INSTALL_2024 - Laserfiche WebLink

Home Browse Search

Initial Setup Of The Console Using Workflow Wizard Setup>Pumps and Lines>PLLD This screen lets you setup parameters for individual lines when the leak monitoring mode for the line selected line is set PLLD. Also, if Leak Monitoring is not enabled (in "Setup>Pumps and Lines>Line") for at least one line, then none of the PLLD screens can be edited. The maximum number of lines that can be configured for Leak Detection is equal to the max- imum number of STPs as determined by your console. However, only those lines for which Leak Monitoring is set to PLLD (in "Setup>Pumps and Lines>Line") are shown. Automatic dialing or sending of PLLD alarms is setup in Automatic Events setup (Setup> Automatic Events). 40 071310 015 Il'aa F+,etyp Wmpr jinp 4ln" PLLD — PjFriPt W1 !an Canflgurdp Enaht1d #. D154Wrd 40 anirolleng Pump H8t .4e1ii[OE +rftkkr 3 PlptType EndrailexPPiSG3llSa3 - Nf+ 14 in tl lamiler Length tt[I �aN'1 2_9 in alamglpr Linsth # i loll■ Th.pflnal Cpollilent 8.p0O71�Q Select a line from the icon list on the bottom of the screen to configure. Configured Touch the radio button to enable or disable the PLLD feature for the selected line. NOTE: In setup wizard, you should enable settings as you go. Controlling Pump Touch to enter pump controlling this tank. Note: Pump must be programmed to use Pump Control (see "Setup >Pumps and Lines >PLLD" on page 48). Pipe Type Touch to enter the pipe type for this line. Refer to the 'Supported Pipe Types and Line Lengths' table in the Veeder—Root Electronic Line Leak Detectors Application Guide (P/N 577013-465). NOTE: The fields that display below are dependent on, and applicable to, the PipeType selected. For example, if you select 2/3 IN. FIBERGLASS, the applicable fields that display will allow you to enter lengths for the 2" diameter and the 3" diameter pipe. If you select "user defined" pipe type, fields for setting up the 1st and 2nd line diameters, line lengths, and bulk modulus will display. Line Length The length of the piping between the tank and the dispensers, including the length between the check valve and where it connects into the product line. Line lengths are whole numbers. Values are in foot or meter increments, depending on system units. Allowable selections: Refer to the 'Supported Pipe Types and Line Lengths' table in the Veeder—Root Electronic Line Leak Detectors Application Guide (P/N 577013-465). The default is 0 but leaving it at 0 after entering a line length will cause a Setup Data warn- ing. Line Diameter Allowable selections: 0 to 3.00 in (0 to 76.20mm) The default is 0 but leaving it at 0 after entering a line length will cause a Setup Data warn- ing. Setup>Pumps and Lines>PLLD 2nd Line Length Allowable selections: Refer to the 'Supported Pipe Types and Line Lengths' table in the Veeder—Root Electronic Line Leak Detectors Application Guide (P/N 577013-465). Default: 0 2nd Line Diameter Allowable selections: 0 to 3.00 in (0 to 76.20mm) The default is 0. 1st Une Bulk Modulus [ only ava'dable if the pipe type is user -defined] The line's resistance to uniform nampressian. Reler to the 'Supported pipe Types and LIm Lengths' We In the V9eder—RW FJ%Iroic One Lok D2f%Ws Apple-atlon Guide ON 57701"66). Allowable selections-.1000 to 200,000 psi (6892 to 1,378,359kPa). The default is 0 but leaving it at 0 after entering a line length will cause a Setup Data warning. 2nd Line Bulk Modulus Lonly available if the pipe type is user -defined] The line's resistance to uniform compression. Refer to the 'Supported Pipe Types and Line Lengths' table in the Veeder—Root Electronic Line Leak Detectors Application Guide (P/N 577013-465). Allowable selections:1000 to 200,000 psi (6892 to 1,378,359kPa) The default is 0. Thermal Coefficient If the controlling pump assigned to the line has a tank assignment, this field is set to the thermal coefficient from that tank (see "Setup >Tank>General") and the field is read-only. If there is no tank assignment, you can edit this field. If the tank assignment is removed, the system will use the default thermal coefficient 0.00070 U.S. Units (0.00126 Metric Units). Allowable selections: 0.0 to 0.0016 gal./gal./°F (0.0 to 0.00288 I it./I it./°C) Continued on next page 48