETED IN ORDER NOTED AS FOLLOWS: 100,000 OHMS. FOR THESE SYSTEMS, THE GROUND RESISTANCE TESTER MUST BE CONNECTED "BRAVO" MODEL NO. F-07S-0-DF TO THE GROUND CONDUCTOR CONNECTION ON THE COMPOSITE CONTAINMENT SYSTEM OR ADHESIVE- EP100 2 NEEDED PER PENETRATION RISER PIPE. NO. DATE REVISION DESCRIPTION FOR INSTALLATIONS WITHOUT AN EXPOSED GROUND ROD CONNECTION, TOTAL SYSTEM B B RESISTANCE SHALL BE MEASURED WITH A GROUND RESISTANCE TESTER BY A QUALIFIED 1/30/2024 INITIAL ISSUE FT-8 ELECTRICIAN FAMILIAR WITH GROUND TESTING. THE TWO POINT METHOD MAY BE USED WITH 2/7/2024 ISSUE FOR PERMIT THE SITE ELECTRICAL GROUNDING AS THE SECOND TEST POINT. THE NEC MAXIMUM GROUND PATH RESISTANCE FOR CURRENT CARRYING APPLICATIONS IS 25 OHMS. HOWEVER, GROUND ROD TO EARTH RESISTANCE UP TO 100 OHMS SHALL BE ACCEPTABLE FOR STATIC ELECTRICITY PROTECTION OF THE FILL AND VAPOR RISERS. #4 STRANDED BARE COPPER GROUND #4 STRANDED BARE TO GROUND CLAMPS GROUNDING OHMS NOTE: COPPER GROUND ON FILL RISERS TEST GROUNDING IMPEDANCE AT THE FILL RISERS. GROUNDING IMPEDANCE SHALL BE #4 STRANDED BARE (::D TO OTHER TANKS BELOW 25 OHMS PER CURRENT CEC CODE. IF IMPEDANCE IS OVER 25 OHMS, PLACE COPPER GROUND 3/4" GROUNDING ANOTHER GROUND ROD A MINIMUM 10 FEET AWAY FROM THE FIRST GROUND ROD TO GROUND ROD CLAMP W/TAP AND TIE THE RODS TOGETHER WITH SAME WIRE SIZE AND CONNECTIONS. MAKE SURE SCREW(TYP.) GROUND ROD IS INSTALLED INTO NATIVE SOIL. SEAL _ 8 3/4"0 x 12" LONG (D SOLID BRONZE ROD "T" CADWELD#4 4 (TYP.) STRANDED BARE COPPER WIRE CONNECTION TEST LEAD CONNECTED TO GROUND ROD (TYP.) (NOT LUG OR WIRING) 12" H-20 RATED 10 OHMS MAX ACCESS COVER #4 STRANDED BARE 2 #4 STRANDED BARE COPPER COPPER GROUND CONFIDENTIALITY STATEMENT: GROUND TO 3/4" 0 SOLID ROD 5 3/4" FRP BONDED #4 STRANDED WIRE TO #4 STRANDED BARE TO OTHER TANKS THE RECIPIENT OF THESE MATERIALS UNDERSTANDS THAT DOUBLE ENTRY BOOT 1/2"0 CADWELD GROUND COPYRIGHT IN THE MATERIALS IS OWNED BY BP,AND ALSO,THAT THE ATERIALS CONTAIN PRIVILEGED AND CONFIDENTIAL BUSINESS CADWELD "L" CONNECTION "BRAVO" MODEL NO. ROD CONNECTION COPPER GROUND MMATION OF Bp ACCORDINGLY,THE RECIPIENT AGREES TO INFOR TAIN THESE MATERIALS IN STRICT CONFIDENCE AND AGREES NO (TYP.) EXTERNAL -INTERNAL TO GROUND ROD RE F-07-GR TO DISCLOSE THESE MATERIALS TO ANY OTHER PARTY AND FURTHER AGREES NOT TO MAKE COPIES OF THE MATERIALS.THE SUMP WALL SUMP WALL RECIPIENT AGREES TO USE THE MATERIALS ONLY FOR THE LIMITED RECIPIENT AGREES TO RETURN ALL MATERIALS TO BP EITHER UPON -------------------------------------------------------------------------------------------------------------- COMPLETION OF THE INTENDED PURPOSE OR UPON THE REQUEST OF BP,WHICHEVER COMES FIRST. STATIC GROUNDING PLAN VIEW AND BONDING 0 �7 PIPE AND TANK DESIGN DISCLAIMER: BP DOES NOT AND CANNOT WARRANT THAT THE PLANS FOR PET OLEUM STORAGE AND DISPENSING ARE COMPLIANT WITH ALL A SCALE: 1" V-10" LEGAL REQUIREMENTS THAT EXIST OR AS THEY MAY BE APPLIED IN "T" CADWELD#4 THE FUTURE.NOR DOES BP WARRANT THAT A FUELING STORAGE Fl I I _1 AND D LIVERY SYSTEM CONSTRUCTED IN CONFORMITY WITH THES PLANS WI L BE FREE OF ALL LEAKS.YOU ARE ACCORDINGLY STRANDED BARE STRONGLY ENCOURAGED TO CONSULT WITH A FUELING STATION ENGINEER OF YOUR CHOOSING TO INDEPENDENTLY EVALUATE 1/2" 0 X 10' LONG AV- COPPER WIRE WHETHER THESE PLANS ARE TRULY SUFFICIENT FOR CONSTRUCTING THE STORAGE AND DELIVERY SYSTEM AT YOUR COPPER CLAD STEEL GROUND ROD DETAIL CONNECTION STATION. 12" H-20 RATED ACCESS COVER GROUND ROD IN (TYP.) NATIVE 4"0 BRONZE PIPE DEVELOPMENT INFORMATION 6 CLAMPS (TYP.) UNDERGROUNDSTORAGE CADWELD#4 WIRE CABLE TO GROUND ROD OR GROUND ROD CLAMP TANKSTANDARDS, 1/2" 0 X 10' LONG COPPER CLAD ELEMENT TP01 V-15.0 2023 SERIES CE) STEEL GROUND ROD IN NATIVE 4" FILL AND STAGE TERMINAL CONNECTION SOIL I RETURN PIPES 4 STRANDED BARE 5 #4 �TRANDED BARE 2 OPPER GROUND TO 3/4" 0 (TYP.) COPPER GROUND SOLID ROD CADWELD "L" 2 #4 AWG STRANDED FILL SIDE CONTAINMENT WIRE CONNECTION SITE ADDRESS, (TYP.) BARE COPPER GROUND CONTAINMENT SUMP (TYP.) ANCHORING PLATE WIRE (LFANK BOX (TYP.) (�ANK 4"0 COPPER GROUND L_2 A 4607 S. AIRPORT WAY 4 CLAMPS. "BURNDY No. 6 + 3/4"0 x 12" LONG BRONZE STOCKTON, CA 95206 GROUND ROD DETAIL (TYP.) FINISHED GAR224C" ROD (TYP.) SURFACE (TYP ) 0.-0� 'C�-0 RISER (TYP.) NOTE: DESIGNED BY: ALLIANCE Z&DM: FOR PENETRATIONS OF THE SUMP WALLS, SOLID AAK BRONZE STUD BOLTS ARE TO BE USED AND THE CHECKED BY: BP REPM x INTERIOR SUMP GROUND WIRES ARE TO BE 0 DRAWN BY: ALLIANCE PM 6 CONNECTED VIA TERMINAL CONNECTORS TO THE TAF CD (TYP.) ---------- BOLTS. BOLTS TO BE SEALED BOTH INSIDE AND OUT VERSION 1/2" 0 X 10' LONG COPPER CLAD 8 GROUND CLAMP AT FILL SUMP WITH GLASS MATT& RESIN. CA-4795 STEEL GROUND ROD IN NATIVE (TYP.) SOIL DRAWING TITLE @ UST GROUNDING U B L E COIL STATIC GROUND WIRE CABLE UP Y- WALL TANKS EXTREME CAUTION MUST BE OBSERVED WHILE USING ANY NON-INTRINSICALLY SAFE DETAILS DEVICE IN CLASSIFIED AREAS. SUMP MUST BE TESTED FOR VOLATILE VAPORS PRIOR T &SECURE TO SIDE OF GALVANIZED PEAGRAVEL TO USE. ELECTRICAL CONNECT MUST BE MADE WITH JUMPER WIRE SO FINAL STEEL RISER BACKFILL CONNECTION IS AWAY FROM CLASSIFIED AREAS. SHEET NO: NOTE: ------------.... ............... ALL EXTERIOR WIRE PENETRATIONS STATIC GROUNDING ARE REQUIRED TO BE CAD WELDED TO EARTH ELEVATION AND BONDING- I I " i� SCALE: 1" = V-10" (GROUND ROD INSTALLED IN SOIL NOT PEAGRAVEL BACKFILL) Dc SCALE: NONE TYPICAL FILL SUMP